DSM2 work
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
DSM2 work
Correct. While the logo is displaying... The routines have not yet loaded to initialise the module!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
DSM2 work
But then he's not correct.
Best to turn off the splash if you're going to bind... Otherwise yku have to hold the trainer switch until after the splash dissapears, and the bind light on the rx is solid.
---
I am here: http://maps.google.com/maps?ll=44.003067,-79.457256
Best to turn off the splash if you're going to bind... Otherwise yku have to hold the trainer switch until after the splash dissapears, and the bind light on the rx is solid.
---
I am here: http://maps.google.com/maps?ll=44.003067,-79.457256
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
DSM2 work
How is he not correct?
Hold for 1-2 seconds after the logo.. Then release.
Although... I do agree. I usually turn off my logo as easier to get it right!
Sent from my iPhone using Tapatalk
Hold for 1-2 seconds after the logo.. Then release.
Although... I do agree. I usually turn off my logo as easier to get it right!
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
He said let go right after the splash screen.
Didn't say anything about holding it after...
Didn't say anything about holding it after...
Last edited by cre8tiveleo on Sat Feb 04, 2012 9:35 pm, edited 1 time in total.
Re: DSM2 work
ok it binds now but no throttle. Do I need to change order from reta to something else. I am trying to flt a blade quad Qsm
Earl
Earl
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
DSM2 work
You want TAER. For the spektrum systems.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
You have to assign a function to each channel, right now you have a blank slate.
You could start with a basic 4ch template and build from that. (select a model - long right press, then select the model setup menu > right , keep goign right until you get to the templates, if you don't have templates, then .. oopise. in teh templates is a 4ch basc setup, try that)
And make sure you have TAER for spektrum, and I bet Rob just beat me to the post again...
You could start with a basic 4ch template and build from that. (select a model - long right press, then select the model setup menu > right , keep goign right until you get to the templates, if you don't have templates, then .. oopise. in teh templates is a 4ch basc setup, try that)
And make sure you have TAER for spektrum, and I bet Rob just beat me to the post again...
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
yup... and Manchester United sucks!
Just kidding.
Just kidding.
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
DSM2 work
Lol. I don't follow the footie
We need to get 'real lives'. Hanging out on forums is rather sad!
Sent from my iPhone using Tapatalk
We need to get 'real lives'. Hanging out on forums is rather sad!
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: DSM2 work
FANTISTAC !!! it works...Thanks
Earl with Blade quad
Earl with Blade quad
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
Yeah, but hanging out on openrcforums.com is a blast , helping people and confusing them while entertaining them is great... and I'm at work... bored, and miffed at the dx4e issue I have now... maybe it does do dsmx, but I can't get it to chirp into it's mode. it goes to france mode, regular mode and dsm2 mode.. but when I try dsmx.. nada... maybe it's just me... *shrugs*
European footbal is awesome, I follow it a bit.
European footbal is awesome, I follow it a bit.
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
Glad it worked out for you!
-
- Posts: 236
- Joined: Tue Dec 27, 2011 11:19 pm
- Country: -
- Location: Don Mills, Ontario
Re: DSM2 work
There is no chirp in DSMX mode.
Easy way to confirm that it is working:
Bind a DSM2 only receiver.
Switch to DSMX mode (same model memory).
Bind to a DSMX capable receiver
If DSMX mode worked then the first receiver will no longer connect.
Now bind the DSM2 receiver and the DSMx one will stop working.
You can also tell by how the receiver behaves if you cycle its power with the transmitter still on. In DSM2 mode the LED will flash to indicate that it thinks it has had a brownout.
Brownout detection is part of the quick reconnect function. If it finds the transmitter on the same pair of frequencies as it was previously then it assumes that a brown out has occurred.
DSMX mode does not support this simple brownout detection because the frequencies are always changing, so no flashing LED.
One limitation of using the DSMX mode - if you mix and match DSM2 and DSMX in your models you will have to rebind whenever you switch between them.
The module stays in whatever mode it was last bound, even if you switch model memories and/or the mode setting. The module stores the mode based on the last successful bind.
Pat MacKenzie
Easy way to confirm that it is working:
Bind a DSM2 only receiver.
Switch to DSMX mode (same model memory).
Bind to a DSMX capable receiver
If DSMX mode worked then the first receiver will no longer connect.
Now bind the DSM2 receiver and the DSMx one will stop working.
You can also tell by how the receiver behaves if you cycle its power with the transmitter still on. In DSM2 mode the LED will flash to indicate that it thinks it has had a brownout.
Brownout detection is part of the quick reconnect function. If it finds the transmitter on the same pair of frequencies as it was previously then it assumes that a brown out has occurred.
DSMX mode does not support this simple brownout detection because the frequencies are always changing, so no flashing LED.
One limitation of using the DSMX mode - if you mix and match DSM2 and DSMX in your models you will have to rebind whenever you switch between them.
The module stays in whatever mode it was last bound, even if you switch model memories and/or the mode setting. The module stores the mode based on the last successful bind.
