Page 6 of 10
Re: Adding Bluetooth module
Posted: Tue Jan 05, 2016 7:43 pm
by Dbswans
Sigh.... Frsky dashboard not available iOS [emoji37]
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Tue Jan 05, 2016 9:21 pm
by Dbswans
Does this look right ?
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Tue Jan 05, 2016 10:59 pm
by MikeB
Yes, the 4F4B is "OK", received from the HC-06. THis is exactly what I have on a 9XR-PRO with a HC-06 in it.
Mike.
Re: Adding Bluetooth module
Posted: Wed Jan 06, 2016 12:24 pm
by Dbswans
Great ty
Sent from my iPhone using Tapatalk
Adding Bluetooth module
Posted: Fri Jan 08, 2016 9:12 pm
by Dbswans
Alright all time for some more brain picking .... Telemetry sensors is their a set / good/ bad ? I will be getting this RX also running CC3D on quadcopter would like voltage/speed/temp etc any recommendations? Also would I need this hub?
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Fri Jan 08, 2016 9:52 pm
by bob195558
Hi Dbswans,
Your may want to get the: FrSky D8R-XP- 8/8 Channel Receiver With CPPM over the: FrSky D8R-II Plus - 8 Channel Receiver.
Yes for the Hub also.
Sensors I would suggest: FrSky High Precision Vario (FVAS-02H) or the FrSky Normal Precision Vario (FVAS-02N), FrSky Temperature Sensor (TEMS-01) and if you can find the FrSky FLVS Lipo Voltage Sensor with or without LCD screen (I think they stopped making them though).
Not sure about speed sensor for D-series sensors.
Bob B.
Re: Adding Bluetooth module
Posted: Sat Jan 09, 2016 12:12 am
by Dbswans
Great thank you I was looking in to both those RX not real sure I understand the difference "CPPM" allows to run a second RX? For another 8 channels [emoji15]? Lol
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sat Jan 09, 2016 12:18 am
by Dbswans
Sorry I'm still learning
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sat Jan 09, 2016 12:42 am
by bob195558
With the D-series receivers you have to have a transmitter with each receiver.
The CPPM with the right hardware one connection can do 8 channels.
FrSky D8R-XP 8 Channel Receiver w/ RSSI output (for OSD) and CPPM. (CPPM carries all 8 channels on a single connection.)
See: (
https://alofthobbies.com/radio-gear/frs ... ivers.html) and (
http://frsky-rc.com/) and (
http://frsky-rc.com/product/pro.php?pro_id=21).
Using the X-series receivers you can use two receivers with each XJT module transmitter.
Bob B.
Re: Adding Bluetooth module
Posted: Sat Jan 09, 2016 4:49 pm
by Dbswans
Excellent thank you very much
Sent from my iPhone using Tapatalk
Adding Bluetooth module
Posted: Sun Jan 31, 2016 10:39 pm
by Dbswans
Ok guys got my HC-05 the other day preparing to instal it now to clarify to use this on I need to run wire from button (en) pin to pin 34 on board ? I also removed the button
Is the purpose of the wire to act as if the button is depressed constant ? If so could I just connect the two pads under the button ?
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 10:53 pm
by jhsa
There seem to be some different versions of the module.. we need to know which one you have.But please see this post.
viewtopic.php?f=122&t=5641&start=90#p107863
Try to measure as it show in the picture..
João
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:01 pm
by Dbswans
It appears I have the same one in that pic
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:01 pm
by Dbswans
Only I removed the push button
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:05 pm
by Dbswans
I would also like to remove the state/EN pins if they are not used ?
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:08 pm
by Dbswans
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:13 pm
by Dbswans
Have continuity from front tab of button to 34 pin
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:34 pm
by MikeB
Dbswans wrote:Is the purpose of the wire to act as if the button is depressed constant ? If so could I just connect the two pads under the button ?
No. When the signal is high, then the HC-05 is in "command mode" where the processor tells the HC-05 what to do. When the signal is low, then the HC-05 is in "communication mode", and the processor sends/receives data that is sent/received over the bluetooth connection.
You need this signal connected to the "erase" signal on the 9XR-PRO.
Mike.
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:36 pm
by jhsa
Dbswans wrote:Have continuity from front tab of button to 34 pin
Ok, then connect the ERASE pin (from radio) there..
João
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:41 pm
by Dbswans
Thank you for the explanation .... I'm just being ignorant lol what do I need to do to this chip to make sure that it's getting the signal ? I'm very sorry I keep reading threw this thread and seems a bit confusing as their are different boards
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:45 pm
by Dbswans
What pin is the erase pin ?
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:50 pm
by Dbswans
Sorry guys feeling like a fool atm
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:53 pm
by jhsa
Hmmm, what radio do you have?
João
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:54 pm
by Dbswans
9xr pro
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Sun Jan 31, 2016 11:55 pm
by Dbswans
Currently have 05 module installed
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Mon Feb 01, 2016 12:16 am
by Dbswans
Under the charge port ? [emoji15]
Sent from my iPhone using Tapatalk
Adding Bluetooth module
Posted: Mon Feb 01, 2016 12:30 am
by Dbswans
Bottom left pin erase pin ?
Re: Adding Bluetooth module
Posted: Mon Feb 01, 2016 12:57 am
by jhsa
Re: Adding Bluetooth module
Posted: Mon Feb 01, 2016 1:00 am
by Dbswans
This should be fine then right
sorry all and thanks for putting up with me lol
Sent from my iPhone using Tapatalk
Re: Adding Bluetooth module
Posted: Mon Feb 01, 2016 1:03 am
by jhsa
No problem.. I think you found it
João