When trying to flash, please add -B 100 on the AvrDude command line. This slows the programming speed down and may let the flash operation work.
Do NOT use the -F option.
Mike.
Problem with last new Hobbyking Turnigy 9X transmiters.
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
Some time ago, with the M128 processor, I had the hard reproduceable error 0102 when the throttle cut switch was in the up position.
Check that this is not your problem.
Reinhard
Check that this is not your problem.
Reinhard
-
- Posts: 2
- Joined: Sat Nov 25, 2017 7:08 am
- Country: -
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
Hi,
thanks for the support, the -B 100 solved the writing problem.
thanks for the support, the -B 100 solved the writing problem.
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
Hello everyone,
Just signed up to this forum to say that flashing the Turnigy 9X with the GREEN ED0040502-H16D 1105 chip with the ER9X for Mega128 firmware with eepe works. I used a SmartieParts SP Basic board plugged in to a MacBook Air to do so.
For anyone using this setup: you will need to install Homebrew and AVRDUDE using the terminal.
I'd like to thank all the participants in this thread because it is litterally the only place on the net you can find info regarding the cloned chip.
I'd also like to mention that I first intended to use OpenTx, and used Companion 2.1.9 to flash but the software couldn't recognize the chip and was sending back errors.
Thanks,
L
Just signed up to this forum to say that flashing the Turnigy 9X with the GREEN ED0040502-H16D 1105 chip with the ER9X for Mega128 firmware with eepe works. I used a SmartieParts SP Basic board plugged in to a MacBook Air to do so.
For anyone using this setup: you will need to install Homebrew and AVRDUDE using the terminal.
I'd like to thank all the participants in this thread because it is litterally the only place on the net you can find info regarding the cloned chip.
I'd also like to mention that I first intended to use OpenTx, and used Companion 2.1.9 to flash but the software couldn't recognize the chip and was sending back errors.
Thanks,
L
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
So I'm, for what I have read, there is no solution for this green chip 9x boards with the 9xtreme.
I added this board, but this switch error shows up.
at power on it seemed to flash the firmware, but then the error show on the screen.
one can hear the welcome message though.
I added this board, but this switch error shows up.
at power on it seemed to flash the firmware, but then the error show on the screen.
one can hear the welcome message though.
- Attachments
-
- IMG_20220720_212717830~2.jpg
- (900.66 KiB) Not downloaded yet
-
- IMG_20220720_213025797~3.jpg
- (639.07 KiB) Not downloaded yet
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
The 9Xtreme is not managing to flash the firmware to the "Green" cpu.
What do the backlight colours show during power on. They go through a specific sequence indicating how the flashing is progressing, and whether it completes successfully.
Mike
What do the backlight colours show during power on. They go through a specific sequence indicating how the flashing is progressing, and whether it completes successfully.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
The first time, there a was sequence alright, but I don't remember what was because it was a bit fast. Then it went to the switch error screen.
Now everytime I power on the radio, that screen shows up.
Edit:
Every time I unplug the battery and plug it again and turn on the radio, I see that the flash attempt occurs again, but with the same result at the end. I will record it and upload the video.
Now everytime I power on the radio, that screen shows up.
Edit:
Every time I unplug the battery and plug it again and turn on the radio, I see that the flash attempt occurs again, but with the same result at the end. I will record it and upload the video.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
Hi Mike, after watching closely, I realised that the situation is straight forward. What happens, is that the screen changes color several times and ends with a red light. Which probably means that it failed to flash. You probably noticed above. There is this user that says it is possible to flash with the smartieparts parts programmer with er9x.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
This is the firmware that is flashed to the AVR processor (same for '64 and '128).
Mike
Mike
- Attachments
-
- slave64.zip
- (2.71 KiB) Downloaded 125 times
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Problem with last new Hobbyking Turnigy 9X transmiters.
I dont know what have i done, but suddenly it started working fine. I copied that file to the firmware folder, but didnt flashed it, so i assume the 9xtreme flashed it.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.