9xr pro simulator
-
- Posts: 7
- Joined: Fri Jan 23, 2015 12:52 pm
- Country: -
9xr pro simulator
Hello!
Has anyone managed to set transmitter on simulator?
Realflight simulator does not recognize my transmitter.
I also have an older version of Turnigy 9x and there is no problem of setting after a few modifications with resistor......
Does anyone know the solution?
Best regards
Has anyone managed to set transmitter on simulator?
Realflight simulator does not recognize my transmitter.
I also have an older version of Turnigy 9x and there is no problem of setting after a few modifications with resistor......
Does anyone know the solution?
Best regards
Re: 9xr pro simulator
I have it configured in realflight rc7, and had no problem. In which port are you connecting?
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: 9xr pro simulator
In which port are you trying to connect? If its with the futaba port, you need to switch on the radio.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: 9xr pro simulator
With the JR/Spektrum port you don't turn on. Plugging in the cable turns on just the encoder.GajiraChongChong wrote:In which port are you trying to connect? If its with the futaba port, you need to switch on the radio.
Note that you should turn Trainer OFF in the Model Setup, General menu. Counter intuitive I know, but it refers to using the transmitter as Master, while for sim use it must be functioning as slave.. The trainer option is asking whether it wants to receive through the trainer port -- you want it to send.
I'm not sure whether RF requires a particular shift polarity in Protocol. Mine is set to POS and it works OK with Phoenix. The protocol should of course be PPM.
Hope this helps.
EDIT: Mike issued a new version of ersky9xr today. Now Trainer can be either ON or OFF and polarity should be NEG. This makes it consistent with ER9x.
-
- Posts: 7
- Joined: Fri Jan 23, 2015 12:52 pm
- Country: -
Re: 9xr pro simulator
Thanks, but i still got no signal from tx.
I still do not understand what to do.
I still do not understand what to do.
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
9xr pro simulator
The Pro works fine with a simulator. Please tell us what version of firmware, whether you are using the JR (audio jack) or Futaba trainer port and whether you have a module installed. I'll test it and provide instructions. Unlike the 9x with stock module, there is no need for a resistor solution..
Re: 9xr pro simulator
Are you inserting the trainer cable into the JR socket with the radio ON or OFF? Please plug the jack connector with the radio OFF.majstoralc wrote:Thanks, but i still got no signal from tx.
I still do not understand what to do.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 7
- Joined: Fri Jan 23, 2015 12:52 pm
- Country: -
Re: 9xr pro simulator
i use JR trainer port and this cable:
http://www.ebay.com/itm/USB-Flight-Simu ... 5af23ca764
Radio is off, when i plug trainer cable.
http://www.ebay.com/itm/USB-Flight-Simu ... 5af23ca764
Radio is off, when i plug trainer cable.
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: 9xr pro simulator
So you are using an old version of RF without the Controller or other official interface? But you said it worked OK with a 9x with resistor mod.
Please specify which version of the firmware you are using.
I can't, of course, duplicate your sim setup, so the best I can do is to tell you that the following settings on my 9XR Pro, running the latest test firmware, work fine with Phoenix, which should have the same input requirements as RF.
First thing to do is always to look at the graphic main screen to make sure the transmitter is doing something reasonable on at least the first four channels. Also, remove the module, just to keep things simple.
Nothing special needs to be done in the Radio Setup menus. Just make sure you have the right mode. And I believe RF uses AETR channel order. The Trainer menu doesn't matter, as it determines how the transmitter functions as Master, which for sim use the TX needs to serve as a Slave.
In the Model Setup menu, with your Phoenix model chosen, make sure the Protocol settings are:
Proto PPM 8CH 400 usec (it may work on the default 300 usec or 350, so you can try these if you have problems)
PPM FrLen 22.5msec (try 22 and 25 if it doesn't work or jitters)
PPM Drive OpenDrain (default)
1st Chan 1
Shift Sel NEG (try POS if sim doesn't react -- this is something that may vary with firmware version)
You might also try turning on TRAINER in Model Setup, General. It shouldn't make a difference as it's concerned with the Tx as Master, but I think it did in one version.
Good luck.
