SPort device updating
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
2.0.18 has just been released. I've posted binaries and the changed source files on the first post.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
Thanks Mike.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
2.0.19 has been released so I've added 'maintenance mode' to it and posted binaries and changed sources on the first post.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
hello mike , I tried to flash the XJT module from 9XR pro with ER9X 218 and I can't do it :
Booting in maintenance mod , select update sport.
Powering off
select my firmware and confirm
waiting bar a finding Device
Powering On
Nothing happen , not event a bip for the module .
Even tried by disconnecting module and put back.
what do I do wrong ?
Tring to update XJT then XSR an LBT firmware ( XSR won't bind for now , don't know which firmware it is)
Thanks
Booting in maintenance mod , select update sport.
Powering off
select my firmware and confirm
waiting bar a finding Device
Powering On
Nothing happen , not event a bip for the module .
Even tried by disconnecting module and put back.
what do I do wrong ?
Tring to update XJT then XSR an LBT firmware ( XSR won't bind for now , don't know which firmware it is)
Thanks
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
When and where did you get the XJT module. I believe recent European units are 'locked' and cannot be updated.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
I bought it on Ebay , not new from a seller not in the professionnal business ... so I don't know.
I tried to upload XSR , but same . Block at finding device
I tried to upload XSR , but same . Block at finding device
Re: SPort device updating
Do you think it would change something if I flash my 9XR with open TX instead of Ersky9x r218 ?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
How are you connecting the XJT to the radio and powering it?
Unlikely that openTx will perform any differently.
Mike.
Unlikely that openTx will perform any differently.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
Yes I am powering it . I followed every steps of this : http://thrustworx.com/frsky-xjt-firmwar ... y-9xr-pro/
The LED on the XJT is Red Fix. But the 9XR says "finding device" without moving.
Apparently , my XJT is an EU from end 2015 , beginning 2016 . It may be locked , but i'm am Trying to update the last LBT firm ( tried with old versions too)
The LED on the XJT is Red Fix. But the 9XR says "finding device" without moving.
Apparently , my XJT is an EU from end 2015 , beginning 2016 . It may be locked , but i'm am Trying to update the last LBT firm ( tried with old versions too)
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
When you switch off the radio part way through this operation, does the LED on the XJT go off?
Also, if you use the XJT normally, with the protocol set to PXX, do you see a value for SWR? You may need to wrap your hand round the antenna to cause the SWR to read a non-zero value.
Mike.
Also, if you use the XJT normally, with the protocol set to PXX, do you see a value for SWR? You may need to wrap your hand round the antenna to cause the SWR to read a non-zero value.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
Yes the led goes off when a switch 9XR off , then goes red fix when powering back ON.
This is my setting : https://goo.gl/photos/6ChXYMC434kv4F8b6
IDK if I use it normally ^^ . SWR ? how do you check it ?
I tried it with hand wrapped , but nothing move, still searching for device.
I also tried to flash my XSR with http://thrustworx.com/frsky-x-series-re ... ete-guide/
Not powering it with FTDI USB but with my 5v rail .
But 9XR does the same thing , just nothing move frome finding device ??!!
EDIT : we are OK that signal ( Sport) wire on 9XR is N°5 :
Antenna
°
°
°
°
°<- pin Smartport
Botom
This is my setting : https://goo.gl/photos/6ChXYMC434kv4F8b6
IDK if I use it normally ^^ . SWR ? how do you check it ?
I tried it with hand wrapped , but nothing move, still searching for device.
I also tried to flash my XSR with http://thrustworx.com/frsky-x-series-re ... ete-guide/
Not powering it with FTDI USB but with my 5v rail .
But 9XR does the same thing , just nothing move frome finding device ??!!
EDIT : we are OK that signal ( Sport) wire on 9XR is N°5 :
Antenna
°
°
°
°
°<- pin Smartport
Botom
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
To test the SWR, just power the radio on normally, with the XJT plugged in. Then press DOWN LONG to get to the telemetry screens. Use LEFT and/or RIGHT to select a screen where the SWR value is displayed.
Is it always zero, even if you wrap your hand around the antenna.
The SPort wire is where you describe it.
It may be worth flashing the radio with the latest test version of ersky9x from here: viewtopic.php?f=7&t=4676#p65894. THis may help test things out as there is some debug code in it.
Mike.
Is it always zero, even if you wrap your hand around the antenna.
The SPort wire is where you describe it.
It may be worth flashing the radio with the latest test version of ersky9x from here: viewtopic.php?f=7&t=4676#p65894. THis may help test things out as there is some debug code in it.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
Yes SWR it's always 0 . When I wrap it with a metal tube , it beeps , but swr is still 0
When I create a new profil/SETUP SWR seems to work propely ( values change) but after a restart , SWR=0 ??
Ok I will try R219t
thanks mike for your help
EDIT : XJT has been made on 2015-09-19 ( written on it... )
EDIT2 : i'm on BL V2.1 and I updated ERsky to r219 of 13th august . But nothing change. And still the only way to see a value on SWR is when I create or change of model.
When I create a new profil/SETUP SWR seems to work propely ( values change) but after a restart , SWR=0 ??
