DIY TOUCH-MI , wire-less autolevelling Z-probe(3D Printing)

Any 3D printing projects
Post Reply
User avatar
midelic
Posts: 99
Joined: Mon Dec 23, 2013 9:57 pm
Country: -

DIY TOUCH-MI , wire-less autolevelling Z-probe(3D Printing)

Post by midelic » Wed Nov 13, 2019 1:39 pm

It is an electronic projects too, so it fits right here.
Very simple project that can be adapted to any 3d printer.

https://www.thingiverse.com/thing:3659699
Last edited by midelic on Fri Nov 15, 2019 4:58 pm, edited 1 time in total.


User avatar
bob195558
Posts: 2139
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: DIY TOUCH-MI, wire-less autoleveling Z-probe (3D Printing)

Post by bob195558 » Wed Nov 13, 2019 4:14 pm

Hi midelic,
We do not have a category for 3D Printing yet,
but hopefully we will some time soon !

I like to suggest that you mark at the end of the Tile Topic in parentheses,
something like (3D Printing), so that if/when there is a category for RC-3D-Printing
it will be helpful if/when a category for 3D Printing be made
and also would be a help when Searching for a Topics like this.

This project you have, looks very well done, good job. :)
DIY Tough MI wireless auto leveling Z probe_.jpg


Do you use a Raspberry Pi with EZPi image (Octoprint) ?
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
MikeB
9x Developer
Posts: 16635
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: DIY TOUCH-MI , wire-less autolevelling Z-probe

Post by MikeB » Wed Nov 13, 2019 5:10 pm

Other Open Projects!!! There is now a "3D Printing" sub-Forum (with nothing in it!). I've just created it.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
bob195558
Posts: 2139
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: DIY TOUCH-MI , wire-less autolevelling Z-probe

Post by bob195558 » Wed Nov 13, 2019 7:50 pm

Hi Mike,
Thank you Mike for doing this !

The path to find where:
openrcforums.com / Board index / Other OPEN Projects / 3D Printing
https://openrcforums.com/forum/viewforum.php?f=129

Can the 3D Printing post here at "Other Electronic Projects",
the ones with (CR10 3D Printer) at the end of the Tile Topic,
be moved to this new category "3D Printing",
or would this mess-up the links to them ? :?:
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
midelic
Posts: 99
Joined: Mon Dec 23, 2013 9:57 pm
Country: -

Re: DIY TOUCH-MI, wire-less autoleveling Z-probe (3D Printing)

Post by midelic » Fri Nov 15, 2019 5:07 pm

bob195558 wrote:
Wed Nov 13, 2019 4:14 pm
Hi midelic,
We do not have a category for 3D Printing yet,
but hopefully we will some time soon !

I like to suggest that you mark at the end of the Tile Topic in parentheses,
something like (3D Printing)
Do you use a Raspberry Pi with EZPi image (Octoprint) ?
Done that(3D Printing).

I don't have Raspberry Pi with EZPi image (Octoprint).
But as I'm a DIY guy I have ESP3D flashed on an ESP8266 attached to my 3Dprinter
https://github.com/luc-github/ESP3D

I plan to improve that DIY touch-Mi project adding on the back of it an ESP8266 and communicate with the existing ESP8266 connected to a z-probe connector.This way I can make it really wifi wireless.
I have made already the board and populate it I have still to pull myself out to do it.


Post Reply

Return to “3D Printing”