Please specify which version of the firmware you are using.
I can't, of course, duplicate your sim setup, so the best I can do is to tell you that the following settings on my 9XR Pro, running the latest test firmware, work fine with Phoenix, which should have the same input requirements as RF.
First thing to do is always to look at the graphic main screen to make sure the transmitter is doing something reasonable on at least the first four channels. Also, remove the module, just to keep things simple.
Nothing special needs to be done in the Radio Setup menus. Just make sure you have the right mode. And I believe RF uses AETR channel order. The Trainer menu doesn't matter, as it determines how the transmitter functions as Master, which for sim use the TX needs to serve as a Slave.
In the Model Setup menu, with your Phoenix model chosen, make sure the Protocol settings are:
Proto PPM 8CH 400 usec (it may work on the default 300 usec or 350, so you can try these if you have problems)
PPM FrLen 22.5msec (try 22 and 25 if it doesn't work or jitters)
PPM Drive OpenDrain (default)
1st Chan 1
Shift Sel NEG (try POS if sim doesn't react -- this is something that may vary with firmware version)
You might also try turning on TRAINER in Model Setup, General. It shouldn't make a difference as it's concerned with the Tx as Master, but I think it did in one version.
Good luck.
Re: 9xr pro simulator
I also see that that dongle is for the FMS Sim and for what i know it will not have the driver to use with another sim that not the specified one.majstoralc wrote:i use JR trainer port and this cable:
http://www.ebay.com/itm/USB-Flight-Simu ... 5af23ca764
Radio is off, when i plug trainer cable.
Correct me if im wrong.
This one below is allways a good option, since its all in one:
http://www.ebay.com/itm/All-In-One-RC-S ... 3a92065335
The one below if you prefer to use with the module and receiver in a wireless usage:
http://www.ebay.com/itm/F01842-12-in-1- ... 3ce1e03675
or if you like it buy the original one, since we should support software developers.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 18010
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9xr pro simulator
I'm just thinking about simulators. I used the FMS one some time ago, although when I replaced my main computer some years ago, I didn't bother to re-install it. However, when I did use it, I built a PIC based device to convert from PPM to serial so I could use my Tx to control it.
So, thinking about this, I could probably add a FMS serial output driver to ersky9x.
Anyone interested?
Mike.
So, thinking about this, I could probably add a FMS serial output driver to ersky9x.
Anyone interested?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9xr pro simulator
Why not making ersky9x behave as a joystick over USB/Bluetooth??
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 18010
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9xr pro simulator
Because I can add something to output serial quite quickly, which might go out over bluetooth which is serial anyway, while the USB joystick solution will take rather longer. Does FMS handle enough channels over a joystick input anyway?
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9xr pro simulator
But that will work only for FMS? Doesn't FMS work with a normal PPM to USB dongle?
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 18010
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9xr pro simulator
I have no idea! I've actually just installed it, fixed the missing .dll file to let it run on Windows 7, and dug out my PPM to serial (PIC based) adapter. Plugged this into my SKY board 9X and it all worked!
This definitely uses 19200 baud serial.
What, exactly, does a "normal PPM to USB dongle" actually do?
Mike.
This definitely uses 19200 baud serial.
What, exactly, does a "normal PPM to USB dongle" actually do?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- MikeB
- 9x Developer
- Posts: 18010
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9xr pro simulator
I said it wouldn't take long!
I just have a small initialisation problem to fix, but I have the FMS running directly from COM2 on my SKY board. This should therefore also work on the 'PRO.
Mike.
I just have a small initialisation problem to fix, but I have the FMS running directly from COM2 on my SKY board. This should therefore also work on the 'PRO.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9xr pro simulator
I assume that, if i choose the BT as trainer on, then master is enabled and off means as slave, right? I have HC-05.MikeB wrote:Because I can add something to output serial quite quickly, which might go out over bluetooth which is serial anyway, while the USB joystick solution will take rather longer. Does FMS handle enough channels over a joystick input anyway?
