New Frsky Hall Effect Gimbals
New Frsky Hall Effect Gimbals
Hi Guys
Can these gimbals be fitted to the T9X Extreme?
regards
Hans
Can these gimbals be fitted to the T9X Extreme?
regards
Hans
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: New Frsky Hall Effect Gimbals
Hi lancaster,
Can you link to where these New FrSky Hall Effect Gimbals are (can be found) ?
Bob B.
Can you link to where these New FrSky Hall Effect Gimbals are (can be found) ?
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
-
- Posts: 313
- Joined: Thu Dec 29, 2011 10:18 am
- Country: Australia
- Location: Cooloola Cove, Australia
Re: New Frsky Hall Effect Gimbals
Try here : /www.horusrc.com/en/new-frsky-m9-high-se ... -plus.html. I don't think they are available just yet.
Dave
Dave
Re: New Frsky Hall Effect Gimbals
Hi Bobbob195558 wrote:Hi lancaster,
Can you link to where these New FrSky Hall Effect Gimbals are (can be found) ?
Bob B.
The gimbals are also shown on the Banggood site
https://goo.gl/hCkeFg
Hans
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: New Frsky Hall Effect Gimbals
FRSKY HORUS X12S GIMBAL ($60.00): (https://www.horusrc.com/en/receivers-ac ... imbal.html).
Edit: Then these are not the ones you were referring too.
The link above was not working, I fixed the link, works now.
Bob B.
Edit: Then these are not the ones you were referring too.
The link above was not working, I fixed the link, works now.
Bob B.
Last edited by bob195558 on Thu Jan 19, 2017 3:07 pm, edited 2 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
-
- Posts: 313
- Joined: Thu Dec 29, 2011 10:18 am
- Country: Australia
- Location: Cooloola Cove, Australia
Re: New Frsky Hall Effect Gimbals
Hi Bob, your link does not work for me, but the link I posted and the link Lancaster posted are both for the same item.bob195558 wrote:FRSKY HORUS X12S GIMBAL ($60.00): (ttps://www.horusrc.com/en/frsky-horus-x12s-gimbal.html).
Edit: Then these are not the ones you were referring too.
Bob B.
Dave
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: New FrSky Hall Effect Gimbals (M9 Hall Effect Gimbals)
Thanks Dave, I fixed the link, it works now.
Edit: M9 Hall Effect Gimbal, see here for more info: (viewtopic.php?f=122&t=9683).
There is a Problem, with the voltage for the FlySky and Turnigy 9x Radios which use 5Vs with there Gimbals circuit.
Bob B.
Edit: M9 Hall Effect Gimbal, see here for more info: (viewtopic.php?f=122&t=9683).
There is a Problem, with the voltage for the FlySky and Turnigy 9x Radios which use 5Vs with there Gimbals circuit.
Bob B.
Last edited by bob195558 on Tue Jan 24, 2017 12:58 pm, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: New Frsky Hall Effect Gimbals
Seems like we'll have to add a stepdown, or maybe 9xtreme can provide 3.3V?
Re: New Frsky Hall Effect Gimbals
When you install the 9xtreme the gimbals connect to it anyway, so they will be supplied with 3.3V
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: New Frsky Hall Effect Gimbals
Awesome, thanks. I have nearly ordered a 3.3V Pololu in the meantime
Seems like M9 are than Aurora 9x, if I install the Aurora gimbals while M9 are in transit, I'll have issues installing them later?
Seems like M9 are than Aurora 9x, if I install the Aurora gimbals while M9 are in transit, I'll have issues installing them later?
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: New Frsky Hall Effect Gimbals
MikeB wrote:Note that the SKY board, AR9X board, 9Xtreme and 9XR-PRO are all 3.3V based and only supply 3.3V to the gimbal pots.
Mike.
M9 Hall Effect Gimbal, see here for more info: (http://openrcforums.com/forum/viewtopic ... 122&t=9683) and here: (http://openrcforums.com/forum/viewtopic.php?f=97&t=9609) and (http://openrcforums.com/forum/viewtopic.php?f=95&t=9977).MikeB wrote:You are not down to 6.6 bits more like 9.3 bits.bob195558 wrote:10 bits down to 6.6 bits, would this, in actually = 6 bits only or can it use the .6 bits ?
We use some over sampling with averaging to turn the 10 bits into 11 bits already.
I just tried moving a stick on a Taranis (12 bits analog), and I'm struggling to get the output to change by less than 0.3%.
I wouldn't be surprised to find a resolution of 680 steps on a stick is actually OK.
When I put a 'scope on the PPM output of my Hitec Eclipse 7, I found the pulse width changed in steps of 2.5uS. Since full movement of the stick in one direction only changed the pulse width by 400uS, this was only 320 steps across the full range of stick movement.
Mike.
Last edited by bob195558 on Fri Mar 03, 2017 2:30 am, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
-
- Posts: 241
- Joined: Tue Jan 15, 2013 9:41 pm
- Country: -
Re: New Frsky Hall Effect Gimbals
Does anybody know if the X12 gimbal frames will fit in Taranis? I'm glad the M9 gimbals will work in both my Taranis and 9X (with Sky board) but the X12 gimbals seem a bit better made with all metal frames.
Re: New Frsky Hall Effect Gimbals
They don't.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: New Frsky Hall Effect Gimbals
Here are two reviews of the new M9 Hall Sensor Gimbals by BMSWEB: FrSky Taranis M9 Hall Sensor Gimbals | Flight Test
(https://www.youtube.com/watch?v=NvawANhxUos).
And the second one: FrSky Taranis M9 Hall Sensor Gimbals | Stick Height Adjustment
(https://www.youtube.com/watch?v=CWeP4vABSRE).
Bob B.
(https://www.youtube.com/watch?v=NvawANhxUos).
And the second one: FrSky Taranis M9 Hall Sensor Gimbals | Stick Height Adjustment
(https://www.youtube.com/watch?v=CWeP4vABSRE).
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
-
- Posts: 241
- Joined: Tue Jan 15, 2013 9:41 pm
- Country: -
Re: New Frsky Hall Effect Gimbals
Does anybody know the thread on these sticks? Is it M3?
Edit: The second review says they are 3mm.
Edit: The second review says they are 3mm.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: New Frsky Hall Effect Gimbals
Will this be a problem with the SKY board, AR9X board, 9Xtreme, 9XR-PRO using the FlySky and Turnigy 9x radio cases ?
More M9 Hall effect gimbals info here: (viewtopic.php?f=122&t=9683#p123428).
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).