One of these moments where I doubt myself. I could swear that the FLVSS showed individual cell voltages in the telemetry screen when I tested one of the nightly builds. That doesn't seem to be the case anymore with the release build. All I'm seeing is combined cell voltage. Am I imaging things?
OpenTX 2.1 release on Taranis
FrSky X8R
FrSky FLVSS
Generic 3-cell LiPo
Thanks in advance for any pointers.
EDIT: Remembered how I did it. See my answer below.
OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
-
- Posts: 23
- Joined: Wed May 13, 2015 12:57 am
- Country: United Kingdom
OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
Last edited by quadfather on Fri Jul 24, 2015 6:58 pm, edited 1 time in total.
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages?
I saw that it was disappear as well.
I found that I can define it myself, additional 6 lines (one for each cell, 6 in my case) in the telemetry lines, and then place them into a telemetry screen.
Anyone have a different way?
I found that I can define it myself, additional 6 lines (one for each cell, 6 in my case) in the telemetry lines, and then place them into a telemetry screen.
Anyone have a different way?
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages?
No that's the way. It typically isn't of much use to see all cells when you can show both lowest and delta.
Envoyé de mon SM-G920F en utilisant Tapatalk
Envoyé de mon SM-G920F en utilisant Tapatalk
-
- Posts: 23
- Joined: Wed May 13, 2015 12:57 am
- Country: United Kingdom
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages?
Ha! I remember now. Cell examples for FLVSS below.
Add a new sensor.
To display the lowest cell voltage set it up like this
Type: Calculated
Formula: Cell
Cell Sensor: Cels
Cell Index: Lowest
To display the voltage difference between the highest and lowest cells set it up like this
Type: Calculated
Formula: Cell
Cell Sensor: Cels
Cell Index: Delta
Cell Index is the key here. You can also show individual cell voltages. Simply add a sensor for each cell of your battery, configure as above and select the cell number in the Cell Index.
Hope it helps.
Add a new sensor.
To display the lowest cell voltage set it up like this
Type: Calculated
Formula: Cell
Cell Sensor: Cels
Cell Index: Lowest
To display the voltage difference between the highest and lowest cells set it up like this
Type: Calculated
Formula: Cell
Cell Sensor: Cels
Cell Index: Delta
Cell Index is the key here. You can also show individual cell voltages. Simply add a sensor for each cell of your battery, configure as above and select the cell number in the Cell Index.
Hope it helps.
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
Cool, i did not know before what the "delta" do...
Very nice
-- עופר --
Very nice
-- עופר --
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
The lowest cell is indicated correctly on the telemetry screen, BUT the voice announced value is not accurate??
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
You didn't update your voice pack.
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
I belive I have latest voice pack installed and I face the same problem.
Which voice pack do you use?
Which voice pack do you use?
-
- Posts: 1
- Joined: Thu May 05, 2016 12:10 am
- Country: -
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
How you make the radio say's
lower battry cel?
tks
lower battry cel?
tks
Re: OpenTX 2.1 & FrSky FLVSS Individual Cell Voltages
If your custom sensor is called "lowc" I suppose you just have to add a special function like "play value" "lowc" ? I play the value of lipo consumption from VFAS this way, so it should also work for FLVSS.