Er9x128

er9x is the best known firmware. It has a superb range of features and is well supported by the community. Well worth trying out.
User avatar
Kilrah
Posts: 10277
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Er9x128

Post by Kilrah » Sat Apr 06, 2013 7:46 am

Yes!

Image


Romushock
Posts: 47
Joined: Thu Nov 08, 2012 8:35 am
Country: -
Location: North Italy

Re: Er9x128

Post by Romushock » Sat Apr 06, 2013 4:22 pm

Thanks Kilrah, would You be so kind to place other foto where can to see where You hook up external power?
I desolder out all wires, but it still don't work...

User avatar
Kilrah
Posts: 10277
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Er9x128

Post by Kilrah » Sat Apr 06, 2013 4:29 pm

It's actually powered by the programmer on that photo.

Romushock
Posts: 47
Joined: Thu Nov 08, 2012 8:35 am
Country: -
Location: North Italy

Re: Er9x128

Post by Romushock » Sun Apr 07, 2013 9:58 am

Well, till now nothing to be good... I've desolder out all wires, clean all with alcohol, try to power board from USBASP, try to hook up other one display - nothing to do, it still be blank. So, before desolder out M128 I have two questions:
- can somebody, who had a success with a M128 transplantation, post here own fuses?
- does it possible, that I've fry in some mode LCD outputs (chip still be seen by PC)?
thks

User avatar
jhsa
Posts: 19033
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Er9x128

Post by jhsa » Sun Apr 07, 2013 10:09 am

Can you make a servo move by connecting it to a rerceiver bound to the tx?
does the radio beep if you mess with it?
If yes, then there could maybe be a problem with the LCD.
If not, than I think that the problem is somewhere else..

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW


JustinTime
Posts: 140
Joined: Tue Jan 29, 2013 4:12 am
Country: -
Location: SoCal

Re: Er9x128

Post by JustinTime » Sun Apr 07, 2013 3:54 pm


Romushock
Posts: 47
Joined: Thu Nov 08, 2012 8:35 am
Country: -
Location: North Italy

Re: Er9x128

Post by Romushock » Sun Apr 07, 2013 5:55 pm

So, after spend one week of my f...d life, I find the answer... FUSES, guys, f...d fuses... I read fuses of my other Tx9 with M64 and copy it to M128. And a miracle happened!!! I was at one step to consider me an idiot... Thanks to all participants, the curtain falls...
P.S. For save the time and brain health of followers here are screenshots of AVRStudio.

Image Image

Romushock
Posts: 47
Joined: Thu Nov 08, 2012 8:35 am
Country: -
Location: North Italy

Re: Er9x128

Post by Romushock » Tue Apr 09, 2013 9:48 am

OOOOOH, I've singed a victory too soon... Hooking up a voice board, I shortened motherboard. Was a nice spark and tantallum cap was explose me in face. Cap and M128 was replaced to new ones, but on display now can see something, like this:
[BBvideo 425,350]http://www.youtube.com/watch?v=MFLRQep6 ... e=youtu.be[/BBvideo]
Have somebody a weak idea, what's happened?

User avatar
jhsa
Posts: 19033
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Er9x128

Post by jhsa » Tue Apr 09, 2013 10:21 am

Hmmm, check the fuses?? Also after the short is the regulator still ok? and supplying 5V?
Answering my question, it might be or the atmega wouldn't work? but better measure ;)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

ReSt
Posts: 1523
Joined: Tue Dec 27, 2011 11:34 pm
Country: -

Re: Er9x128

Post by ReSt » Tue Apr 09, 2013 10:24 am

and check all voltage regulators
5Volt and 3.3 Volt on main board
5 Volt on the board with the beeper
5 Volt in the module

Reinhard

Romushock
Posts: 47
Joined: Thu Nov 08, 2012 8:35 am
Country: -
Location: North Italy

Re: Er9x128

Post by Romushock » Tue Apr 09, 2013 10:40 am

2 Joào: M128 is new, programmed externally, all is OK, veryfied already being soldered to MB.
2 Reinhard: can You post here a foto with an explanation, please?
thks, guys

User avatar
jhsa
Posts: 19033
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Er9x128

Post by jhsa » Tue Apr 09, 2013 11:03 am

It doesn't hurt to check again.. It could be that is not working at 16Mhz anymore for some reason.. That would slow the screen down?
also where did you short the board?
A picture from the affected part could probably help? :)
I've learnt that the famous phrases "I've already checked it" or "it was working before" don't apply most of the times :) :D
We have to check and recheck, and recheck...

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

ReSt
Posts: 1523
Joined: Tue Dec 27, 2011 11:34 pm
Country: -

Re: Er9x128

Post by ReSt » Tue Apr 09, 2013 5:43 pm

Have a look at this post
http://www.rcgroups.com/forums/showpost ... count=6754

It should show you most of what you are looking for.

Reinhard

User avatar
MikeB
9x Developer
Posts: 16609
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Er9x128

Post by MikeB » Sun Apr 14, 2013 12:28 pm

Possibly lost somewhere in othjer things in this thread, but I did update the first post with a test version of er9x-128 that includes flight phases and stick scrolling. No downloads yet. I was hoping someone would test the flight phases before I put it in a general release, I don't have a functional 9x with a 128 main board to do full testing.
I've just added a provisional r789, any testers out there?

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
jhsa
Posts: 19033
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Er9x128

Post by jhsa » Sun Apr 14, 2013 12:54 pm

Downloaded.. ;)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
MikeB
9x Developer
Posts: 16609
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Er9x128

Post by MikeB » Thu Apr 18, 2013 4:09 pm

New version or er9x-128 on the first post.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!


Post Reply

Return to “er9x”