ok,
I have a hard one for all the Gurus out there! I have been using Taranis for two years now and know a lot about it and how to program on it, but this one has me stumped!
I am flying a plane with flaps that also act as ailerons. It's the Legacy Aviation 84" Turbo Bushmaster. I have the normal flying mode where flaps are coupled to the ailerons for higher 3D rate flying. I flip my SB switch to mid position and the flaps stop acting like ailerons and go down to flap position. This is all well and good, but I also have a separate setting for Rate/Expo that is assigned to the SD switch that I want to happen when i am flying with flaps for the landing phase. Also during this landing phase, I have a different throttle setting, also on a different switch SA. So my question is, I would like to keep my high/Low rates on the SD switch, so that I can switch those anytime I want in ANY phase of flight and also keep my throttle setting on SA, so I can also switch that during any phase of flight, but when I flip the SB switch to activate flaps, I want that switch to take over from SA and SD and change both of those settings to be the settings I want during the landing phase. This way, i am only flipping one switch to go in and out of the landing or taking off phase of flight and not having to switch and remember three different switch settings in order to make these changes. SO, my question is, how would you set this up to make those changes occur how I am wanting? I have tried SO MANY different things to make this happen and can't seem to figure it out. PLEASE HELP ME figure this one out!
Thanks!
-Clint
!Taranis X9D Plus GURUS! Here's a challenge for ya...!
General Help and support for the Taranis Radio.
-
- Posts: 1
- Joined: Fri Sep 06, 2019 9:36 pm
- Country: -
Return to “General help (FrSky Taranis radio)”
Jump to
- OPENRC News & Information
- ↳ General Information & Rules
- ↳ Feedback
- General help and information
- ↳ Software
- ↳ Hardware
- ↳ General help (FrSky Taranis radio)
- Open Radio Control Transmitter Firmwares
- ↳ General model setup questions
- ↳ er9x / gruvin9x / th9 based firmwares
- ↳ Template Library
- ↳ Splash Screen Library
- ↳ Helicoptor Programming
- ↳ radioclone
- ↳ stock firmware (fly sky th9x)
- ↳ Template Library
- ↳ Sound Pack Library
- ↳ Edge TX
- ↳ openTx
- ↳ openTx for FrSky radios
- ↳ openTx model setup
- ↳ er9x
- ↳ er9x model setup
- ↳ ersky9xr
- ↳ erskyTx (was ersky9x)
- ↳ ersky9x model setup
- ↳ gruvin9x
- ↳ gruvin9x model setup
- ↳ th9x
- ↳ th9x model setup
- ↳ gv9x
- ↳ radioclone
- ↳ radioclone model setup
- ↳ tgy9xr
- ↳ tgy9xr model setup
- ↳ AR-T6
- ↳ other
- Desktop Software to Program Your Transmitter
- ↳ eePe
- ↳ companion9x
- ↳ eepSKYe
- Open Radio Control RF Systems & Hardware
- ↳ OpenLRS
- ↳ OpenLRSng
- ↳ OpenLRSng hardware
- Closed Source Radio Control RF Systems & Hardware
- ↳ Royal Way - Rlink UHF Long Range System
- Transmitter Hardware
- ↳ FlySky TH9X / Turnigy 9X / Eurgle 9X radio
- ↳ SMARTIEPARTS PROGRAMMER
- ↳ HARDWARE MODS & HACKS
- ↳ FRSky Telemetry Mods
- ↳ ArduPilot Mods
- ↳ Electronic Mods
- ↳ Hardware Mods
- ↳ Soldering, Hardware, Skills
- ↳ DSM2/DSMX Mods
- ↳ UPGRADE BOARDS
- ↳ sky9x upgrade board
- ↳ gruvin9x upgrade board
- ↳ 9Xtreme upgrade board
- ↳ RF MODULES
- ↳ The FRSKY Forum
- ↳ PROGRAMMERS
- ↳ FrSky Taranis radio
- ↳ FRSky Horus radio
- ↳ Turnigy 9XR PRO radio
- ↳ Orange DSM Telemetry module
- ↳ Turnigy 9XR radio
- ↳ PROGRAMMERS
- ↳ Other Radios
- ↳ Retro Radios
- Other OPEN Projects
- ↳ General RC Electronic Projects and Discussion
- ↳ OpenXVario - an open source vario supported by the open source firmwares!!
- ↳ Other Electronic Projects
- ↳ OpenFlightStab
- ↳ OpenLRSng
- ↳ 3D Printing
- Other Forums
- ↳ The Pickled Gnu (The Pub)
- ↳ FPV Projects
- ↳ Reviews
- ↳ Where to buy / Spares / Modules? Selling up?
- Links
- ↳ er9x on Google Code
- ↳ ersky9x on Github
- ↳ Gruvin9x on Google Code
- ↳ th9x on Google Code
- ↳ openTx on Google Code
- ↳ gv9x on Google Code
- ↳ radioclone on Sourceforge
- ↳ eePe on Google Code
- ↳ companion9x on Google Code
- ↳ 9X Guides
- ↳ openxvario