9XR Pro + Multiiprotocol + Inductrix FPV
9XR Pro + Multiiprotocol + Inductrix FPV
Hello, need some help, I have a bnf fpv inductrix and I just got the 4n1 module and I get it to bind finally. However, it will not move. Nothing I do to the control results in any action from the drone. I have my settings for the mutli protocol dsm(DSMX-22, autobind =y, 8ch, rxnum8, trainer polarity pos, power=high, rate 7ms, 1st chan=6, module tx and rx nodes on the board are bridged.
Please help...
Please help...
- MikeB
- 9x Developer
- Posts: 18010
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Why first chan = 6? Try setting this back to 1.
If first chan is set to 6, then the mixer channels 1 to 5 are not being used, channel 6 is sent as channel 1 to the module.
Mike.
If first chan is set to 6, then the mixer channels 1 to 5 are not being used, channel 6 is sent as channel 1 to the module.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: RE: Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Thx, I will check that when I get home. And again for being patient I'm new to all this..MikeB wrote:Why first chan = 6? Try setting this back to 1.
If first chan is set to 6, then the mixer channels 1 to 5 are not being used, channel 6 is sent as channel 1 to the module.
Mike.
Sent from my SM-G920V using Tapatalk
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Mike, I changed it to ch1 and it seems to bind but the controls are wonkie.
Re: RE: Re: 9XR Pro + Multiiprotocol + Inductrix FPV
it does seem to turn on the motors atleastairwolfe wrote:Mike, I changed it to ch1 and it seems to bind but the controls are wonkie.
Sent from my SM-G920V using Tapatalk
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Everything is in reverse. my right sticket controls the throttle to some degree but only at a angle.(bottom left) which also activates the drone.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Please check your channel order: 1=T, 2=A, 3=E, 4=R, 6=Mode
I am using a taranis with a old DX4 module, so it might be different to your setup. But this is the way it works for me. You can also search for a NanoQX setup, as it is the same configuration.
Lutz
I am using a taranis with a old DX4 module, so it might be different to your setup. But this is the way it works for me. You can also search for a NanoQX setup, as it is the same configuration.
Lutz
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
If he is using the 4 in 1 multi module, I believe the channel order should be AETR?
Also what stick mode do you fly? Is your throttle on the left, or on the right?
João
Also what stick mode do you fly? Is your throttle on the left, or on the right?
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Yes, multimodule needs AETR.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
my throttle is on the left. mode2 however I had to change it to mode 1 to make the drone work correctly some what.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
That will work but is not correct, you should leave it in mode 2 and change ordering in the mixer.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
ooh ok, I will do that. I got it to fly but its like on the throttle there is a dead spot and its not all the way down. All the way down goes in reverse... when I get home I will work on it some more.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Did you calibrate your radio's sticks?
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: RE: Re: 9XR Pro + Multiiprotocol + Inductrix FPV
I believe so but I will do that again when I get home. Thx for the help.jhsa wrote:Did you calibrate your radio's sticks?
João
Sent from my SM-G920V using Tapatalk
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
I also noticed this behavior on the throttle channel. I had to raise the min value quite a lot.airwolfe wrote:ooh ok, I will do that. I got it to fly but its like on the throttle there is a dead spot and its not all the way down. All the way down goes in reverse... when I get home I will work on it some more.