9XR PRO FRSKY Telemetry
Re: 9XR PRO FRSKY Telemetry
Dear Mike
The radio is 9XR Pro. The module is XJT. And the RX is X8Rs. The firmware version is ersky9x-R214.
Something strange is going on. Because everything was normal and suddenly I no longer have any telemetry information. When do the range check "in the protocol menu" to RSSI information is zero, and the RX operate normally. See the photos.
best regards
Victor
The radio is 9XR Pro. The module is XJT. And the RX is X8Rs. The firmware version is ersky9x-R214.
Something strange is going on. Because everything was normal and suddenly I no longer have any telemetry information. When do the range check "in the protocol menu" to RSSI information is zero, and the RX operate normally. See the photos.
best regards
Victor
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
In the TELEMETRY menu, check that:
FrSky Com Port is set to 1
and:
Invert COM 1 is set to OFF
Mike.
FrSky Com Port is set to 1
and:
Invert COM 1 is set to OFF
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9XR PRO FRSKY Telemetry
dear Mike
I was in this setting. Yet still not working. There are some procedures that I can try?
Thank you for your attention.
I was in this setting. Yet still not working. There are some procedures that I can try?
Thank you for your attention.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
One more setting to check, at the top of the Telemetry menu, check that UsrProto is set to FrHub.
I'll try to load r214 back on my Tx and test it. r217 is the latest revision, and that's what I'm running, or testing the next one after that!
Mike.
I'll try to load r214 back on my Tx and test it. r217 is the latest revision, and that's what I'm running, or testing the next one after that!
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9XR PRO FRSKY Telemetry
Is there any chance that I can try to reestablish telemetry? no longer know what to do.I do not understand. because everything was normal and suddenly stopped working. thanks for your attention
Re: 9XR PRO FRSKY Telemetry
The Usrproto is Frhub.
Is there any chance that I can try to reestablish telemetry? no longer know what to do.I do not understand. because everything was normal and suddenly stopped working. thanks for your attention
Victor
Is there any chance that I can try to reestablish telemetry? no longer know what to do.I do not understand. because everything was normal and suddenly stopped working. thanks for your attention
Victor
Re: 9XR PRO FRSKY Telemetry
Dear Mike
I found the problem!I managed to solve. It was simple. Were the keys that are behind the Frsky module that were in the wrong position. I put in the correct position and returned everything to normal. Anyway, thank you for your attention.
Victor
I found the problem!I managed to solve. It was simple. Were the keys that are behind the Frsky module that were in the wrong position. I put in the correct position and returned everything to normal. Anyway, thank you for your attention.
Victor
-
- Posts: 2
- Joined: Tue Jun 02, 2015 3:41 am
- Country: -
Re: 9XR PRO FRSKY Telemetry
I think I am going to have to jump in on this thread. I've been trying so hard to get this working without having to bother anyone.
I have a 9xr Pro, FrSKY DJT Module, I have the telemetry cable (one end is plugged into the futaba port) the other end is plugged into DJT module Grey is in Rxd, white is in Txd.
I have a FrSky D8R-II Plus, I have the jumper across A1 & x (default). The D8R-II has all 8 signal wires connected to the FCB and only the GND and + from channel 1 connected (I don't believe this is relevant here)
I have upgraded my firmware on the 9xr pro
Vers: v110-Mike
SVN: ersky9x-r217
MOD:REVB-s
I have gonr into the Telemetry screen and set A1 to 13.2v. FrHub is selected.
FrSKY Com port is set to 1
invert Com 1 is off
Any thoughts? I would love to see that number next to A1 move.
Thanks
I have a 9xr Pro, FrSKY DJT Module, I have the telemetry cable (one end is plugged into the futaba port) the other end is plugged into DJT module Grey is in Rxd, white is in Txd.
I have a FrSky D8R-II Plus, I have the jumper across A1 & x (default). The D8R-II has all 8 signal wires connected to the FCB and only the GND and + from channel 1 connected (I don't believe this is relevant here)
I have upgraded my firmware on the 9xr pro
Vers: v110-Mike
SVN: ersky9x-r217
MOD:REVB-s
I have gonr into the Telemetry screen and set A1 to 13.2v. FrHub is selected.
FrSKY Com port is set to 1
invert Com 1 is off
Any thoughts? I would love to see that number next to A1 move.
Thanks
Re: 9XR PRO FRSKY Telemetry
If you are using the telemetry cable try setting the COM port to 2.
By the way, you don't bother anyone here. If you have a problem please post it. We are happy to help if we can, and might save you a headache
João
EDIT: Just a little note. When A1 has the jumper it will measure the receiver voltage. That is fine if the battery is directly connected to the receiver. If you have the receiver powered by a BEC that measurement is useless as the battery could be fully discharged and the receiver still gets its 5V.
In this case for measuring the battery voltage you need an external voltage sensor..
