X9D - Stuttering Noise and no startup
X9D - Stuttering Noise and no startup
When i tried to switch on my X9D, all I got is flashing of the screen with some ‘stuttering’ noise, but Taranis Will not start up. See attached video.
I tried disconnecting battery and the module in backboard but no help there.
Suggestions?
When starting up in resetmode, screen works normal. When I exit, noise begins Alain. I tried disconnecting battery and the module in backboard but no help there.
Suggestions?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X9D - Stuttering Noise and no startup
Has this just starting to happen, or have you done any firmware updates?
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X9D - Stuttering Noise and no startup
Just like that. (Have to say I bought it second hand). Worked for two days and then gave me this when I started it up the third time.
Re: X9D - Stuttering Noise and no startup
Make sure your SD card located in the battery compartment is fitted properly...
Sent from my LM-Q710.FGN using Tapatalk
Sent from my LM-Q710.FGN using Tapatalk
Re: X9D - Stuttering Noise and no startup
Tried SD card, but did not help.
Re: X9D - Stuttering Noise and no startup
Might be worth trying to reflash the firmware.
Re: X9D - Stuttering Noise and no startup
Seems there is not enough space on SD card. Will have to buy bigger one for that...
Re: X9D - Stuttering Noise and no startup
Take the SD card from the Taranis. Backup the card content on your computer.
Read and follow the procedure here
https://oscarliang.com/flash-opentx-firmware-taranis/
A 1GB SD card is totally sufficient for use.
br
Re: X9D - Stuttering Noise and no startup
Flashing did not help...
Re: X9D - Stuttering Noise and no startup
Also did the complete Oscar Liang works (Open tx), but also no help there. Something else broken?
Re: X9D - Stuttering Noise and no startup
Yeah, really sounds like there's a hardware fault.
Re: X9D - Stuttering Noise and no startup
But isn’t it strange then that the screen works perfectly on the set-up screens? (I used them to flash it).
Could TX module cause this?
Could TX module cause this?
Re: X9D - Stuttering Noise and no startup
Does someone have another suggestion?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X9D - Stuttering Noise and no startup
You could try flashing ersky9x and see if that is any different.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: X9D - Stuttering Noise and no startup
Can find ersky9x here: (http://www.er9x.com/).
I use ersky9x on my Taranis and like it a lot.
I use ersky9x on my Taranis and like it a lot.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: X9D - Stuttering Noise and no startup
Ok. Will try this and keep you posted.
Re: X9D - Stuttering Noise and no startup
This happened to my X9D SE. Sent it to Aloft, and they replaced the mainboard, after I tried most of the fixes listed above.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: X9D - Stuttering Noise and no startup
So you still have the same problem after Aloft fixed it ?
Last edited by bob195558 on Fri May 03, 2019 3:21 pm, edited 2 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).