Adding Bluetooth module
- MikeB
- 9x Developer
- Posts: 17996
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Adding Bluetooth module
I'm going to guess that at some point the "connect" signal was pulled the wrong way at power up. Since this is the "Chip Erase" signal at power up, this would erase the firmware.
Check in device manager to see if the processor is appearing as a device (other than 2 drives) when you plug in the USB.
I suggest removing the connection for the "connect" signal, then go here: viewtopic.php?f=123&t=5581, and follow the instructions in "9XR Pro Using SAM-BA to restore bricked Tx 2014-02-12.pdf".
Mike.
Check in device manager to see if the processor is appearing as a device (other than 2 drives) when you plug in the USB.
I suggest removing the connection for the "connect" signal, then go here: viewtopic.php?f=123&t=5581, and follow the instructions in "9XR Pro Using SAM-BA to restore bricked Tx 2014-02-12.pdf".
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Adding Bluetooth module
Thanks Mike!
that worked.
I am sure that is what happened
I have one of the BT modules where the trace from the "unused" pin is not apparent. I didn't cut any traces.
I will bypass the pin and connect to the board directly, which I also did on the 9x, I wasn't sure if that had caused me a problem on 9xtreme i had other issues when getting that one to work and thought I would give the pin another go.
again thank you very much.
that worked.
I am sure that is what happened
I have one of the BT modules where the trace from the "unused" pin is not apparent. I didn't cut any traces.
I will bypass the pin and connect to the board directly, which I also did on the 9x, I wasn't sure if that had caused me a problem on 9xtreme i had other issues when getting that one to work and thought I would give the pin another go.
again thank you very much.
-
- Posts: 2
- Joined: Fri May 06, 2016 2:17 am
- Country: -
Re: Adding Bluetooth module
Hi Mike,
I did everything as per instructions including connect a wire from erase pin (lower left pin of the J9 socket on the mainboard) to pin 34 of the HC-05 module but still can't set the bt role as master/slave. The only peculiar thing with my HC-05 is that there is no continuity between the button pad (left or right of the pad) and the pin34. That is why I decided to connect the wire straight to the pin 34. The Bluetooth module is powered up and I can see the module from my PC.BT diagnostic is all 0000. I'm using 9XR Pro with ersky9x-pr219 (V.4689-Mike) firmware. Any idea? Thanks.
I did everything as per instructions including connect a wire from erase pin (lower left pin of the J9 socket on the mainboard) to pin 34 of the HC-05 module but still can't set the bt role as master/slave. The only peculiar thing with my HC-05 is that there is no continuity between the button pad (left or right of the pad) and the pin34. That is why I decided to connect the wire straight to the pin 34. The Bluetooth module is powered up and I can see the module from my PC.BT diagnostic is all 0000. I'm using 9XR Pro with ersky9x-pr219 (V.4689-Mike) firmware. Any idea? Thanks.
Re: Adding Bluetooth module
Please post good pictures of your connections. Also a picture from the BT menu..
Did you change the BT Baudrate to 115200 in Radio setup/General??
João
Did you change the BT Baudrate to 115200 in Radio setup/General??
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Adding Bluetooth module
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 2
- Joined: Fri May 06, 2016 2:17 am
- Country: -
Re: Adding Bluetooth module
Hi jhsa,
I didn't realized that when I closed the back cover one of the wire was disconnected, too short. I made a longer cable and now I can set the BT role (master or slave). Thanks for your help anyways.
I didn't realized that when I closed the back cover one of the wire was disconnected, too short. I made a longer cable and now I can set the BT role (master or slave). Thanks for your help anyways.
Re: Adding Bluetooth module
Wonderful, well done
It happens Have fun..!!!
João
It happens Have fun..!!!
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Adding Bluetooth module
I've been reading through this thread and have added a bluetooth module to my 9xr-pro. I was wondering if it was possible to configure the radio via eepskye and bluetooth rather than using a usb connection? Can it be done? If so how?
Thanks
Thanks
Re: Adding Bluetooth module
Nope..
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- WesleyDiniz
- Posts: 24
- Joined: Thu Feb 23, 2017 1:34 pm
- Country: Brazil
- Location: Minas Gerais
Re: Adding Bluetooth module
folks I'm going to buy
bluetooth , Which would be better HC-05 OR HC-06 ,VERSION From my radio R220 , Could someone tell me Grateful
bluetooth , Which would be better HC-05 OR HC-06 ,VERSION From my radio R220 , Could someone tell me Grateful
Re: Adding Bluetooth module
HC-05,as it can be configured by the radio as Master and as Slave..
The HC-06 comes configured from factory, normally as Slave..
João
The HC-06 comes configured from factory, normally as Slave..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- WesleyDiniz
- Posts: 24
- Joined: Thu Feb 23, 2017 1:34 pm
- Country: Brazil
- Location: Minas Gerais
Re: Adding Bluetooth module
ok , Between this 2 what has More resource
HC-05 Better huh
HC-05 Better huh
- MikeB
- 9x Developer
- Posts: 17996
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Adding Bluetooth module
Yes, the HC-05 gives you more options as it can be swapped between master and slave from the firmware.