By the way, you don't bother anyone here. If you have a problem please post it. We are happy to help if we can, and might save you a headache
João
EDIT: Just a little note. When A1 has the jumper it will measure the receiver voltage. That is fine if the battery is directly connected to the receiver. If you have the receiver powered by a BEC that measurement is useless as the battery could be fully discharged and the receiver still gets its 5V.
In this case for measuring the battery voltage you need an external voltage sensor..
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 2
- Joined: Tue Jun 02, 2015 3:41 am
- Country: -
Re: 9XR PRO FRSKY Telemetry
João
Thanks so much for the response. It just needed to be changed to com 2, as you mentioned. So that is awesome.
You were right about the voltage being 5v because it's coming from a BEC. I am new to all of this, but in the back of my mind I thought that may be the case. My FCB has a battery monitor on it, when I hook up a computer to it, I can see the battery voltage. I thought there might be some way to get that into A2 on the receiver. But now I believe that the battery monitor on the FCB is only good for use internally, for like setting off the buzzer that can be attached to the board. Which all makes perfect sense to me now.
Can anyone recommend an external voltage sensor for the setup I listed above? Or is it one of those things where they are all pretty much the same and just get one.
Thanks so much for the response. It just needed to be changed to com 2, as you mentioned. So that is awesome.
You were right about the voltage being 5v because it's coming from a BEC. I am new to all of this, but in the back of my mind I thought that may be the case. My FCB has a battery monitor on it, when I hook up a computer to it, I can see the battery voltage. I thought there might be some way to get that into A2 on the receiver. But now I believe that the battery monitor on the FCB is only good for use internally, for like setting off the buzzer that can be attached to the board. Which all makes perfect sense to me now.
Can anyone recommend an external voltage sensor for the setup I listed above? Or is it one of those things where they are all pretty much the same and just get one.
Re: 9XR PRO FRSKY Telemetry
With my Flip32 i'm getting the battery voltage on the variable "ctot" without using an external sensor. Is that variable showing no values on your TX?
-
- Posts: 20
- Joined: Sun Sep 20, 2015 4:56 am
- Country: Australia
Re: 9XR PRO FRSKY Telemetry
Just a quick question, with all these settings, in the correct order and firmware etc. will the Signal strength be displayed on a OSD ? I have the main battery displaying, but would like signal strength as well, must I have the external cable for that or is that not necessary? most fascinating following all these questions and answers. thanks
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
I'm not sure I fully understand the question!
By main battery do you mean the Tx battery or the one on the aircraft?
By OSD, do you mean the display on the Tx or one somewhere else?
Mike.
By main battery do you mean the Tx battery or the one on the aircraft?
By OSD, do you mean the display on the Tx or one somewhere else?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
-
- Posts: 20
- Joined: Sun Sep 20, 2015 4:56 am
- Country: Australia
Re: 9XR PRO FRSKY Telemetry
Sorry Mike I am getting the aircraft battery voltage from the vbat connection on the naze32 through a micro minim osd to my goggles. The OSD is for the goggles not the tx. I am still very much a beginner so wasnt sure what the cable {futaba ?} will actually show on my quanum V2 goggles and if it is worth getting one or not. I dont know what telemetry will be sent or displayed. Thanks again for the wealth of knowledge
Re: 9XR PRO FRSKY Telemetry
Hi all
Can any1 help me..i have 9xrpro+xjt module+x4r rx and i dont know how to setup the telemetry..trying all the step on previous post and only the rssi working on my transmitter..flash new version ersky9x r218..i hope some1 can guide me..many thanks..
Can any1 help me..i have 9xrpro+xjt module+x4r rx and i dont know how to setup the telemetry..trying all the step on previous post and only the rssi working on my transmitter..flash new version ersky9x r218..i hope some1 can guide me..many thanks..
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
The XJT connects internally for the telemetry.
You need to set the protocol to PXX (not PPM), set the type to D16, then, in the telemetry menu, set "FrSky COM port" to 1 and "Invert COM 1" to OFF.
Mike.
You need to set the protocol to PXX (not PPM), set the type to D16, then, in the telemetry menu, set "FrSky COM port" to 1 and "Invert COM 1" to OFF.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9XR PRO FRSKY Telemetry
Just change protocol to pxx and set to d16 also frskycom port to 1..still wont work for me and no rssi read on transmitter
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
Please confirm the radio is controlling servos on the receiver.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9XR PRO FRSKY Telemetry
All channel work perfect including aux
Re: 9XR PRO FRSKY Telemetry
Just telemetry wont work.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
Please try re-binding the receiver, there is a bind option in the protocol menu for this. It may be that the Rx isn't sending the telemetry data if previously bound when using PPM as the protocol.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9XR PRO FRSKY Telemetry
Thanks alot mike..now my telemetry work..but fasv show 16.2 value even im using a new battery..change another battery it still show 16.2..when im using lipo checker it show 16.8..im using 4s lipo battery..how can i fix this prob?