Mike.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: 9xr pro simulator
No, but that's an idea
At the moment as far as I know, it is only possible to receive trainer input over BT. Not send.. Unless Mike has some surprise for us, of course
João
At the moment as far as I know, it is only possible to receive trainer input over BT. Not send.. Unless Mike has some surprise for us, of course
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: 9xr pro simulator
Ok. What about BT as command mode, means that i can use this option to "issue" AT commands like for arduino?
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 18010
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9xr pro simulator
This is to put a HC-05 BT module into command mode where it accepts AT type commands. Combined with setting COM2 to "pass to BT" mode, it means I can type commands on a terminal and check exactly what the BT module does. This will then help me to code up the functions needed to get a HC-05 to pair with another BT module.
As with a lot of things, this needs me to find enough time to do it.
Mike.
As with a lot of things, this needs me to find enough time to do it.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9xr pro simulator
Ok, its just that i've seen that its possible to change from master to slave and vice versa, via AT command. I thought that that was already possible, but according to João BT usability its still very limited, so ill just wait your further development instead of venturing myself into "murky" areas. .
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: 9xr pro simulator
Hi to all,
today I received Phoenix RC V5 and I can´t get my Turnigy 9XR PRO (ersky9x-r202 V.3309) to communicate with the sim.
I´ve jacked the dongle in the JR socket, Phoenix recognizes my Tx (as the display lights up when inserting the cable), but it doesn´t get any signals while calibrating. No matter if module (Orange RX) is inserted or not.
I´ve setup a 4ch model in the tx - the display shows movement when I move the sticks - but the signals doesn´t arrive in Phoenix. I´ve set trainer to "on".
My signal setup is:
Proto PPM 8CH 300 usec
PPM FrLen 22.5msec
1st Chan 1
Shift Sel POS
I even tried another tx (Graupner MX-16) with which the sim works properly, so the dongle has to be ok. There must be sth. in my turnigy, which is set wrong, but even after 3h of trying, I can´t find where I am doing wrong.
Every hint or help is welcome!
Regards,
Robin
today I received Phoenix RC V5 and I can´t get my Turnigy 9XR PRO (ersky9x-r202 V.3309) to communicate with the sim.
I´ve jacked the dongle in the JR socket, Phoenix recognizes my Tx (as the display lights up when inserting the cable), but it doesn´t get any signals while calibrating. No matter if module (Orange RX) is inserted or not.
I´ve setup a 4ch model in the tx - the display shows movement when I move the sticks - but the signals doesn´t arrive in Phoenix. I´ve set trainer to "on".
My signal setup is:
Proto PPM 8CH 300 usec
PPM FrLen 22.5msec
1st Chan 1
Shift Sel POS
I even tried another tx (Graupner MX-16) with which the sim works properly, so the dongle has to be ok. There must be sth. in my turnigy, which is set wrong, but even after 3h of trying, I can´t find where I am doing wrong.
Every hint or help is welcome!
Regards,
Robin
- KAL
- Posts: 552
- Joined: Thu Oct 10, 2013 4:36 pm
- Country: Germany
- Location: somewhere near Rothenburg ob der Tauber
Re: 9xr pro simulator
Hi Robin,
welcome here.
I don't know much about the pro and sims but
please try to set trainer to off, 'cause the trainer TX receives signals from the student.
You want to send a signal so your TX must be set as student.
It's not clear from what you wrote so: Insert trainer cord while TX is switched off.
Protocol and frame length seem OK so try to play with Shift Sel.
Cheers
Klaus
welcome here.
I don't know much about the pro and sims but
please try to set trainer to off, 'cause the trainer TX receives signals from the student.
You want to send a signal so your TX must be set as student.
It's not clear from what you wrote so: Insert trainer cord while TX is switched off.
Protocol and frame length seem OK so try to play with Shift Sel.
Cheers
Klaus
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
Re: 9xr pro simulator
Hi Klaus,
thanks for your answer.
I´ve inserted the cable while the Tx was switched off (and I didn´t switch it on afterwards), but as the notice in the Sim disappeared, that no Tx is connected, I assumed that my Tx was recognized.
It just didn´t send signals to the Sim (or the Sim didn´t receive them), as any stick or switch movement wasn´t recognized while calibrating.
