Where to find er9x

er9x is the best known firmware. It has a superb range of features and is well supported by the community. Well worth trying out.
Sudsy
Posts: 9
Joined: Mon Sep 30, 2013 3:09 am
Country: -

Re: Where to find er9x

Post by Sudsy » Wed Jan 28, 2015 3:31 pm

Thanks for that setup guide. This is like trying to drive through Memphis with a Boston road map! It sure was easy with the right directions.

I think these developers should wait to release until they have all the documentation in order.

Sudsy

Daedalus66
Posts: 1774
Joined: Tue Dec 27, 2011 8:22 pm
Country: -
Location: Ottawa

Re: Where to find er9x

Post by Daedalus66 » Wed Jan 28, 2015 4:26 pm

I sympathize, but I'd rather not postpone my trip for a couple of years while someone produces a Memphis map. I'd go on the Memphis website and find one! Or ask a local. Which is essentially what the forum allows.

This is the world of open source -- it's all voluntary. In fact, the documentation here is sometimes a lot better than you can find for some commercial products. The lack of coordination does put a burden on those looking for information, but the benefit is the amazing power of the free and highly innovative firmware.

By the way, the developer is singular. His name is Mike. I hope you've contributed.

Some of us are supporting him by helping with the documentation issue. As my colleague said, we hope to have the new version of the manual out next week.

Sudsy
Posts: 9
Joined: Mon Sep 30, 2013 3:09 am
Country: -

Re: Where to find er9x

Post by Sudsy » Fri Jan 30, 2015 4:31 am

How will I know when the manual is available?

User avatar
jhsa
Posts: 18011
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Where to find er9x

Post by jhsa » Fri Jan 30, 2015 8:31 am

Don't worry, we will make sure everybody know about it. Keep following this forum :)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Sudsy
Posts: 9
Joined: Mon Sep 30, 2013 3:09 am
Country: -

Re: Where to find er9x manual

Post by Sudsy » Thu Feb 05, 2015 7:45 pm

Has the manual been released yet? Now I am trying to change the channel assignments to match a DSM2 transmitter. TAER= 1234. I can't find the page that used to let me do that. Right now my throttle is mapped to chan 3. I am trying to setup a DSM2 receiver that has gyro stab built in. I need the channel order to be that way because right now it seems like gyro is causing the throttle to run up when I move the aircraft to check pitch gyro. I have the servos running right without gyro but I had to reassign the channels of the rcvr to match the transmitter and have throttle on chan 3 now. Also how do I reverse channels on this thing now?

Getting very frustrated with it.

Sudsy


User avatar
jhsa
Posts: 18011
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Where to find er9x

Post by jhsa » Thu Feb 05, 2015 8:14 pm

go to the Model setup menu, Mixer, select channel 1, highlight it, press menu, select edit.
An edit mix menu will open.. Change the source value to Thr.

Do the same to the other channels and select the right source.
If you want the same channel order the next time you create a model, go to the radio setup index menu, Controls, Channel order, press menu and select TAER. The next time you create a model or apply a template, it will respect that order..

To reverse a channel go to the limits menu in model setup, highlight the channel you want to reverse, move the cursor to the right, and change "---" to "INV"

The manual is nearly ready and it won't take long now.. Don't forget we do this on our free time. We are working on some examples at the moment..

Ahh, that thing is called er9x I suppose? and it is just one of the best "Things" that could have happened to the RC World.. The good thing is, we don't have to use that "thing" if we don't like it ;) :)
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Sudsy
Posts: 9
Joined: Mon Sep 30, 2013 3:09 am
Country: -

Re: Where to find er9x

Post by Sudsy » Thu Feb 05, 2015 9:17 pm

Well that does not seem to work. On the screen that comes up after the Splash screen I select to see the Model name and the graphic display of the channels that also shows the trim positions. . No matter what I do in the setup channel assignments are not changing. I am just going to put it away and wait for the manual. I have not had any problems with my other 9x running that same version but using a FrSky module and a new X8R receiver. I just successfully set up a plane with that and a Vector but sbus made that easy. This DSM2 Orange module is something different. The receiver I am attempting to use is a Orange RX3SM Micro Flight Stabilizer. The receiver board is directly connected to the gyros and with out the 9x transmitting on the proper channels makes the gyro control the wrong channels if I connect it to operate with the gyros off or the gain all the way down.

Sudsy

User avatar
KAL
Posts: 551
Joined: Thu Oct 10, 2013 4:36 pm
Country: Germany
Location: somewhere near Rothenburg ob der Tauber

Re: Where to find er9x

Post by KAL » Thu Feb 05, 2015 9:36 pm

The channel assignment of an existing model will not change until you change it by yourself in the mixer menu.
You have to move the lines with the appropriate inputs to the channel line you need.

For TAER e.g the line with THR as source you have to move to channel one (first line in mixer menu) ...
the line with RUD as source you have to move to channel 4 ...

Klaus
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x  / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )

User avatar
jhsa
Posts: 18011
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Where to find er9x

Post by jhsa » Thu Feb 05, 2015 10:06 pm

A couple pictures of your setup might help.. as well as posting the eeprom here.. then we can see what you're trying to do.. I never seen that controller board, so I don't know what it needs from the radio..

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

javitu
Posts: 23
Joined: Tue Sep 29, 2015 1:47 pm
Country: -

Re: Where to find er9x

Post by javitu » Tue Dec 15, 2015 4:32 pm

Hello guys,

I just flashes one radio with atmega64 from the last firmware here,

https://code.google.com/p/er9x/ (its up too date)

And i flashed 2 radios 2 weeks ago (they had atmega128) from:

http://www.er9x.com/



Atmega128 firmware is up to date?

User avatar
MikeB
9x Developer
Posts: 15712
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Where to find er9x

Post by MikeB » Tue Dec 15, 2015 4:52 pm

The firmware on www.er9x.com is the latest for both processors.
Googlecode is closing down, so I haven't put anything on there for a long time.

Mike.
ersky9x/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

javitu
Posts: 23
Joined: Tue Sep 29, 2015 1:47 pm
Country: -

Re: Where to find er9x

Post by javitu » Tue Dec 15, 2015 5:03 pm

MikeB wrote:The firmware on http://www.er9x.com is the latest for both processors.
Googlecode is closing down, so I haven't put anything on there for a long time.

Mike.
love you! ty

User avatar
jhsa
Posts: 18011
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Where to find er9x

Post by jhsa » Tue Dec 15, 2015 5:08 pm

;) :)
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

kaisar15R
Posts: 1
Joined: Mon Mar 28, 2016 7:34 pm
Country: -

Re: Where to find er9x

Post by kaisar15R » Mon Mar 28, 2016 7:36 pm

This site can’t be reached

The webpage at http://www.er9x.com/ might be temporarily down or it may have moved permanently to a new web address.


:oops: :cry: :shock: :?

Daedalus66
Posts: 1774
Joined: Tue Dec 27, 2011 8:22 pm
Country: -
Location: Ottawa

Where to find er9x

Post by Daedalus66 » Tue Mar 29, 2016 2:28 am

Er9x.com is back up.

AlexLmm
Posts: 34
Joined: Mon Oct 03, 2016 11:28 pm
Country: -

Re: Where to find er9x

Post by AlexLmm » Mon Sep 04, 2017 9:29 pm


User avatar
MikeB
9x Developer
Posts: 15712
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Where to find er9x

Post by MikeB » Mon Sep 04, 2017 10:07 pm

I've done a quick edit to point athttp://www.er9x.com/.

Mike.
ersky9x/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

Post Reply

Return to “er9x”