HK450 Heli with very soft start (HK ESC). Plus sw warnings.
HK450 Heli with very soft start (HK ESC). Plus sw warnings.
This template demonstarte how to apply soft start, if not supported own ESC.
Warning signal on, if throttle cut active but flight mode switch not ID0.
Warning signal on, if Gyro not switched headlock mode.
Original source: random sweep.
ch1,2,3 = AIL, ELE, PIT servos
ch4 = rudder servo (to GYro in)
ch5 = THR (ESC)
ch6 = Gyro sensitivy
ID0= 1 idle0, -2° pith hold, cyclic is normal (c1,c4) (if c4 and c1 curve modify the flmode is normal for idle0) (pitch curve= c4)
ID1 =1 idle1, curve (c2) (pitch curve= c5)
ID2 = 1 idle2, curve (c3) (pitch curve= c6)
THR switch = Throttle cut.
ch11 pitch servo (virtual channel)
if gear=1 (rate mode) then warning audio.
if THR sw=0 and id1 or id2=1 then warning soud active (motor off but flight mode not id0)
if ID0=1 and THR switch=1 then ignition (slow start).
modify ch1,2,3 and ch11 to collective and ciclyc pitch.
ch15, ch16, sw1, sw2 = soft start slave ch and sw
sw3, sw4, sw5 = warning sign switch (idle0,1,2)
Warning signal on, if throttle cut active but flight mode switch not ID0.
Warning signal on, if Gyro not switched headlock mode.
Original source: random sweep.
ch1,2,3 = AIL, ELE, PIT servos
ch4 = rudder servo (to GYro in)
ch5 = THR (ESC)
ch6 = Gyro sensitivy
ID0= 1 idle0, -2° pith hold, cyclic is normal (c1,c4) (if c4 and c1 curve modify the flmode is normal for idle0) (pitch curve= c4)
ID1 =1 idle1, curve (c2) (pitch curve= c5)
ID2 = 1 idle2, curve (c3) (pitch curve= c6)
THR switch = Throttle cut.
ch11 pitch servo (virtual channel)
if gear=1 (rate mode) then warning audio.
if THR sw=0 and id1 or id2=1 then warning soud active (motor off but flight mode not id0)
if ID0=1 and THR switch=1 then ignition (slow start).
modify ch1,2,3 and ch11 to collective and ciclyc pitch.
ch15, ch16, sw1, sw2 = soft start slave ch and sw
sw3, sw4, sw5 = warning sign switch (idle0,1,2)
- Attachments
-
- HELI450_very_slow_start_(HK ESC).eepe
- (4.84 KiB) Downloaded 1032 times
Last edited by njozsef on Sun Jul 08, 2012 8:23 pm, edited 1 time in total.
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin
valid (flying and fine tuned) ALIGN 450 setup
please check and fix the limits, trim, throttle curves, pitch curves, subtrim and rudder direction.
switch:
id0=ignition start mode
id1 id2 3d setup middle and high rpm.
thottle cut= motor on/off
elev and ail= low/mid/high expo
gear=gyro mode rate/headlock
trainer= light on
cv1= start throttle curve
cv2, cv3 = id0, 1 throttle curve
cv4,5,6 = id1,2,3 pitch curve
please check and fix the limits, trim, throttle curves, pitch curves, subtrim and rudder direction.
switch:
id0=ignition start mode
id1 id2 3d setup middle and high rpm.
thottle cut= motor on/off
elev and ail= low/mid/high expo
gear=gyro mode rate/headlock
trainer= light on
cv1= start throttle curve
cv2, cv3 = id0, 1 throttle curve
cv4,5,6 = id1,2,3 pitch curve
- Attachments
-
- real_HELI450_very_slow_start_(HK ESC).eepe
- (4.84 KiB) Downloaded 935 times
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin
Hello,
I'm a beginner on CP helis,
I try to programm my T9x for a 450 3D heli, evrything looks good so far, only pitch has to be converted.
How can I do this, must I reverse al 3 servos ?
I'm a beginner on CP helis,
I try to programm my T9x for a 450 3D heli, evrything looks good so far, only pitch has to be converted.
How can I do this, must I reverse al 3 servos ?
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin
My main problem is which servo is aileron/elevator/pitch ?
I mean which servo is cyc1/2/3 on my 120 deg swash plate ?
I have ER9x
I mean which servo is cyc1/2/3 on my 120 deg swash plate ?
I have ER9x
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin
This attachments working for trex (or clone) 450 heli.
Please download.
please settings the
heli swash type on heli menu.
Please download.
please settings the
heli swash type on heli menu.
-
- Posts: 32
- Joined: Fri Jun 22, 2012 5:21 am
- Country: -
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin
Do you have the file so I can open it up on the Mac version of this software? I have windows on my mac as well, I just prefer not to do anything in that OS
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin
The file is the same whether you use the Win, mac or linux version of eepe.
If you use eepe you'd better use the Windows version, as the Mac version is outdated and doesn't support the current er9x revision. If you use companion9x both versions are in sync.
If you use eepe you'd better use the Windows version, as the Mac version is outdated and doesn't support the current er9x revision. If you use companion9x both versions are in sync.
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnings.
:HK450 Heli with very soft start (HK ESC). Plus sw warnings.:
I flashed your eepe everything seems to do the right move except my motor it dont turn on. My 450 Esky belt cp version 1 I have been racking my brain for 2 days Im to close can you maybe give me some ideas were it may be failing or what is in the wrong place?
I flashed your eepe everything seems to do the right move except my motor it dont turn on. My 450 Esky belt cp version 1 I have been racking my brain for 2 days Im to close can you maybe give me some ideas were it may be failing or what is in the wrong place?
Last edited by silversurfer48 on Sat Apr 09, 2016 6:38 am, edited 1 time in total.
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnings.
The original post says the THR switch is "Throttle cut". Just checking you have your THR switch in the correct direction.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: HK450 Heli with very soft start (HK ESC). Plus sw warnings.
That file is 4 years old, for a plain 9x, and we don't even know for what firmware. It could be horribly broken on whatever current software you're trying to use it with. Actually it won't even open with eepskye set to 9Xtreme, so as I believe that's the radio you have I don't even know how you get anything to work.
Please be careful, helis can bite badly and it takes care to get everything right. Don't do anything you don't understand.
Please be careful, helis can bite badly and it takes care to get everything right. Don't do anything you don't understand.