Pat MacKenzie
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
DSM2 work
Good to know.
Thanks, you saved a life today.
Doesn't help when the manual states when goin into dsmx mode it should chirp.
Thanks, you saved a life today.
Doesn't help when the manual states when goin into dsmx mode it should chirp.
Re: DSM2 work
Well things are working ALMOST...left and right on the quad are reversed. I have tried INV on ALE and ELV and it seems to have no effect. I haven't tried the rudder control yet. It should be the YAW. But overall, flying my mini quad with the er9x is GREAT. I bet the boys at the hobby store will be impressed about my 'cheep Chinese' TX now.
Earl
Earl
-
- Posts: 236
- Joined: Tue Dec 27, 2011 11:19 pm
- Country: -
- Location: Don Mills, Ontario
Re: DSM2 work
The "chirp" comes from the beeper in the DX4e, not the module.cr8tive_leo wrote:Good to know.
Thanks, you saved a life today.
Doesn't help when the manual states when goin into dsmx mode it should chirp.
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
yes, that's what I am using though. a dx4e. with the module in it.. I tested it with the ar9000, and it works (remember the issue I had about the channel jitter) so it's not the ar9000's I have.
WIll be ripping it apart (still no dsx mode) *shrugs* and see if it still works with the ar9000. I am not giving up.
Soo our wonderfull little boxes will chirp, sing, complain about the flying weather.. etc...
WIll be ripping it apart (still no dsx mode) *shrugs* and see if it still works with the ar9000. I am not giving up.
Soo our wonderfull little boxes will chirp, sing, complain about the flying weather.. etc...
-
- Posts: 236
- Joined: Tue Dec 27, 2011 11:19 pm
- Country: -
- Location: Don Mills, Ontario
Re: DSM2 work
I think the online manual might have the stick directions for entering DSM2 only and DSMx backwards.
Re: DSM2 work
I will try reversing the control on power up and see what happens.
Earl
Earl
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
I have a printed manual.. in 13 different languages...pmackenzie wrote:I think the online manual might have the stick directions for entering DSM2 only and DSMx backwards.
Says the same thing in English, German, French, Spanish, Italian and Polish, the Arabic looks backwards though...
Re: DSM2 work
Thats because Arabic reads right to left.....ha...ha..
Earl
Earl
Re: DSM2 work
DSM2 broke in rev 701. as soon as you set the dsm2 mode in a model, it keeps resetting...
***** reloaded software fixed problem ******
Still have the right/left direction reversed...
Earl
***** reloaded software fixed problem ******
Still have the right/left direction reversed...
Earl
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
DSM2 work
Really?
I updated, and nada, everything is cool.
Playin with micro corsair right now , setting up dual rates for everything.
---
I am here: http://maps.google.com/maps?ll=44.056229,-79.476275
I updated, and nada, everything is cool.
Playin with micro corsair right now , setting up dual rates for everything.
---
I am here: http://maps.google.com/maps?ll=44.056229,-79.476275
Re: DSM2 work
Still have the left/right reversal problem...
on my Blade mQX quad.
Earl
on my Blade mQX quad.
Earl
- Daryoon
- Posts: 60
- Joined: Sun Jan 08, 2012 5:07 pm
- Country: -
- Location: http://www.hacksmods.com
- Contact:
Re: DSM2 work
Leo: I'd be interested in your micro Corsiar eepe. I just got one in a trade and never flew a plane before. It would be good to be able to peek at your settings.
yay! I am out of moderation status.
ABBC3_OFFTOPIC
Also, when is this moderation for new users going to end. It's really preventing me from joining the discussion.
- wheelspinner20
- Posts: 175
- Joined: Tue Dec 27, 2011 6:22 pm
- Country: -
- Location: Michigan, U.S.
Re: DSM2 work
Hi daryoon, welcome, glad you got out of probation.... !
Pat
Pat
no more quippy little latin phrases.! Its old
-
- Posts: 236
- Joined: Tue Dec 27, 2011 11:19 pm
- Country: -
- Location: Don Mills, Ontario
Re: DSM2 work
Could you explain this a bit more?uphiearl wrote:Still have the left/right reversal problem...
on my Blade mQX quad.
Earl
Reversing the servo output for the aileron channel is pretty much exactly the same as moving the stick the other way.
You could also do it by changing the sign of the mix%, but again that should be the same as using the INV function on the limits screen.
(Both at the same time will cancel each other.)
If the mQx can fly with the BNF transmitter then there is no reason it should not work correctly with the 9X.
Pat MacKenzie
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: DSM2 work
Daryoon: For surely. I will post it in teh templates tomorrow morning (off to the hospital with wifey, she;s ill. )
Re: DSM2 work
Thats what I thought also Pat but the inv does not seem to do a thing on the quad in the X configuration. I will try to put it into the + configuration and see if it helps. Also the YAW is reversed.
Earl
Earl
Re: DSM2 work
YEA !!!! using - on the mixes for YAW and ALE changed direction to correct orientation ! The INV do NOT do it.
Thanks PAT.
Earl
Thanks PAT.
Earl