ERSKYTx (was ersky9x) Questions

erskyTx runs on many radios and upgrade boards
ersky9x was a port of er9x for use on the sky9x board.
AlessB
Posts: 27
Joined: Wed Mar 01, 2017 9:09 am
Country: Ukraine

Re: ERSKYTx (was ersky9x) Questions

Post by AlessB » Mon Dec 28, 2020 6:25 pm

Hi Mike. I tried your recommendation. But multiply max 60 unit and divisor 232. Everything is correct in the menu 1852 and 1000, but CS1 shows multiplier 60 and divisor 232, and calculation output this


User avatar
MikeB
9x Developer
Posts: 17381
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: ERSKYTx (was ersky9x) Questions

Post by MikeB » Mon Dec 28, 2020 8:44 pm

Did you set the values in eepskye? It looks like I haven't handled larger values being edited in eepskye. Please try setting the values on the radio.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

AlessB
Posts: 27
Joined: Wed Mar 01, 2017 9:09 am
Country: Ukraine

Re: ERSKYTx (was ersky9x) Questions

Post by AlessB » Tue Dec 29, 2020 6:08 am

Hi Mike. Thanks for your answer. I tried in eepsky and radio (Ar9x). Both results are the same. Firmware last test. I can take screenshots if needed.

User avatar
MikeB
9x Developer
Posts: 17381
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: ERSKYTx (was ersky9x) Questions

Post by MikeB » Tue Dec 29, 2020 7:33 pm

According to my testing, the values displayed on the radio while editing a single Scaler are correct, and are used correctly in the calculation.
The values displayed on the screen showing 7 Scalers are showing incorrectly, but the real values are still used in the calculation.
eepskye is wrong and will not edit the values correctly. However, if you don't edit a value, eepskye should keep the value set on the radio.
I have fixes for eepskye and the radio screen displaying 7 Scalers. I'll post these in the next day or 2.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

AlessB
Posts: 27
Joined: Wed Mar 01, 2017 9:09 am
Country: Ukraine

Re: ERSKYTx (was ersky9x) Questions

Post by AlessB » Thu Dec 31, 2020 7:04 pm

Mike thank for you very job! Happy New Year!


User avatar
MikeB
9x Developer
Posts: 17381
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: ERSKYTx (was ersky9x) Questions

Post by MikeB » Sun Jan 03, 2021 12:24 pm

I've posted an update with this fix in. eepskye is included (.exe only), this is the version that is compiled using QT5.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

AlessB
Posts: 27
Joined: Wed Mar 01, 2017 9:09 am
Country: Ukraine

Re: ERSKYTx (was ersky9x) Questions

Post by AlessB » Sat Jan 09, 2021 11:46 am

Mike thanks. Now everything is showing correctly.

olivierhacking
Posts: 14
Joined: Sun Jan 10, 2016 8:44 am
Country: -

Re: ERSKYTx (was ersky9x) Questions

Post by olivierhacking » Mon Feb 22, 2021 6:42 pm

I am running the Turnigy 9X with the 9xtreme board (ersky9x).

If I understand correctly, the TBS Crossfire module needs to use the CRSF protocol, however I do not see this as an option on my radio.

Is there a way for me to get this running? I don't want my tx signal to cut out just as I'm behind a building (like now using FrSky XJT)...

User avatar
MikeB
9x Developer
Posts: 17381
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: ERSKYTx (was ersky9x) Questions

Post by MikeB » Mon Feb 22, 2021 7:59 pm

What revision of erskyTx are you using?
XFIRE (CRSF) protocol should be present for the external module (last option after MULTI).

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

olivierhacking
Posts: 14
Joined: Sun Jan 10, 2016 8:44 am
Country: -

Re: ERSKYTx (was ersky9x) Questions

Post by olivierhacking » Tue Feb 23, 2021 3:15 pm

I have version V. 3531-Mike

08.01.2016... I assume this is why I don't see XFIRE?

