FrSKY DHT module to 9Xtreme board connections
FrSKY DHT module to 9Xtreme board connections
I read on the forum that the black and white wires from the 9Xtreme board go to DHT module. Do the remaining Positive(+) and Negative (-)terminals on the DHT module get used, and if so where?
Much appreciated if someone could answer?
Much appreciated if someone could answer?
- KAL
- Posts: 552
- Joined: Thu Oct 10, 2013 4:36 pm
- Country: Germany
- Location: somewhere near Rothenburg ob der Tauber
Re: FrSKY DHT module to 9Xtreme board connections
Usually you connect the DHT via the red (+), black (-) and yellow (ppm) wires.
Then you only need TxD (black wire from 9XT) and RxD (white wire from 9XT) of the telemetry port.
5V and GND of the telemetry port have to be left alone.
Klaus
Then you only need TxD (black wire from 9XT) and RxD (white wire from 9XT) of the telemetry port.
5V and GND of the telemetry port have to be left alone.
Klaus
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
Re: FrSKY DHT module to 9Xtreme board connections
ersky9x, in protocol menu has internal and external module on/off. I assume that internal is for intance a dht module, and its possible to switch it on and off, so we can use an external one, right?
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 18000
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: FrSKY DHT module to 9Xtreme board connections
Yes, if either module is OFF, then power to that module is switched off.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: FrSKY DHT module to 9Xtreme board connections
Humm, let me see if I got it right.
If either module is off, obviously a dht will be off, right. If internal is on, then a dht will be on, right? What if both are on and I have an external module, will I be able to use 16 channels with a djt? Thx.
Enviado do meu Galaxy S6 edge através de Tapatalk.
If either module is off, obviously a dht will be off, right. If internal is on, then a dht will be on, right? What if both are on and I have an external module, will I be able to use 16 channels with a djt? Thx.
Enviado do meu Galaxy S6 edge através de Tapatalk.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: FrSKY DHT module to 9Xtreme board connections
Mike, then I have just also realized that it makes no sense the radio being powered from the trainer jack. You could use whatever pin you use for sensing it for something else
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FrSKY DHT module to 9Xtreme board connections
Both modules will be ON and you can send 8 channels to one and the other 8 to the other. You need 2 receivers of courseOctavioS wrote:Humm, let me see if I got it right.
If either module is off, obviously a dht will be off, right. If internal is on, then a dht will be on, right? What if both are on and I have an external module, will I be able to use 16 channels with a djt? Thx.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FrSKY DHT module to 9Xtreme board connections
That was what i thought.jhsa wrote:Both modules will be ON and you can send 8 channels to one and the other 8 to the other. You need 2 receivers of courseOctavioS wrote:Humm, let me see if I got it right.
If either module is off, obviously a dht will be off, right. If internal is on, then a dht will be on, right? What if both are on and I have an external module, will I be able to use 16 channels with a djt? Thx.
João
thx
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 18000
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: FrSKY DHT module to 9Xtreme board connections
1. The jack power doesn't use an extra pin to turn the power on or sense power is due to the jack being plugged in.jhsa wrote:Mike, then I have just also realized that it makes no sense the radio being powered from the trainer jack. You could use whatever pin you use for sensing it for something else
João
2. Sensing jack power causes the the trainer signal to be an output instead of an input.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: RE: Re: FrSKY DHT module to 9Xtreme board connections
I thought this was controlled by the software in the 9xtreme.MikeB wrote: 2. Sensing jack power causes the the trainer signal to be an output instead of an input.
Mike.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FrSKY DHT module to 9Xtreme board connections
Hi, if we fork the 9xtreme telemetry wire (tx/rx) to the dht and djt simultaneously, will the telemetry work?
Enviado do meu Galaxy S6 edge através de Tapatalk.
Enviado do meu Galaxy S6 edge através de Tapatalk.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: FrSKY DHT module to 9Xtreme board connections
Hmmm, good question.. it could, but ONLY if both modules are NEVER on at the same time.
Not sure if some kind of circuitry would be needed..
João
Not sure if some kind of circuitry would be needed..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FrSKY DHT module to 9Xtreme board connections
Ok. Then if I get the telemetry just from one module, will the telemetry info be accurate for the whole model?
Enviado do meu Galaxy S6 edge através de Tapatalk.
Enviado do meu Galaxy S6 edge através de Tapatalk.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: FrSKY DHT module to 9Xtreme board connections
If the receiver bound to that module is inside the model and connected to sensors, yes it will..
It will not tell you if the other receiver loses signal though. So it is very important that the telemetry receiver is the one with the main controls..
João
It will not tell you if the other receiver loses signal though. So it is very important that the telemetry receiver is the one with the main controls..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW