9xr pro total shot down

Cant get your radio to work? General Hardware issues?
Post Reply
nico
Posts: 16
Joined: Sun Jun 04, 2017 2:07 pm
Country: Philippines

9xr pro total shot down

Post by nico » Sat Nov 17, 2018 3:13 am

hi everybody! pls give me any idea on how to restore my 9xr pro function? after pressing the button near the usb port while powering up( following the instruction of "SAMBA restoring a brick transmitter") the screen totally shot off the only remaining function is the light, i have downloaded the SAMBA 2.18 on my laptop but i don't know what next step should i made, any help will be greatly appreciated, thank you guys in advance,


User avatar
KAL
Posts: 552
Joined: Thu Oct 10, 2013 4:36 pm
Country: Germany
Location: somewhere near Rothenburg ob der Tauber

Re: 9xr pro total shot down

Post by KAL » Sun Nov 18, 2018 4:23 pm

Hi,
I have no experience in doing this but I can point you to some info:
Go to this thread. At the end ot the first post you'll find a PDF which shows you how to restore the firmware.
And in this post you'll find a ZIP with all files you will need.

Klaus
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x  / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )

User avatar
MikeB
9x Developer
Posts: 16526
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9xr pro total shot down

Post by MikeB » Sun Nov 18, 2018 11:18 pm

The instructions in "9XR Pro Using SAM-BA to restore bricked Tx 2014-02-12.pdf" should get you working again. Make sure you run the option to set the NVM bit that enables "execute from flash". You would not be the first person to do everything else OK and then wonder why it still doesn't work!

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

nico
Posts: 16
Joined: Sun Jun 04, 2017 2:07 pm
Country: Philippines

Re: 9xr pro total shot down

Post by nico » Mon Nov 19, 2018 7:46 am

KAL wrote:
Sun Nov 18, 2018 4:23 pm
Hi,
I have no experience in doing this but I can point you to some info:
Go to this thread. At the end ot the first post you'll find a PDF which shows you how to restore the firmware.
And in this post you'll find a ZIP with all files you will need.

Klaus
[thanks kal for your responce ill work on this and get back to you for the result]

nico
Posts: 16
Joined: Sun Jun 04, 2017 2:07 pm
Country: Philippines

Re: 9xr pro total shot down

Post by nico » Mon Nov 19, 2018 7:47 am

MikeB wrote:
Sun Nov 18, 2018 11:18 pm
The instructions in "9XR Pro Using SAM-BA to restore bricked Tx 2014-02-12.pdf" should get you working again. Make sure you run the option to set the NVM bit that enables "execute from flash". You would not be the first person to do everything else OK and then wonder why it still doesn't work!

Mike
[thanks mike]


nico
Posts: 16
Joined: Sun Jun 04, 2017 2:07 pm
Country: Philippines

Re: 9xr pro total shot down

Post by nico » Mon Nov 19, 2018 9:33 am

hello mike, can i use the SAMBA v2.18?

User avatar
MikeB
9x Developer
Posts: 16526
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9xr pro total shot down

Post by MikeB » Mon Nov 19, 2018 10:57 am

I would think so, although I never tried SAMBA since v2.12.
For just flashing the firmware, you should be able to select a board type of at91sam3s8-ek, no need to change any of the SAMBA configuration files. Those changes are only needed to allow access to the EEPROM from SAMBA.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

nico
Posts: 16
Joined: Sun Jun 04, 2017 2:07 pm
Country: Philippines

Re: 9xr pro total shot down

Post by nico » Mon Nov 19, 2018 12:47 pm

thanks mike


Post Reply

Return to “Hardware”