[SOLVED] Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

er9x is the best known firmware. It has a superb range of features and is well supported by the community. Well worth trying out.
Post Reply
whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

[SOLVED] Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Tue Sep 17, 2019 4:26 pm

Im trying. er9x frsky 822, m64. Use sbus via invertor (transistor), rc working. Recieve to M0 pin data, view from oscil. 9x modifled (switches to 41/42 pins).
Connect m0 lrs to mosi, no telemetry on display..
Trying invertor, no success.
Helьp :)
Last edited by whoim on Mon Oct 07, 2019 11:04 pm, edited 1 time in total.


User avatar
Kilrah
Posts: 10239
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by Kilrah » Wed Sep 18, 2019 6:56 am

Doesn't this LRS provide MAVLINK telemetry, not frsky?

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Wed Sep 18, 2019 3:37 pm

Kilrah wrote:
Wed Sep 18, 2019 6:56 am
Doesn't this LRS provide MAVLINK telemetry, not frsky?
Mavlink & s.port one time. Say, telemetry recieve working, if protocol: sbus?
Im send channels to qlrs via sbus, and need to recieve s.port back from qlrs.

Frsky = s.port, right?

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Thu Sep 19, 2019 2:24 pm

>Say, telemetry recieve working, if protocol: sbus?
In er9x-frsky t9x

User avatar
MikeB
9x Developer
Posts: 16585
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by MikeB » Thu Sep 19, 2019 2:59 pm

What Tx module and what receiver are you using?

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!


whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Sun Sep 22, 2019 11:53 am

MikeB wrote:
Thu Sep 19, 2019 2:59 pm
What Tx module and what receiver are you using?

Mike
Hello! Rx side: e32-433t20 100mv, 1.92 qczek firmware.
Tx side: e32-433t30 1w v6.2, 1 92 qczek.
FC: omnibus f4 pro v3, telemetry mavlink at softserial (moto pins).
Telemetry settings: mavlink 57600 on FC, 1.Mavlink enc 57600 on RX, 3. Mavlink + S.Port master on TX.
Mavlink present at tx side, s.port visible via oscil and led blink.

TX side in JR on T9X, s.port tx pin qlrs (m0) connected directly to pin2 atmega64 on T9X (rx0 pin).

User avatar
MikeB
9x Developer
Posts: 16585
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by MikeB » Sat Sep 28, 2019 9:32 pm

er9x on a M64 doesn't support mavlink protocol, unless the ARDUPILOT version does that. I'm not sure exactly what that supports. It also looks to use a baudrate of 38400.
The M64 doesn't have enough flash memory to include mavlink.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Wed Oct 02, 2019 7:48 pm

MikeB wrote:
Sat Sep 28, 2019 9:32 pm
er9x on a M64 doesn't support mavlink protocol, unless the ARDUPILOT version does that. I'm not sure exactly what that supports. It also looks to use a baudrate of 38400.
The M64 doesn't have enough flash memory to include mavlink.

Mike
No! TX module have mavlink & s.port both. Im use s.port pin for connect to m64 rx. Data present on this wire, i see via ossicilograf.

See: http://qczek.beyondrc.com/qczek-lrs-433 ... telemetry/

Maybe, invalid baudrate?

User avatar
MikeB
9x Developer
Posts: 16585
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by MikeB » Wed Oct 02, 2019 8:48 pm

SPort telemetry data is INVERTED serial, you need to put an inverter in the signal between the module and the M64.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Thu Oct 03, 2019 8:27 am

Yes, im trying inverter on bcr533 digital transistor, and see inverted signal via osicil. But at this time drone not have GPS FIX, and im reading: qczek not send telemetry data if no gps fix.

Im trying now today, ok, and record video.

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Thu Oct 03, 2019 9:36 am

MikeB wrote:
Wed Oct 02, 2019 8:48 pm
SPort telemetry data is INVERTED serial, you need to put an inverter in the signal between the module and the M64.

Mike
Hello! Im connect m64 via inverter, wait for gps fix (8 satellites), see video: https://youtu.be/gdTP1-fBphg
Screenshot_20191003-122941.png
Its mavlink telemetry via bluetooth, have 8 sats

User avatar
MikeB
9x Developer
Posts: 16585
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by MikeB » Thu Oct 03, 2019 9:45 am

The telemetry type and baud rate used depends on the protocol used for controlling the module. Are you using PXX (XJT)?

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Thu Oct 03, 2019 1:57 pm

MikeB wrote:
Thu Oct 03, 2019 9:45 am
The telemetry type and baud rate used depends on the protocol used for controlling the module. Are you using PXX (XJT)?

Mike
No, sbus. My tx lora have problem at AUX pin, xjt and ppm not work.. sbus work via inverter and RX pin.
Telemetry not work if protocol not xjt?

User avatar
MikeB
9x Developer
Posts: 16585
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by MikeB » Thu Oct 03, 2019 3:23 pm

SPort telemetry at 57600 baud is only enabled if the protocol is XJT or MULTI wit sub_protocol FrSkyX.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Thu Oct 03, 2019 8:22 pm

MikeB wrote:
Thu Oct 03, 2019 3:23 pm
SPort telemetry at 57600 baud is only enabled if the protocol is XJT or MULTI wit sub_protocol FrSkyX.

Mike
Tnx.. maybe, in future, can create inclusion and configuration without being bound to a protocol? In new versions?

whoim
Posts: 10
Joined: Tue Sep 17, 2019 4:20 pm
Country: -

Re: Anybody recieve telemetry to turniga9x er9xfrsky from qczek lrs?

Post by whoim » Fri Oct 04, 2019 8:10 am

Im stupid. Use invalid firmware for qczek tx module, sbus, non xjt. Now im update firmware, aux pin work!

Now all work! Telemetry present!
Details:
Connect t9x er9x 1pin JR to AUX pin qczek.
Select XJT D16 protocol on t9x model menu.
Connect M0 pin qczek (parallel led) to pin2 m64 (use 5pin JR box) via inverter (as for sbus, npn transistor).
Config qczek tx as XJT for input, 16 channels, Mavlink + S.Port Master in Telemetry.

On drone enable Mavlink 57600 at uart, enable Mavlink telemetry on qczek RX and not use silent mode.

Thanks!


Post Reply

Return to “er9x”