openrcforums

normal i use 1 vario sensor is GY63,today i try addon frsky vario Vari-H,it ok work why ?

before use GY63 on frsky X8r it ok,yesterday think i have frsky vario Vari-H sensor ,try connect 2 sensor,is work and work fine .... 2 sensor ID is different ???

It is normal for both to work at the same time as long as the sensor physical ID is set to a different value.

OXS gy63 is use normal set,and frsky vario Vari-H sensori no set ID use normal

Then all is good as you can see...

Telemetered numerical values, better than using one

if i conect 2 gy 63 on 1 pro mini need set different 12C ID ?

bbq wrote: ↑Sat May 12, 2018 8:18 am if i conect 2 gy 63 on 1 pro mini need set different 12C ID ?

Yes, mstrens describes it in chapter 4.1 of "oXs_config_description.h"

gy 63 CSB pin to VDD ?

or CSB to PS ?

This worked for me:
http://openrcforums.com/forum/viewtopic ... SB#p134681

i check oXs_config_advanced.h gy63 ID is 0,an frsky vario Vari-H ID is 0,why can use together ? frsky sensors ID download/file.php?id=6955&sid=078618554 ... 778421683f

bbq wrote: ↑Sat May 12, 2018 12:18 pm i check oXs_config_advanced.h gy63 ID is 0,an frsky vario Vari-H ID is 0,why can use together ?

Hmmm, good question Can you post the sensor screen with both sensors and the ID's?

two sensors together use

only conect frsky vario Vari-H sersor no change to 0m ?

frsky vario Vari-H Buy it back. No change any.

how can see frsky vario Vari-H ID?

two sensors use,GY63 vario + frsky vario Vari-H
https://youtu.be/Q20AG9iy07A

bbq wrote: ↑Mon May 14, 2018 11:09 am how can see frsky vario Vari-H ID?

Go to the telemetry screen in your model menue. The numbers displayed are shifted by 1.
- what do you want to achieve using two GY63?
- what do you want to achieve using openXsensor and additionally FrSky Vario H?

https://www.youtube.com/watch?v=alZfqbgxtBc
today i try gy86 + frsky vario Vari-H

i use FROS

bbq wrote: ↑Tue May 15, 2018 5:49 ami use FROS

I do not use FrOS, sorry.

Can you explain, why you want to use 2 GY63? If i know, i can edit the oXs configuration files.

because i have FrSky Vario H,want add together use,i think two sensors Comparable will good than 1 sensor ?

It makes little sense to use 2. Just use one that works well.

I don't think FrOS supports multiple sensors of the same type anyway.

bbq wrote: ↑Tue May 15, 2018 8:19 am because i have FrSky Vario H,want add together use,i think two sensors Comparable will good than 1 sensor ?

openXsensor can use two GY63 and calculate the average values. The idea was, to reduce noise or decrease reaction time (keeping the same noise level). But tests showed, that one sensor is always fast enough and noise was never an issue with openXsensor and MS5611, even in high sensitivity (fast) configurations.

I do not know if my understanding is correct or not. Two sensors are required to compensate for the error, but one processor is required ?

bbq wrote: ↑Tue May 15, 2018 11:38 am I do not know if my understanding is correct or not. Two sensors are required to compensate for the error, but one processor is required ?

Correct. Two sensors are read from one processor. It calculates the average of the sensors and transmits it.

Carbo wrote: ↑Sat May 12, 2018 9:13 am Yes, mstrens describes it in chapter 4.1 of "oXs_config_description.h"

Again, there is no need to do so, but you can try of course for yourself.

Kilrah wrote: ↑Tue May 15, 2018 9:25 am It makes little sense to use 2. Just use one that works well.

I don't think FrOS supports multiple sensors of the same type anyway.

I think that you are correct. If use 2 sensors, they may make problems with each other due to errors.