I´ve misunderstood the trainer option: I thought I am the one who is trained, so my Tx is allowed to send signals. I´ll change and try it later again with trainer off!
Regards
Robin
thanks for your answer.
I´ve inserted the cable while the Tx was switched off (and I didn´t switch it on afterwards), but as the notice in the Sim disappeared, that no Tx is connected, I assumed that my Tx was recognized.
It just didn´t send signals to the Sim (or the Sim didn´t receive them), as any stick or switch movement wasn´t recognized while calibrating.
I´ve misunderstood the trainer option: I thought I am the one who is trained, so my Tx is allowed to send signals. I´ll change and try it later again with trainer off!
Regards
Robin
Re: 9xr pro simulator
Try changing the shift from POS to NEG.
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: 9xr pro simulator
Agree. The symptoms are consistent with wrong shift. The transmitter is putting out a signal but it doesn't include pulses.
- KAL
- Posts: 552
- Joined: Thu Oct 10, 2013 4:36 pm
- Country: Germany
- Location: somewhere near Rothenburg ob der Tauber
Re: 9xr pro simulator
Received my PhoenixRC 5.0 yesterday.
After struggling with calibration of Phoenix I got all 8 channels working.
Proto PPM 8CH 300 usec
PPM FrLen 22.5msec
PPM Drive OpenDrain
1st Chan 1
Shift Sel POS (ersky9X-r214 / V.534 / 26.02.2015)
(connected via JR socket)
My problem was that I first didn't realize the way Phoenix distinguishes pots and switches.
Every channel that is centered while starting calibration is recognized as pot,
every channel that is at one of its extreme points is recognized as switch.
So if you want to use a 3-way-switch (e.g. for flaps) you have to leave it in mid position.
Otherwise it's recognized as 2-way-switch and at worst oszillates in mid position.
Edit: forgot to say that 3-way-switches have to be put to the end points while calibrating pots,
not while calibrating switches!
Klaus
After struggling with calibration of Phoenix I got all 8 channels working.
Proto PPM 8CH 300 usec
PPM FrLen 22.5msec
PPM Drive OpenDrain
1st Chan 1
Shift Sel POS (ersky9X-r214 / V.534 / 26.02.2015)
(connected via JR socket)
My problem was that I first didn't realize the way Phoenix distinguishes pots and switches.
Every channel that is centered while starting calibration is recognized as pot,
every channel that is at one of its extreme points is recognized as switch.
So if you want to use a 3-way-switch (e.g. for flaps) you have to leave it in mid position.
Otherwise it's recognized as 2-way-switch and at worst oszillates in mid position.
Edit: forgot to say that 3-way-switches have to be put to the end points while calibrating pots,
not while calibrating switches!
Klaus
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
9xr pro simulator
Thanks for the clarification. Just one addition for anyone trying it: if it doesn't work, try NEG shift. The polarity setting was changed in the latest version.
Re: 9xr pro simulator
OctavioS wrote:I also see that that dongle is for the FMS Sim and for what i know it will not have the driver to use with another sim that not the specified one.majstoralc wrote:i use JR trainer port and this cable:
http://www.ebay.com/itm/USB-Flight-Simu ... 5af23ca764
Radio is off, when i plug trainer cable.
Correct me if im wrong.
This one below is allways a good option, since its all in one:
http://www.ebay.com/itm/All-In-One-RC-S ... 3a92065335
The one below if you prefer to use with the module and receiver in a wireless usage:
http://www.ebay.com/itm/F01842-12-in-1- ... 3ce1e03675
or if you like it buy the original one, since we should support software developers.
I use this http://www.ebay.com/itm/All-In-One-RC-S ... 557991221?
It recognises fine in RF7 and PhoenixRC.
Futaba plug and radio On
Re: 9xr pro simulator
so I cant get my 9xr pro to connect with a 3.5 pack. Do I have to use the futaba cable port.
I am using SmartPropoPlus. It see's 8 channels but the channel levels do not change when I move the sticks.
I have adjusted the setting and stated above but it still does not work.
I am using SmartPropoPlus. It see's 8 channels but the channel levels do not change when I move the sticks.
I have adjusted the setting and stated above but it still does not work.