9x been modded

[Blackdog]

Hi any one any idea what's been done to this transmitter

[ShowMaster]

Wow what a mess. The white board is a smartipsrts board designed to flash the much processor with upgraded firmware like er9x. It also adds a backlight.
Not sure what the sparkfun board does but maybe it’s fixing a usb connection the smartiparts boars comes with?
This sp board and er9x firmware adds telemetry display the the screen from a Frsky D receiver.
http://smartieparts.com/shop/index.php? ... cts_id=331

The diode and other parts higher on the switch boars was to modify the beeper circuit.

More mods info

https://www.rcgroups.com/forums/showthr ... R9X-OpenTX

https://openrcforums.com/forum/viewforum.php?f=71


The second picture is showing a internal installed Frsky dht solder in module. This 2.4g module supports telemetry from the D receiver to the SP board.
No idea why a external DJT Frsky module wasn’t used unless it left the back case port open for other module options.



Sent from my iPhone using Tapatalk Pro

[jhsa]

I can't see an antenna connected to the module???

João

Sent from my BLN-L21 using Tapatalk

[bob195558]

WOW ! how things have changed in just a few years.

I still have one 9x with Steven's 9x SP 9x Programmer (Rev 2.3)
board and with the 9x TelemetrEZ (Rev 1.0) board.
I have always run the telemetry wires through the back of the radio case
to the FrSky transmitter too.

I have several old un-used SP 9x Programmer boards from
upgrading 9x radios to the 9XTreme boards, which are sold out.
Wish 9XTreme boards were still available.

[jhsa]

WOW ! how things have changed in just a few years.

You haven't noticed that? Since years I have a stock 9x board with a better processor, rotary encoder, more switches, backlight, voice module that also saves models to the SD card, internal DHT module, but I would probably replace it with a MultiProtocol module as it is supported by Er9x, etc, etc.

João

[bob195558]

I fell asleep and while I was sleeping I was dreaming about 3D Printing with a CR10 printer.

3D Printing 9x Radio with erSky9x !

[bob195558]

Cold and Snowing today in New England

Update: I have 12 inches of new snow (so far) at 4:30 pm.
Still snowing.

[MikeB]

I think the red, Sparkfun board is a level converter for the telemetry connection to/from the DHT module.

Mike

[jhsa]

Didn't the SP board have the converter already on it?

João

[bob195558]

If I remember correctly, you could do your own upgrade to have Telemetry
or purchase from Steven, his plug and play 9x TelemetrEZ board,
which was much easier to install.

The SP board did the USB Program flashing and the Back Light for the display.
More about the (Rev 2.3: White board. Now includes header and plug/wires for LED connection
and Header for possible future use with TelemetrEZ added.)
Smartieparts.com: (http://smartieparts.com/shop/index.php? ... cts_id=331).

Discontinued SP Products: (https://smartieparts.com/shop/index.php ... ex&cPath=9).
Take a trip down memory lane.

(http://smartieparts.com/shop/)


Some more old 9Xtreme board info here: (https://openrcforums.com/forum/viewtopi ... =95&t=7182).

[topdiggy2]

WOW ! how things have changed in just a few years.

I still have one 9x with Steven's 9x SP 9x Programmer (Rev 2.3)
board and with the 9x TelemetrEZ (Rev 1.0) board.
I have always run the telemetry wires through the back of the radio case
to the FrSky transmitter too.

I have several old un-used SP 9x Programmer boards from
upgrading 9x radios to the 9XTreme boards, which are sold out.
Wish 9XTreme boards were still available.

Hello Bill -

Thanks for your post...i recently purchased one of these FlySky FS-TH9x. Im new to RC building my first drone for aerial photo. Anyways, i was wondering if you wanted to sell one of those 9Xtreme boards or program cables.?

[bob195558]

See here about 9xtreme boards that are not assembled: https://openrcforums.com/forum/viewtopi ... 60#p147801

[BiggsDarklighter]

Thanks for your post...i recently purchased one of these FlySky FS-TH9x. Im new to RC building my first drone for aerial photo. Anyways, i was wondering if you wanted to sell one of those 9Xtreme boards or program cables.?

topdiggy2 these are the only ones still avalible. If you need ready made, this is where it is at.
https://smartieparts.com/shop/index.php ... e5nhv06665

[tedbmoss]

This is an early Smartie Parts mod to allow reprogramming with out to much soldering. The internal FrSky Tx module has been added or a standard module has been modified and at a guess a further mod has been made to add sound. there was some problems with telemetering which may have been corrected with the Spark-fun board, it is not possible to tell from here , perhaps someone else will know. You should put this in Turnigy 9x instead of th9x it is an obscure place and may not be seen. I did not see all the other answers when I posted this.