OpenTX - Nightly builds for pre-2.0 testing

[bertrand35]

Good question, I need tol readd the 'One' trigger. Please open an issue so that I don't forget it!

[ssatoru]

Thanks! I opened an issue.

Satoru

[Scott Page]

Question on 2.0 . How I can do the same as 'ONE' in Special Function to trigger once when model is loaded or radio is powered on? I have used it to initialize GVAR which was used as a counter.

Thanks.

Satoru

ON will accomplish the same thing.

[MicheleVilla]

Hi to all
OpenTx 2.0 last Night Build (16/05/14)
I have associate a 3-position switch to three phases of flight and I created three wav files Phase1-ON.wav, Phase2-ON.wav, Phase3-ON.wav.
Changing rapidly position the switch to the radio stores all the changes and plays messages as many times as they were on the move
Is possible to add a little delay and play only the last position?

[bertrand35]

Another enhancement issue is needed!

[MicheleVilla]

Open an Issue in Git?
Ok
thank You

[Scott Page]

No nightly build for 5/17?

[MicheleVilla]

Another question about variometer

setting
pitch at 0 700Hz
pitch at max 1700 hz
means that at 0 change sound run continuosly at 700 Hz
But at 0 change should not remain silent?

[mstrens]

Another question about variometer

setting
pitch at 0 700Hz
pitch at max 1700 hz
means that at 0 change sound run continuosly at 700 Hz
But at 0 change should not remain silent?

You can find more explanations about new vario sounds on this link
viewtopic.php?f=86&t=5081

You will see that per default there is no dead zone anymore (zone with no tone).
The 4 parameters in telemetry panel are used to define 3 ranges of VSpd, each having a different kind of tone. ge
If you want to mute the vario for some range of VSpd you must define customs switches based on VSpd.
This is more flexible (but a little more complex)

[pberki]

Hi,
Is there any key combination or any other way to lock the buttons so, they don't get pressed accidently while flying please ?
Thank you.
Peter

[MicheleVilla]

Ok thank you for information
I agree that it's a little more complicated(but more flexible)

I try to play with it

[janlebelg]

i have the sbus sensors it works fine but can not show -cell ans -cels on the screen it is always 0V
the power and +power is ok cell and cells are ok to wath dit i mis or is it a issuw an i report it on the nightly builds

i have the soft an bin of 16 05 2014
thanks

[bertrand35]

Cell- and Cells- always 0, are you sure? If yes, please open a new issue for that so I don't forget, I will have a look next week.

[MicheleVilla]

@Bertrand
About Issue 1111
Now is closed and I have send my last answer too late
This issue happens only whit converted memory from 215 to 216
With new model all is ok
Please may you check That?

EDIT:

Before LONG press <] must enable every switch you want to set
Now in this way all is Ok

[janlebelg]

Ok i make a new model

i made update every week
And today have also mixes and telemetry changes after it
Mixes that dont work and telemetry are replased by others

so i gona make a general test tomorow and poste the news

[janlebelg]

I updated today and all mixes or ok like before but there is non thelemetry on x6d an d4r taranis says no data

[davx]

Hi,

I just came back from my flight session with a Taranis and OpenTX for the first time, I must say I'm really impressed with this combo, thanks for the open source team !!

A little problem however, I was flying in crazy thermals and the flight chrono remained blocked on 1:16:40s. I know it's already a big value but my glider didn't want to land even after numerous loops and barrels

My firmware is the r2940 and I was wondering if you could extend the chronos duration somewhat in OpenTX 2 ?
Do I open an enhancement issue on github ?

Thanks again !

[Scott Page]

I updated today and all mixes or ok like before but there is non thelemetry on x6d an d4r taranis says no data

You updated from which build date to which build date?

[wilco1967]

I updated today and all mixes or ok like before but there is non thelemetry on x6d an d4r taranis says no data

You updated from which build date to which build date?

I noticed the same.

The nightly build from 18-may shows 'no-data' on telemetry pages, and all telemetry data remains 0. RC control works just fine, just no telemetry.
Went back to version from 16 may , which is OK.... (17 may does not seem to exist).

