Er9x test versions

Post by **MikeB** » Mon Nov 25, 2013 11:50 am

This is NOT intended as a thread for discussions, just as somewhere I can put test versions of er9x for people to try out.
The idea is I'll put a specific test version on here, with a reason why it is here. Later, when I have something else to test I'll remove that one and replace it with another.
This should stop lots of test versions all over the forum, and help avoid the forum taking up more space on the server than it needs to.

Mike.

NOTE:
er9x r821 released on 30-Nov 2016
erskyTx r222 released on 03-Mar-2020
08-Jan-2016, er9x r820 is now released, also eepe r419.

er9xProv822w.zip: 03-Jan-2021 11:31
Fix (possibly!) PC4(L-WR) not working as extra digital input; (1.07 MiB) Downloaded 91 times

er9x-128StackTez.zip: 21-Nov-2020 21:59
Special test version for '128 with stack trace included
Also disable TelemetreZ processing when multiprotocol selected; (94.12 KiB) Downloaded 69 times

er9x-128StackTrace.zip: 20-Nov-2020 23:52
Special test version for '128 with stack trace included; (94.11 KiB) Downloaded 42 times

er9xProv822v.zip: 08-Nov-2020 20:45
Move EEPROM update call to remove recursive calls and therefore reduce stack usage; (1.07 MiB) Downloaded 98 times

eepe.zip: 26-Oct-2020 14:36
Fix Cyclic in simulator; (1.38 MiB) Downloaded 201 times

er9x-128PBfix.zip: 22-Oct-2020 23:45
Possible fix for extra push buttons; (93.86 KiB) Downloaded 77 times

er9x-128noboot.zip: 08-Oct-2020 15:05
Special version for '128 without the bootloader; (93.08 KiB) Downloaded 78 times

er9x-frsky.zip: 08-Oct-2020 12:14
Fix unable to select Sticky safety switch on M64; (74 KiB) Downloaded 89 times

er9xProv822u.zip: 19-Aug-2020 22:34
Add option to send "invert" command to multi module.; (1.07 MiB) Downloaded 204 times

er9x-frsky-AFHdebug1.zip: 15-Aug-2020 17:52
2nd Special test version of AFHDS2A telemetry debug (M64); (73 KiB) Downloaded 91 times

er9x-frsky-AFHdebug.zip: 13-Aug-2020 22:27
Special test version of AFHDS2A telemetry debug (M64); (73.05 KiB) Downloaded 81 times

er9xProv822t.zip: 31-Jul-2020 12:48
Multiprotocol subprotocol names built in to '128 and '2561; (1.07 MiB) Downloaded 159 times

er9x-128Green.zip: 20-Jul-2020 17:44
Test Build for '128 with "Green" processor, uses software watchdog.; (92.12 KiB) Downloaded 104 times

er9x-128SwWdog.zip: 20-Jul-2020 15:21
Special test version for M128. Implement 300mS software watchdog.; (92.1 KiB) Downloaded 96 times

er9x-128WD2S.zip: 20-Jul-2020 11:26
Special test version for M128. Watchdog set to 2 seconds instead of 0.5 seconds.
Only use this for testing "Green" processor.; (92.16 KiB) Downloaded 96 times

er9xProv822s.zip: 17-Jul-2020 21:18
M64 versions allow names for flight modes; (997.76 KiB) Downloaded 126 times

er9xProv822r.zip: 01-Jul-2020 23:34
Add FrSky hub telemetry from multi when using MULTI_TELEMETRY; (995.63 KiB) Downloaded 143 times

er9xProv822q.zip: 29-May-2020 22:35
Include multi-protocol names for non-telemetry firmware.; (992.33 KiB) Downloaded 200 times

er9x-128p.zip: 27-May-2020 23:30
Fix bug in MULTI_TELEMETRY handling (DSM RxV); (91.14 KiB) Downloaded 191 times

er9xProv822o.zip: 26-May-2020 20:36
Add DSM telemetry support with MPM and MULTI_TELEMETRY.
Improve handling of protocol names from MPM.; (981.73 KiB) Downloaded 132 times

eepe.zip: 16-May-2020 23:21
Support customise splash on M64 64x32 resolution; (1.38 MiB) Downloaded 261 times

