OpenFlightStab discussion

A gyro stabaliser to replace the orange stabilizer firmware.

Moderator: noobee

Post Reply
User avatar
ckleanth
Posts: 81
Joined: Sun Dec 23, 2012 11:19 pm
Country: United Kingdom
Contact:

OpenFlightStab discussion

Post by ckleanth »

Hi guys, currently the discussion is mainly at RCGroups

http://www.rcgroups.com/forums/showthread.php?t=1794672

cheers
If it has wings it will fly...

User avatar
Rob Thomson
Site Admin
Posts: 4543
Joined: Tue Dec 27, 2011 11:34 am
Country: United Kingdom
Location: Albury, Guildford
Contact:

Re: OpenFlightStab discussion

Post by Rob Thomson »

Yup. At some point the developer of the system was going to move all his stuff to here.

Not sure what his plans are these days :-)

Sent from my GT-I9300 using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
User avatar
ShowMaster
Posts: 4327
Joined: Thu Dec 29, 2011 3:44 am
Country: -
Location: Los Angeles, CA USA

Re: OpenFlightStab discussion

Post by ShowMaster »

I've been following his post. I have 2 of the HK stand alone orange stabilizers I bought when the model came out with the on off feature. I have no idea what the model or FW is. It's a second generation version.
I wasn't very happy trying it out on the bench because of serious servo noise. As soon as I connected the on/off control to my Frsky d6r the servos got really buzzy. I should try another model D receiver and maybe another system.

I found the topic on upgrading the FW to improve it and thought I'd try it on one unit. I've ordered a HK orange programmer that's still in shipping in Malaysia bound for the USA. Probably another week to wait.
Anyone trading this that's done the FW update please post your results. I'll do the same.
I understand this programmer will also work on the orange DSM tx module and receivers.
SM



Sent from my iPod touch using Tapatalk, small keys and a big finger.
dmyers7
Posts: 1
Joined: Sun Mar 30, 2014 9:12 pm
Country: -

Re: OpenFlightStab discussion

Post by dmyers7 »

This is a great update to the base firmware. It gives addition flight modes and the capability to adjust the gain on the fly or through mixing. I use these units on my crack laser and Pitts to help stabilize for gusts and wind; since these models are so lite. I mix my throttle position in to Ch6 to reduce gain at full throttle (prevent oscillation) and increase gain for slow and 3D flight. A must have firmware for these models :-) I'm using the ones with built in receivers and no case. These versions have a place you can solder a 6 pin header. This header becomes the programming port to red lash the firmware. Remember to use 3.3v and not 5v on the programming port or you will burn out the sensors on board (read the wiki). Have fun.


Sent from my iPad using Tapatalk
Using Tapatalk
User avatar
ShowMaster
Posts: 4327
Joined: Thu Dec 29, 2011 3:44 am
Country: -
Location: Los Angeles, CA USA

Re: OpenFlightStab discussion

Post by ShowMaster »

Good info, thanks. Now all I have to do is read up on the flash operation and give it a try. I have a HK orange programmer as well as USBasp and a FTDI. Not great at using them but I'm a fast learner with the how to info to read up on.



Sent from my iPod touch using Tapatalk, small keys and a big finger.

User avatar
Rob Thomson
Site Admin
Posts: 4543
Joined: Tue Dec 27, 2011 11:34 am
Country: United Kingdom
Location: Albury, Guildford
Contact:

Re: OpenFlightStab discussion

Post by Rob Thomson »

Watch out for the voltage.

I blew one up using a 5v programmer!

Sent from my GT-I9300 using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
User avatar
ShowMaster
Posts: 4327
Joined: Thu Dec 29, 2011 3:44 am
Country: -
Location: Los Angeles, CA USA

Re: OpenFlightStab discussion

Post by ShowMaster »

Rob Thomson wrote:Watch out for the voltage.

I blew one up using a 5v programmer!

Sent from my GT-I9300 using Tapatalk
Good to know. Thanks.


Sent from my iPod touch using Tapatalk, small keys and a big finger.
User avatar
ShowMaster
Posts: 4327
Joined: Thu Dec 29, 2011 3:44 am
Country: -
Location: Los Angeles, CA USA

Re: OpenFlightStab discussion

Post by ShowMaster »

Rob Thomson wrote:Watch out for the voltage.

I blew one up using a 5v programmer!

Sent from my GT-I9300 using Tapatalk
Good to know. Thanks.


Sent from my iPod touch using Tapatalk, small keys and a big finger.

Post Reply

Return to “OpenFlightStab”