9xr pro total shot down
9xr pro total shot down
hi everybody! pls give me any idea on how to restore my 9xr pro function? after pressing the button near the usb port while powering up( following the instruction of "SAMBA restoring a brick transmitter") the screen totally shot off the only remaining function is the light, i have downloaded the SAMBA 2.18 on my laptop but i don't know what next step should i made, any help will be greatly appreciated, thank you guys in advance,
- KAL
- Posts: 552
- Joined: Thu Oct 10, 2013 4:36 pm
- Country: Germany
- Location: somewhere near Rothenburg ob der Tauber
Re: 9xr pro total shot down
Hi,
I have no experience in doing this but I can point you to some info:
Go to this thread. At the end ot the first post you'll find a PDF which shows you how to restore the firmware.
And in this post you'll find a ZIP with all files you will need.
Klaus
I have no experience in doing this but I can point you to some info:
Go to this thread. At the end ot the first post you'll find a PDF which shows you how to restore the firmware.
And in this post you'll find a ZIP with all files you will need.
Klaus
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
- MikeB
- 9x Developer
- Posts: 18000
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9xr pro total shot down
The instructions in "9XR Pro Using SAM-BA to restore bricked Tx 2014-02-12.pdf" should get you working again. Make sure you run the option to set the NVM bit that enables "execute from flash". You would not be the first person to do everything else OK and then wonder why it still doesn't work!
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9xr pro total shot down
KAL wrote: ↑Sun Nov 18, 2018 4:23 pm Hi,
I have no experience in doing this but I can point you to some info:
Go to this thread. At the end ot the first post you'll find a PDF which shows you how to restore the firmware.
And in this post you'll find a ZIP with all files you will need.
Klaus
[thanks kal for your responce ill work on this and get back to you for the result]
Re: 9xr pro total shot down
MikeB wrote: ↑Sun Nov 18, 2018 11:18 pm The instructions in "9XR Pro Using SAM-BA to restore bricked Tx 2014-02-12.pdf" should get you working again. Make sure you run the option to set the NVM bit that enables "execute from flash". You would not be the first person to do everything else OK and then wonder why it still doesn't work!
Mike
[thanks mike]
Re: 9xr pro total shot down
hello mike, can i use the SAMBA v2.18?
- MikeB
- 9x Developer
- Posts: 18000
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9xr pro total shot down
I would think so, although I never tried SAMBA since v2.12.
For just flashing the firmware, you should be able to select a board type of at91sam3s8-ek, no need to change any of the SAMBA configuration files. Those changes are only needed to allow access to the EEPROM from SAMBA.
Mike
For just flashing the firmware, you should be able to select a board type of at91sam3s8-ek, no need to change any of the SAMBA configuration files. Those changes are only needed to allow access to the EEPROM from SAMBA.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9xr pro total shot down
thanks mike