er9xProv822n.zip: 04-Mar-2020 22:22
Support MPM using "MULTI_TELEMETRY" and AFHDS2A telemetry. This needs the MPM to use "MULTI_TELEMETRY" rather than "MULTI_STATUS".
Multi protocol names obtained from module.
SBUS protocol has polarity setting; (980.52 KiB) Downloaded 380 times

eepe.zip: 06-Feb-2020 23:58
fix a bug in handling the Multi protocol settings when reading from the radio.; (1.38 MiB) Downloaded 345 times

er9xProv822m.zip: 30-July-2019 16:47
V1 with flash space reduction (604 bytes on M64).
Also includes support for converting AIL, RUD and GEA switches to 3-position (ELE already supported).
Also included is an updated eepe.exe, needed to configure the 3-pos switches on the M64.; (2.35 MiB) Downloaded 701 times

eepeV2.zip: 31-May-2019 00:49
eepeV2 fix several issues with switch names and switches in the simulator; (1.38 MiB) Downloaded 499 times

er9x-2561.zip: 17-Apr-2019 19:02
2561 has global Voice Alerts; (92.91 KiB) Downloaded 351 times

er9x-128-dbgmenu.zip: 16-Mar_2019 19:18
V1 for '128 has a DEBUG menu in statistics; (92.45 KiB) Downloaded 332 times

er9x-128flex.zip: 08-Mar_2019 15:22
Add R9M flex support (untested with module); (92.29 KiB) Downloaded 277 times

eepe_eepeV2.zip: 05-Mar_2019 19:19
eepe and eepeV2, add support for R9M module; (2.77 MiB) Downloaded 343 times

er9xProv822k.zip: 07-Nov-2018 13:39
Fix missing display of IDx switch.; (992.69 KiB) Downloaded 467 times

er9xProv822j.zip: 19-Sep-2018 17:47
128 and 2561, Fix R9M power options; (990.81 KiB) Downloaded 349 times

er9xProv822h.zip: 08-Sep-2018 16:49
Add Hitec multi protocol
For '128/'2561, add voice 74 and 74 for throttle and switch warning; (990.75 KiB) Downloaded 278 times

er9xProv822g.zip: 09-Aug-2018 11:37
Add R9M support
Add more Multi protocols; (990.71 KiB) Downloaded 424 times

er9xProv822f.zip: 11-Apr-2018 23:44
FIx bug in timer trigger switch setting when extra PB is used.
Includes eepe.exe with a similar fix.; (2.35 MiB) Downloaded 475 times

er9xProv822e-128-2561.zip: 13-Mar-2018 13:07
For '128 and '2561 add custom names for flight modes
Test version for '128 and '2561 processors
with ability to set Failsafe from the Tx
with both FrSky and Multi protocols; (274.84 KiB) Downloaded 398 times

er9xProv822d-128-2561.zip: 11-Mar-2018 21:51
Test version for '128 and '2561 processors
with ability to set Failsafe from the Tx
with both FrSky and Multi protocols
There just isn't any spare flash space in the
'64 processor to add failsafe to those versions
V1 and V2 with eepe/eepeV2 as needed; (3.21 MiB) Downloaded 311 times

er9x-2561K1.zip: 03-Nov-2017 15:11
Test version for kmargos (2561); (88.91 KiB) Downloaded 645 times

eepe.zip: 25-Jan-2017 23:21
2nd attempt to fix related switch defaults bug!; (1.37 MiB) Downloaded 1323 times

eepe.zip: 25-Jan-2017 18:30
Fix related switch defaults bug!; (1.37 MiB) Downloaded 483 times

eepe.zip: 24-Jan-2017
Fix switch defaults bug; (1.37 MiB) Downloaded 483 times

er9xProv822a.zip: 15-Jan-2017 23:08
More Multi text added; (977.29 KiB) Downloaded 830 times

er9x-128.zip: 10-Nov-2016 22:59
'128 only, add "HuBRAW" processing; (87.93 KiB) Downloaded 659 times

er9x-frsky-olrsFix.zip: 04-Nov-2016 12:22
Possible fix for telemetry problem when using Orange lrs; (73.36 KiB) Downloaded 489 times

er9xProv821g_multiDSM-2.zip: 20-Sep-2016 10:21
MULTI DSM update on 128/2561
Only use with an updated MULTI module on DSM; (973.33 KiB) Downloaded 618 times