1 more thing how to set voice alarm when fasv hit 14.5 example and the voice tell me how much v left..is that auto remind or should i set somewhere else
thanks alot mike for u help..sry for noob english
1 more thing how to set voice alarm when fasv hit 14.5 example and the voice tell me how much v left..is that auto remind or should i set somewhere else
thanks alot mike for u help..sry for noob english
Re: 9XR PRO FRSKY Telemetry
Watch the following videos.. They explain how to program voice events..
https://www.youtube.com/watch?v=TW9Bdro ... 9&index=10
https://www.youtube.com/watch?v=pq3XGli ... 9&index=11
https://www.youtube.com/watch?v=6WRosEf ... qcuIqJXhb9
https://www.youtube.com/watch?v=TW9Bdro ... 9&index=10
https://www.youtube.com/watch?v=pq3XGli ... 9&index=11
https://www.youtube.com/watch?v=6WRosEf ... qcuIqJXhb9
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
Ersky9x just reports the voltage as sent by the sensor. You have two measurements that differ, we don't actually know if the Fasv is wrong, or the lipo checker is wrong, or both are wrong!Hiodo wrote:Thanks alot mike..now my telemetry work..but fasv show 16.2 value even im using a new battery..change another battery it still show 16.2..when im using lipo checker it show 16.8..im using 4s lipo battery..how can i fix this prob?
If the Fasv value is that far out, you could use a "Scaler" to correct the reading. To do so will need investigation to discover if the Fasv value is reading 0.6V low all the time, or is just reading a few percent low.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9XR PRO FRSKY Telemetry
Thanks for replying..thats video helps alot..but i have prob that i cant see any wav file on voice alarm..download new voice pack for ersky9x..on sd card all file is there..i only can use the number file..cant use name file..
and 1 more thing when i set voice alarm for fasv when it hit 14.7 example,the alarm just said said what i set only..no voice for how many V left..how do i fix this..thanks alot
and 1 more thing when i set voice alarm for fasv when it hit 14.7 example,the alarm just said said what i set only..no voice for how many V left..how do i fix this..thanks alot
Re: 9XR PRO FRSKY Telemetry
Probably because you didn't install the voice pack correctly.
You should have a folder named "voice" on your SD Card. Then inside the voice folder other 3 folders.
"system, user and modelNames".
João
You should have a folder named "voice" on your SD Card. Then inside the voice folder other 3 folders.
"system, user and modelNames".
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: 9XR PRO FRSKY Telemetry
Non-telemety newbie question here; do I have to have the separate FrSky screen to display telemetry or can I just use the 9XR Pro screens? I'm getting ready to purchase the FrSky module for my tx and am doing a little research beforehand. Glad I found this site. Which module should I go for, the DJT or the XJT?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
The 9XR-PRO is able to display the telemetry on it's own screen, and also includes voice alerts you may set based on telemetry values.
The XJT is directly supported, the DJT requires the extra cable to connect it in.
The XJT is also the more recent module.
Mike.
The XJT is directly supported, the DJT requires the extra cable to connect it in.
The XJT is also the more recent module.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9XR PRO FRSKY Telemetry
Another newbie with a 9xr-Pro...trying to get my Motor Battery Voltage to show up on the telemetry screen...without success so far.
Firmware is ErSky9x-r218. Vers= V.3527-Mike. Mod=REVB-X
Transmitter module is XJT (both dip switches off)
Receiver is X4R
No jumper cable on back of transmitter (using com port 1...invert com 1 is off)
I have telemetry working showing RSSI and TSSI (Hooray!!!)
Also, in the plane, I have FrSky Battery Voltage Sensor (FBVS-01) hooked up to Motor battery (+) to AIN of receiver smart port connector and Motor battery (-) to (-) black wire of smart port connector. (connection is same as image shown on x4r instructions). I believe this is analog connection.
On telemetry screen A1, A2, A3, FasV, cVolt, cTot all showing 0.0v
How do I see Motor battery telemetry from FBVS-01 on 9xr-Pro ?
Many thanks for your help !!
Firmware is ErSky9x-r218. Vers= V.3527-Mike. Mod=REVB-X
Transmitter module is XJT (both dip switches off)
Receiver is X4R
No jumper cable on back of transmitter (using com port 1...invert com 1 is off)
I have telemetry working showing RSSI and TSSI (Hooray!!!)
Also, in the plane, I have FrSky Battery Voltage Sensor (FBVS-01) hooked up to Motor battery (+) to AIN of receiver smart port connector and Motor battery (-) to (-) black wire of smart port connector. (connection is same as image shown on x4r instructions). I believe this is analog connection.
On telemetry screen A1, A2, A3, FasV, cVolt, cTot all showing 0.0v
How do I see Motor battery telemetry from FBVS-01 on 9xr-Pro ?
Many thanks for your help !!
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9XR PRO FRSKY Telemetry
On the telemetry menu, have you set the scaling for A1 and or A2? Usually you need to set it to about 13.2V.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!