The HC-06 is fixed at the factory to either master or slave very difficult to swap to the other mode.
Mike.
The HC-06 is fixed at the factory to either master or slave very difficult to swap to the other mode.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Adding Bluetooth module
This is probably a very dumb question but apart from using BT as a trainer port can the BT be used for anything else?
Sent from my Nexus 9 using Tapatalk
Sent from my Nexus 9 using Tapatalk
- MikeB
- 9x Developer
- Posts: 17996
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Adding Bluetooth module
You may send the raw telemetry data out over bluetooth to a device that can decode and display it.
There is also a mode where the display contents are sent to eepskye, so eepskye may display the screen image. I put this in mainly to enable the capture of displays por posting on forums or adding to manuals.
Mike.
There is also a mode where the display contents are sent to eepskye, so eepskye may display the screen image. I put this in mainly to enable the capture of displays por posting on forums or adding to manuals.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Adding Bluetooth module
And it is a great feature Mike. I already used it on some of my videos, thank you.
One thing that Bluetooth could be used for, could be the exchange of models, settings, and perhaps voice files between 2 radios and also between a radio and eepskye.
This could be very useful at the field. I, for example, don't take a computer with me to the field
And it would be another killer feature in ersky9x.
Thanks
João
Sent from my thor using Tapatalk
One thing that Bluetooth could be used for, could be the exchange of models, settings, and perhaps voice files between 2 radios and also between a radio and eepskye.
This could be very useful at the field. I, for example, don't take a computer with me to the field
And it would be another killer feature in ersky9x.
Thanks
João
Sent from my thor using Tapatalk
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Adding Bluetooth module
Is this option available in the er9x version for the er9xtreme? I would really like to get gps coordinates etc passed through the telemetry link so I can record missions through my phone app via bluetooth!
Re: Adding Bluetooth module
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 19
- Joined: Thu Mar 16, 2017 9:15 pm
- Country: -
Re: Adding Bluetooth module
Hello,
can anyone tell me the correct type of desired connector on 9XR PRO board? I tried everything but I cannot find the right one. Looks like JST-something, PH maybe ? I found one in local R/C models store but it looked different, now when I searching on the web it looks like jst-ph 2 mm..
TM
can anyone tell me the correct type of desired connector on 9XR PRO board? I tried everything but I cannot find the right one. Looks like JST-something, PH maybe ? I found one in local R/C models store but it looked different, now when I searching on the web it looks like jst-ph 2 mm..
TM
Re: Adding Bluetooth module
Hi, is the cc-41 bluetooth module connected the same way as the hc-05? Thx.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 17996
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Adding Bluetooth module
Basically yes. Do you have an official one (HM-10) or a clone? The clones use a different command set.
I don't, currently, recommend BT LE 4.0 as the throughput is limited.
Mike
I don't, currently, recommend BT LE 4.0 as the throughput is limited.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Adding Bluetooth module
Good question MikeB. Here is the link.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: Adding Bluetooth module
so, for now the hc-05 will be good enough.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 17996
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Adding Bluetooth module
That is a clone, indicated by the missing crystal/resonator.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Adding Bluetooth module
HAya!
Soo after reading all this...and i know its 2021... And HATS OFF to all you guys for making this hobby interesting!
Just a simple question... can i put bluetooth on the 9xR for trainie and i already put one in the 9xRPRO as a trainer? Will it work?
Thx...
Soo after reading all this...and i know its 2021... And HATS OFF to all you guys for making this hobby interesting!
Just a simple question... can i put bluetooth on the 9xR for trainie and i already put one in the 9xRPRO as a trainer? Will it work?
Thx...
Re: Adding Bluetooth module
On the older 9XR, as far as I know it will not work. The same for the 9x radio with stock board.
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Adding Bluetooth module
Thx jhsa for the quick response!
Drummi
Drummi
Re: Adding Bluetooth module
Hi all,
will this hc-05 BT module work well on 3.3v out of com3? Thx.
will this hc-05 BT module work well on 3.3v out of com3? Thx.
- Attachments
-
- IMG_20220131_143707__01.jpg
- (620.67 KiB) Not downloaded yet
Last edited by OctavioS on Mon Jan 31, 2022 4:13 pm, edited 1 time in total.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: Adding Bluetooth module
Hi there, i know im a bit late, but did that module worked well with 3.3 volts?idar66 wrote: ↑Sun Dec 20, 2015 11:06 am hi mike thanks for help heres a pic of my modual http://openrcforums.com/forum/download/ ... &mode=view
http://openrcforums.com/forum/download/ ... =11345&t=1
plz can you take a look and tell me what i have to do to get running, ie do i copy what is pics above ie cutting tracks etc as the only thing i can see ive done different is i have not cut tracks and i have not soldered erase to the little button i have just plugged erase into the pins, i did unsolder the pinss and turned around so modual arieal faced out as ive fitted inside on other side of battery just like in photo in this forum, im really wanting to get this working so id really appreciate your help, thanks idar
thx
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 17996
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Adding Bluetooth module
Yes. I've only ever used a 3.3V supply to a HC-05 or a HC-06.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!