[dinamich]

Betrand did rework telemetry on 16.5 at 4pm so this changes are not in may-16 nightly, but are in may-18. This could be the cause.

[bertrand35]

It seems I broke something in my refactoring, I delete the build of may 18.

EDIT: No it's just stupid, the S.PORT is now enabled by a compile option and I forgot to include it in nightly builds. It should be ok tomorrow morning.

[dinamich]

Hi,

I just came back from my flight session with a Taranis and OpenTX for the first time, I must say I'm really impressed with this combo, thanks for the open source team !!

A little problem however, I was flying in crazy thermals and the flight chrono remained blocked on 1:16:40s. I know it's already a big value but my glider didn't want to land even after numerous loops and barrels

My firmware is the r2940 and I was wondering if you could extend the chronos duration somewhat in OpenTX 2 ?
Do I open an enhancement issue on github ?

Thanks again !

I will run a test for this. I have checked the code and timer is big enough uint16 which means 65535 seconds = more than 18 hours.

Are you sure you didn't cause a timer stop yourself?

[janlebelg]

hi putted the version of 15 05 in the taranis and went flying
everyting went "well" only i putted a new battery nannothech in my easy glider and when i was at 100m high
it went stead down to the eart an esplodes my glider 3 sensor an the x6d

It was the connector hxt 60 that was not soldert in factorry the scrinking held it togeter

so i am sorry but wil not be abel to test currend an votige for a will only have alti sensors left

I can confirm open TX dit not scratch my glider
regards

[jhsa]

Sorry to read this.. It's not nice.. Difficult to find this kind of problem.. Most of the times when you find it, it is to late..

João

[davx]

I will run a test for this. I have checked the code and timer is big enough uint16 which means 65535 seconds = more than 18 hours.

Are you sure you didn't cause a timer stop yourself?

I've read your answer and after some thoughts ( ), I had a doubt. It's a new setup and I'm also using my chrono switch to reset a counter, so to make the story short, I've just run a test and the chrono didn't stop at 1:17:40... It quietly continued to count

Thanks for taking the time

Tchao

[oiseau]

Hey guys, I upgraded to nightly and I'm enjoying the new changes

The only thing I've noticed is I can't get my custom sounds to show up in the Special Functions -> Play Track selection menu, only the default ones are there. I could get them in the old openTX, and I can still see them and play them in the file browser in the "long hold menu" screen.

Is this a known issue or some setting that I missed? Thanks!

Names too long? Now the maximum is 8 chars (compromise to allow 64 functions ...)

Yep, looks like that was it

Another question, what's the difference between Taranis and Taranis Plus targets? should I choose Taranis Plus if I have the upgrade parts?

Also, anything I need to know to get vibration working? I bought the addon from Aloft and installed it per instructions, and get nothing. May 5 and today's nightly versions tried.

edit never mind, had version A taranis but no way to tell without a scope... vibration motor sure is weak

[dinamich]

Another question, what's the difference between Taranis and Taranis Plus targets? should I choose Taranis Plus if I have the upgrade parts?

Taranis Plus has some changes in wiring, so stick with Taranis image, even with haptic upgrade.

[azure93]

Hello all !! I'm very thanks for all OpenTX members for this great job.

This is just one bug reporting for 2014.05.19 version.

Please refer SF11 & SF14 lines for all screens. It made in companion and running simulator & export to taranis.

As I assume, Inverted logic switch name are shifted in simulator & radio firmware.


PS ) Could somebody show lua function examples for model.getLogicalSwitch() & model.setCustomFunction() ?

I want make background music jukebox with lua script.

[Scott Page]

Hello all !! I'm very thanks for all OpenTX members for this great job.

This is just one bug reporting for 2014.05.19 version.

Please refer SF11 & SF14 lines for all screens. It made in companion and running simulator & export to taranis.

So simplify your report - in SF11 both the transmitter and simulator show !L7 but Companion shows !L6

In SF14 both the transmitter and simulator show !L12 but Companion shows !L11.

[rdeanchurch]

I believe this is reported and fixed in
https://github.com/opentx/opentx/issues ... ate=closed
!lxx shifted by one.