I could update it to the latest ERSKYTx, but am afraid of losing all my settings! Unfortunately I am no seasoned user :mrgreen:

EdwardMcRichy
Posts: 45
Joined: Sat Dec 09, 2017 4:31 am
Country: -
Location: Sahuarita Arizona

Re: ERSKYTx (was ersky9x) Questions

Post by EdwardMcRichy » Tue Feb 23, 2021 7:07 pm

olivierhacking wrote:
Tue Feb 23, 2021 3:15 pm
I have version V. 3531-Mike

08.01.2016... I assume this is why I don't see XFIRE?

I could update it to the latest ERSKYTx, but am afraid of losing all my settings! Unfortunately I am no seasoned user :mrgreen:
I've never lost a model or any other setting when flashing my radio to a newer version of firmware.
When I'm not flying I'm dreaming of flying, when I'm not dreaming of flying.....I'm asleep

User avatar
MikeB
9x Developer
Posts: 17381
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: ERSKYTx (was ersky9x) Questions

Post by MikeB » Tue Feb 23, 2021 7:33 pm

olivierhacking: Do you have eepskye installed? If so, just backup both your EEPROM (models) and Flash (firmware) to your PC, then flash the new firmware. I have always tried to keep new firmware to be fully compatible with models stored from previous versions.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

olivierhacking
Posts: 14
Joined: Sun Jan 10, 2016 8:44 am
Country: -

Re: ERSKYTx (was ersky9x) Questions

Post by olivierhacking » Wed Feb 24, 2021 4:06 pm

I have never flashed any new firmware since installing the board. Is using eepskye the way to go? I will backup EEPROM and Flash before attempting to install the new firmware.

User avatar
MikeB
9x Developer
Posts: 17381
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: ERSKYTx (was ersky9x) Questions

Post by MikeB » Thu Feb 25, 2021 7:31 pm

You have two methods, one is to install eepskye, and flash the radio from that. eepskye also provides an easy way to read both the flash memory and the EEPROM.
The other is to start the radio in bootloader mode (power on with the two horizontal trims held towards the centre). Then connect the radio to your computer using USB. You should find two "hard drives" appear, one is the flash memory and the EEPROM and the other is the SD card. Copy the two files (firmware and EEPROM) from the smaller drive, these are your backups.
Next copy the firmware update file to the "FIRMWARE" directory on the SD card, then disconnect the USB.
The bootloader has an option to update the firmware, select that, then select the file you copied to the SD card and confirm. You will need a LONG press of the MENU button to action these options.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

rwsams
Posts: 6
Joined: Tue Oct 29, 2013 7:45 pm
Country: -

Re: ERSKYTx (was ersky9x) Questions

Post by rwsams » Sat Feb 27, 2021 9:19 pm

Hi, I hope this is the right place for this question. I have a TH9X radio with the 9Xtreme board. In order to keep up with the Multi-Protocol module firmware, I downloaded test version erskyTxR223B1 and extracted the zip file. I was able to install the ersky9x9XT_rom.bin using eePe v422 and the radio/module works fine. However, if I try to launch the eePe version that comes in the zip file, it complains about a bunch of missing dll's and won't launch. Am I doing something wrong?
Thanks in advance,
Bob Sams
Corvallis, OR

User avatar
MikeB
9x Developer
Posts: 17381
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: ERSKYTx (was ersky9x) Questions

Post by MikeB » Sat Feb 27, 2021 9:54 pm

Nothing wrong. I have needed to migrate eepskye to being built using QT5 instead of QT4. This needs the QT5 dll files.
On the test versions thread there is eepskye5.zip dated 12-Dec-2020 19:53. You need to download and install this, then overwrite the eepskye.exe file with the latest one.
Install by extracting all files, keeping the directory structure, to a suitable directory (e.g. eepskye5).

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

rwsams
Posts: 6
Joined: Tue Oct 29, 2013 7:45 pm
Country: -

Re: ERSKYTx (was ersky9x) Questions

Post by rwsams » Sun Feb 28, 2021 2:01 am

Thanks so much. That makes perfect sense.
Bob

rwsams
Posts: 6
Joined: Tue Oct 29, 2013 7:45 pm
Country: -

Re: ERSKYTx (was ersky9x) Questions

Post by rwsams » Sun Feb 28, 2021 6:11 am

Mike,
Worked like a charm. Thanks again.
Bob


Post Reply

Return to “erskyTx (was ersky9x)”