Hello everyone!
I have a little issue. My "platform" is:
- Taranis X7 Q , just updated OpenTX firmware from 2.3.9 to 2.3.10;
- fc Mateksys F722-SE programmed with Betaflight
After updated opentx firmware I checked about AETR1234 protocol on the F722-SE and the order of channels into the taranis and the order is the same as like as it is settled on the fc.
To check everything I do:
- from Betaflight's motor test I check motors are working
- from Betaflight's Receiver I check throttle stick and I see the progress bar increasing/decreasing depending between -987 and +987 on what I want to do but I see also blue light on the fc blinking up so I go back to Motor Test and I try to arm uav but in fact I see throttle doesn't rise motors up at least at minimum and I see the blue led blinking up
I detached cable and I tried to gas motors from receiver and they doesn't rise up.
Considering channels are OK and before upgrade firmware it was ok (I did a backup of settings in Open Companion and then re-settled back after firmware update so it should be as like as it was before update), I am here asking all you if are there any differences between opentx 2.3.9 and 2.3.10 that would have messed throttle up?
I can provide more informations if needed....
Thanks to all and stay safe!
Cheers!
Jadawin
Taranis X7Q doesn't give gas
Re: Taranis X7Q doesn't give gas
If the bars move correctly on the receiver tab then the radio side of things is fine, you've got something wrong in BF configuration.
Re: Taranis X7Q doesn't give gas
Hello Kilrah,
I tried whatever I could do to make motors start, I tried also to create a new model profile in taranis to set clear ranges and also I tried to reset betaflight to default settings and settled everything again with care to be sure they should follow Taranis on min 1000 - mid 1500 - max 2000 range but when I arm quad then I try to rise throttle up , the FC's blue led goes start blinking... as you an see in attached images , do you have a possible suggest to check at ?
I tried whatever I could do to make motors start, I tried also to create a new model profile in taranis to set clear ranges and also I tried to reset betaflight to default settings and settled everything again with care to be sure they should follow Taranis on min 1000 - mid 1500 - max 2000 range but when I arm quad then I try to rise throttle up , the FC's blue led goes start blinking... as you an see in attached images , do you have a possible suggest to check at ?
- Attachments
-
- taranis_telemetry.jpg
- (335.77 KiB) Not downloaded yet
-
- taranis_outputs.jpg
- (391.83 KiB) Not downloaded yet
-
- taranis_mixer.jpg
- (344.2 KiB) Not downloaded yet
-
- taranis_inputs.jpg
- (370.79 KiB) Not downloaded yet
-
- bf_setup_page.jpg
- (351.48 KiB) Not downloaded yet
-
- bf_receiver_page.jpg
- (364.6 KiB) Not downloaded yet
-
- bf_ports_page.jpg
- (296.03 KiB) Not downloaded yet
-
- bf_pid_page.jpg
- (333.92 KiB) Not downloaded yet
-
- bf_motors_page.jpg
- (299.43 KiB) Not downloaded yet
-
- bf_conf_page_4.jpg
- (374.01 KiB) Not downloaded yet
-
- bf_conf_page_3.jpg
- (278.85 KiB) Not downloaded yet
-
- bf_conf_page_2.jpg
- (289.48 KiB) Not downloaded yet
-
- bf_conf_page_1.jpg
- (326.23 KiB) Not downloaded yet