Ok I will try R219t
thanks mike for your help
EDIT : XJT has been made on 2015-09-19 ( written on it... )
EDIT2 : i'm on BL V2.1 and I updated ERsky to r219 of 13th august . But nothing change. And still the only way to see a value on SWR is when I create or change of model.
Last edited by boutbou on Fri Aug 19, 2016 12:24 pm, edited 2 times in total.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
OK, power on normally, then use UP LONG, then RIGHT a few times to get to the DEBUG menu. The bottom line shows "TelRxCount" with two numbers after it. The first number is a count of the number of telemetry bytes received. This should be counting all the time with the XJT plugged in.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
No it was not on my 1rst config ( bind with a X4RSB) , TelRXcount 0000 0101
BUT : when i'm changing model , it count . even after a reboot , SWR =0 but telrx counting. I have no receptor bind with this model.
Led of XJT is fix red and green flashing.
BUT : when i'm changing model , it count . even after a reboot , SWR =0 but telrx counting. I have no receptor bind with this model.
Led of XJT is fix red and green flashing.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
Make sure all models have the protocol set to PXX, a newly created model will default to PPM.
Also check you have D16 set.
Are you using the BIND option in the menu to bind? If so, when you select this, does the RED LED on the XJT start flashing and the module start beeping?
Mike.
Also check you have D16 set.
Are you using the BIND option in the menu to bind? If so, when you select this, does the RED LED on the XJT start flashing and the module start beeping?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
Yes I deleted all model ; just letting 3 all in PPX D16.
I tried binding with XJT button and by slecting BIND , Yes module bip and vibrate , led flash.
Still won't bind. FW Won't flash either
I tried binding with XJT button and by slecting BIND , Yes module bip and vibrate , led flash.
Still won't bind. FW Won't flash either
Re: SPort device updating
I was wondering : Can the TX lipo has anything to do with this problem ? I am using a 3S lipo (s*** brand) , Tx says 11.2V when I was trying to flash.
(I may be totally wrong , As I tried to flash XSR by powering it on 5V from FC )
(I may be totally wrong , As I tried to flash XSR by powering it on 5V from FC )
Re: SPort device updating
Receivers are rated for 10V max, you should use the original battery.
Flashing with external power will not work as the timing is critical, the radio powers the receiver on right when needed.
Flashing with external power will not work as the timing is critical, the radio powers the receiver on right when needed.
Re: SPort device updating
? There was no original battery with the turnigy 9xr , hobbyking says lipo 3S for this radio ?
When I tried flashing XJT , it was of course powered by the radio, but nothing changed, Device was not found.
When I tried flashing XJT , it was of course powered by the radio, but nothing changed, Device was not found.
Re: SPort device updating
Ah, of course, I didn't read the entire thread, missed that you were on a 9XR pro.
Re: SPort device updating
I can't find someone with the same problem than me.. I really don't understand. I think I will try a complete erase of the 9XR , maybe a change a setting that **** the flashing portocle on Sport.
Re: SPort device updating
There should be no setting involved in that function.
The radio could have a hardware issue that prevents it from sending data on the smart port.
The radio could have a hardware issue that prevents it from sending data on the smart port.
Re: SPort device updating
When data is send on the smart port appart from flashing function ? => Could I check that there sata on my smartport ?
Re: SPort device updating
Never, AFAIK the smart port update is currently the only function that uses data out. You could look for output with an oscilloscope or a serial -> USB adapter.
Re: SPort device updating
Ok , I got an brand new arduino nano v3 , I may also trying to flash my Xjt and XSR with it . I have to find a tutorial of info about if somebody already did it.
Re: SPort device updating
Impossible to do it with arduino so I will get a true FTDI232 chip to do it ot buy a frsky cable.
Last chance , I saw that telemetry was COM 2 so i corrected id , maybe a paramater is still wrong and prevent to flash anything on Sport ?
Can you check one last time please ?
Last chance , I saw that telemetry was COM 2 so i corrected id , maybe a paramater is still wrong and prevent to flash anything on Sport ?
Can you check one last time please ?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: SPort device updating
I've just posted a specific test version of the ersky9x for the 9XR-PRO on the test versions thread called "ersky9xr_romSpTest.bin".
On power up, this drives out a signal on the SPort pin, and checks it is changing by reading the SPort input. If the test fails, you should get an Alert saying "SPort Output Self Test Failure".
Due to the hardware design, I can't actually test for a failure, but I can see the signal for this test on my 'scope.
If you had telemetry on COM2, this might explain why the debug TelRxCount value wasn't counting. Have another check for that please.
Mike.
On power up, this drives out a signal on the SPort pin, and checks it is changing by reading the SPort input. If the test fails, you should get an Alert saying "SPort Output Self Test Failure".
Due to the hardware design, I can't actually test for a failure, but I can see the signal for this test on my 'scope.
If you had telemetry on COM2, this might explain why the debug TelRxCount value wasn't counting. Have another check for that please.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: SPort device updating
I'm sorry to bother you again , but I flash the test rom , but it do nothing when I powered it up (I mean that no pop up, it's a normal power up , with loading screen , then display my normal telemetry screen of my model)
I went to telemetry but I lost voltage ( heard a "reboot") and then come back to 11v. But nothing more. What I have to to to run the test ?
Thanks
I went to telemetry but I lost voltage ( heard a "reboot") and then come back to 11v. But nothing more. What I have to to to run the test ?
Thanks