eepe.zip: 04-Aug-2016 23:32
Fix baudrate on telemetry menu; (1.35 MiB) Downloaded 665 times

er9xProv821f.zip: 03-Aug-2016 23:33
Add latest (FQ777) MULTI options; (388.53 KiB) Downloaded 615 times

er9x-128-2561p816.zip: 12-July-2016 15:01
Add 16/8 channel option for PXX protocol; (172.21 KiB) Downloaded 462 times

eepe.zip: 25-May-2016 11:47
Add "disable pre-read" option in settings; (1.35 MiB) Downloaded 532 times

er9xProv821e.zip: 12-Apr-2016 14:27
Correct MULTI FrSky CH_16 and CH_8; (386.9 KiB) Downloaded 556 times

er9xProv821d.zip: 07-Apr-2016 11:12
Add MULTI SFHSS and FrSky CH_16 and CH_8; (386.89 KiB) Downloaded 396 times

er9x-128P3a.zip: 21-Mar-2016 18:36
2nd Attempt to fix P3 problem; (85.52 KiB) Downloaded 390 times

er9xProv821c.zip: 16-Mar-2016 17:04
Add another MULTI protocol; (386.89 KiB) Downloaded 414 times

er9x-2561-128.zip: 09-Feb-2016 16:39
Special versions with "Mavlink over FrSky" support. Needs specific Arduino translator.
Telemetry Menu bug fixed; (170.73 KiB) Downloaded 380 times

er9x-2561-128.zip: 09-Feb-2016 12:21
Special versions with "Mavlink over FrSky" support. Needs specific Arduino translator.; (170.73 KiB) Downloaded 346 times

er9xProv821b.zip: 26-Jan-2016 10:51
Further MULTI changes
Re-label Delay up and down
Add Q242 sub-protocol on MULTI; (383.13 KiB) Downloaded 398 times

er9xProv821a.zip: 22-Jan-2016 16:19
Further MULTI changes; (383.05 KiB) Downloaded 425 times

er9xProv821.zip: 11-Jan-2016 14:32
H8_3D MULTI supported; (382.71 KiB) Downloaded 428 times

amod_last.zip: 23-Jan-2015 18:50
Fix the formatting of the .eepm file so it reads properly in eepe.; (26.36 KiB) Downloaded 491 times

petaca · Post by **petaca** » Fri Apr 24, 2015 12:20 pm

Dear Mike

I have installed on my TX:

er9x-R811
Version: V1.532-Mike
date 03.21.2014
mod: FRSKY - 128

I use EEPE program (version prior to 411).

My question is:

You may not copy EEPE in some pc setup menus of my radio?

For example, after copying all my models on the pc, I find the saved copy menu scales .... (SC1, SC2 ..... etc)

It is possible that the version of the program used EEPE not have ability to copy these menus from the radio tx to my pc?

I have thought that copying models from the pc to the transmitter radio, to review the SC1, SC2 menus, surprise !! .... Missing data SC1, SC2 etc ....

You believe that you need to update EEPE to solve this problem?

thank you very much

gabriel

Post by **MikeB** » Fri Apr 24, 2015 1:17 pm

The latest eepe version is 412. You may downloadit from here: https://code.google.com/p/eepe/source/b ... nstall.zip.

The definitely works reading the Scalers from the radio, I just tested it.

Mike.

Daedalus66 · Post by **Daedalus66** » Fri Apr 24, 2015 2:10 pm

Just a reminder from Post #1:
"This is NOT intended as a thread for discussions, just as somewhere I can put test versions of er9x for people to try out."

QuarX · Post by **QuarX** » Sat May 09, 2015 11:29 pm

Dear Mike
Thank you very much for your great work!!, very appreciated here.
I have installed on my TX:

Version: V1.285-Mike
SVN: er9x-r818
date 04.27.2015
mod: FRSKY - 128

I have made the telemetry mod and it work well, but with this firmware version the THR and AIL switches are not working.
Any way to activate the switch mod in this version?
EDITED:
SORRY!! i can see now the option telemetry mod don in the "general configuration"
Works like a charm!
Thank you very much for this state of the art piece of software.
Best Regards
Jose A.

andrenoites · Post by **andrenoites** » Sun Jul 10, 2016 11:24 am

Hello Mike

I am testing you latest er9xProv821e firmware in my 9xr with a XJT module and it's working really good:

er9xProv821e.zip
12-Apr-2016 14:27
Correct MULTI FrSky CH_16 and CH_8
(386.9 KiB) Downloaded 111 times

The only thing I can't configure is the number of channels in the PXX D16 protocol, this is a really important feature because in a Taranis we can change from 16CH to 8CH and the frame size is reduced from 18ms to only 9ms.

