Page 1 of 1
Frsky S6R Config Software
Posted: Mon Apr 27, 2020 3:33 pm
by manesty
Hi
I have just purchased a SR6 Receiver along with a STK Dongle. I have searched the Frsky web site for a copy of the Config Software for the S6R
but an not find it, could someone please point me in the correct direction.
Google the S6R and it sends you the an older addition of the FRsky web site and you can see the Config software under the tools heading, but looking at the present Frsky websit there is no longer a Tools heading
Thanks
Re: Frsky S6R Config Software
Posted: Mon Apr 27, 2020 3:56 pm
by MikeB
Go to the download section for the S6R and download "Tool-FrSky Freelink".
Any reason not to use the script on the Tx to configure the Rx?
Mike
Re: Frsky S6R Config Software
Posted: Mon Apr 27, 2020 4:41 pm
by mak
MikeB wrote: ↑Mon Apr 27, 2020 3:56 pm
Go to the download section for the S6R and download "Tool-FrSky Freelink".
Remember to run the tool as an Administrator. Otherwise it will not run and, what worse, it will just quit with no message.
Re: Frsky S6R Config Software
Posted: Tue Apr 28, 2020 7:51 am
by manesty
Good Morning
Once again thanks for your help (ran as admin and now working OK). The receiver seems to be working, The only issue is that using the set procedure and setting channel 10 to switch between modes I can not get the receiver to stop being in the stabilisation mode I have set SA switch as a 3 position switch (up -100% Mid - 0% Down - 100%) but the receiver is always trying to stabilise ??
Re: Frsky S6R Config Software
Posted: Tue Apr 28, 2020 11:09 am
by MikeB
Assuming you are using a XJT module (internal or external) have you set the protocol to send 16 channels?
Mike
Re: Frsky S6R Config Software
Posted: Tue Apr 28, 2020 12:00 pm
by manesty
Mike
I have the receiver set up on the bench and have it bound to my Taranis X9D plus TX Each servo moves as it should.
I have S1 set to adjust the gain
SA to adjust gyro mode
SH to set urgent mode (when I toggle SH3 times the blue LED lights up on the rec)
As said when I alter SA switch the receiver stays in Gyro mode ??
Re: Frsky S6R Config Software
Posted: Tue Apr 28, 2020 6:00 pm
by MikeB
Is the S6R in "Quick Mode"?
What mixes do you have set on channel 10?
Mike
Re: Frsky S6R Config Software
Posted: Wed Apr 29, 2020 9:25 am
by manesty
Mike
I have quick mode enabled
Channel 9 set the gain (working OK)
Channel 12 works OK
not sure I have channel 10 set up correctly
MIX set as follows
CH10 SE Weight (0%) Switch (SE-) Gyro stab
+= SE Weight (-100) Switch (SE Up) Gyro S/ Level
+= SE Weight (+100) Switch (SE Down) Gyro off
Could you tell me what I should have set for the inputs ??
Re: Frsky S6R Config Software
Posted: Wed Apr 29, 2020 10:33 am
by MikeB
Confusing since earlier you were using SA to change the stab. mode!
To start with, just use a single mix on channel 10 with a source of SE (or SA if that is what you are wishing to use). This will give outputs of +100%, 0% and -100%.
Mike
Re: Frsky S6R Config Software
Posted: Wed Apr 29, 2020 10:52 am
by manesty
Mike
I have set a single mix on channel 10 on SA using the channel monitor screen I can see the switch output change from -100 0 +100 but the receiver still wants to use the gyro no matter what position SA switch setting is.
Re: Frsky S6R Config Software
Posted: Wed Apr 29, 2020 1:43 pm
by MikeB
Does the Rx just stay in stabilisation mode or does it change to auto-level mode at all?
Mike
Re: Frsky S6R Config Software
Posted: Fri May 01, 2020 6:08 am
by martinwh99
Hello
I have the same problem.
Horus X12S,
OpenTx-x12s-2.3.7 (8b080683)
Companion 2.3.7 March 28 2020
For me it looks like none of the schwitches will take 100%
the following is only switching between -100 and 0. tried it with differnt switches, same result
CH10 SE Weight (100%) Switch (SA up) Off
+= SE Weight (0%) Switch (SE -) Stab
+= SE Weight (-100%) Switch (SE Down) Auto
This is working
CH10 SE Weight (-100%) Switch (SA up) Off
+= SE Weight (0%) Switch (SE -) Stab
+= SE Weight (-100%) Switch (SE Down) Auto
regards
Martin
Re: Frsky S6R Config Software
Posted: Fri May 01, 2020 7:25 am
by Kilrah
Don't populate the "Switch" setting, only the "Source".
Re: Frsky S6R Config Software
Posted: Sat May 02, 2020 5:29 am
by martinwh99
Kilrah wrote: ↑Fri May 01, 2020 7:25 am
Don't populate the "Switch" setting, only the "Source".
Thanks Kilrah thad did work. Now everything is working fine
regards
Martin
Re: Frsky S6R Config Software
Posted: Mon May 25, 2020 7:40 pm
by bazze
mak wrote: ↑Mon Apr 27, 2020 4:41 pm
MikeB wrote: ↑Mon Apr 27, 2020 3:56 pm
Go to the download section for the S6R and download "Tool-FrSky Freelink".
Remember to run the tool as an Administrator. Otherwise it will not run and, what worse, it will just quit with no message.
Have done all this, but still it's not opening!!! Using Windows 10....