In the disclaimer of your latest test version it shows "Correct MULTI FrSky CH_16 and CH_8"
Is this the same feature I am talking about? if not could it be possible to add this feature?

Thank you for your awesome work, I really enjoy flying with your firmware

zipray · Post by **zipray** » Sun Sep 04, 2016 12:16 pm

Hello Mike

Magic Mike, salute to you.
I have installed on my 9xr with a Multiprotocol-TX-Moduleand.it's working really good in Serial mode.

Version: V1.542-Mike
SVN: er9x-r820
date 04.27.2015
mod: FRSKY - NT

I want to know, can I use the futaba simulator interface to connect the bluetooth module receiving telemetry data using a mobile phone or computer?

Post by **MikeB** » Sun Sep 04, 2016 3:44 pm

As mentioned in the first post "This is NOT intended as a thread for discussions, just as somewhere I can put test versions of er9x for people to try out."
Please post your question in another thread that is more suitable.

Mike.

phil · Post by **phil** » Fri Dec 01, 2017 6:58 pm

Hello Mike, I got a small problem again. I bought the very cheap transmitter Turnigy 9x with AFHDS2A protokol. I can not bind with the er9x software, r820. the default binding PPM and the stored "multi" file with AFHDS2A does not get any binding. Is that a big problem or should I get a 4in1 module. would ersky9x run in this station? Sincerely, Siegi

Post by **MikeB** » Fri Dec 01, 2017 8:37 pm

Please try using PPM but change the POLARITY to NEG.

Mike.

phil · Post by **phil** » Sat Dec 02, 2017 4:52 am

Thanks Mike, I've already tried all possible settings. the receiver does not matter, the flashing of the lamp is always the same, no twitch. I'm not an individual case, in the review has written one that after the installation of er9x no binding was possible, only with a multi-module. thanks, and best regards, Siegi

Post by **MikeB** » Sat Dec 02, 2017 10:43 am

Please go over to this thread:
viewtopic.php?f=5&t=10578&p=133564#p132741
where this Tx is discussed.
It was reported there that all worked when using PMM with NEG polarity.

Mike.

phil · Post by **phil** » Sat Dec 02, 2017 1:20 pm

Hello Mike, thank you very much for the info. I have been able to bind only one receiver in the delivery condition. the second he accepted but without function. I then had to tie the first receiver again. Now with er9x-d I have been able to bind the original with many different binding methods. I was also able to tie the 2nd FS IA6B, but the servos did not work. I could not tie a 3-passenger TGY IA6. I suspect that the transmitter module AFHDS2A has a binding weakness. warm regards Siegi

phil · Post by **phil** » Sun Feb 04, 2018 5:09 pm

hello, in my Turnigy 9x I have installed er9x, version 820th now I would like to load the test version 820 and have problems. PC, Programmer is equally the driver. With the software load command, the eepe program starts correctly and one thinks it is completely compromised. After a short while the eepe stops and the info follows: Loading not possible. I have a riddle, have tried many things like other drivers, other programmers, but the final loading was not possible. What I do not understand, I could load the standard software. Thank you

Daedalus66 · Post by **Daedalus66** » Sun Feb 04, 2018 8:33 pm

Phil
Mike has asked you repeatedly NOT to use this thread for discussion.

Sent from my iPhone using Tapatalk

Svarog · Post by **Svarog** » Mon Sep 24, 2018 9:07 pm

er9xProv822j.zip
19-Sep-2018 17:47
128 and 2561, Fix R9M power options
Installed the firmware and happy to fly with the R9M module. The switches are soldered to the standard contacts of the processor, whether some MOD is necessary for the operation of Frsky telemetry? (machine translation, sorry)))

Daedalus66 · Post by **Daedalus66** » Tue Sep 25, 2018 11:17 am

See previous post. Please don’t clutter this thread with discussion of other topics.

openrcforums

Er9x test versions

Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions

Re: Er9x test versions