SKY9x Introduction
SKY9x Introduction
Here is the Rev 3.0 Version of the SKY9x Upgrade Board
This is the Final design , that has been sent out for Fabrication.
I have ordered 125 boards .... and about 80 are spoken for so far...
The boards are due in two weeks , then off to the SMT assembly house...
If all goes well , I hope to start shipping them by the end of November.
-Brent
This is the Final design , that has been sent out for Fabrication.
I have ordered 125 boards .... and about 80 are spoken for so far...
The boards are due in two weeks , then off to the SMT assembly house...
If all goes well , I hope to start shipping them by the end of November.
-Brent
Re: SKY9x Introduction
Aha,
A nice new toy for Christmas perhaps
Good work Brent!
A nice new toy for Christmas perhaps
Good work Brent!
Re: SKY9x Introduction
Looks great, I can't wait.
-Gohst
-Gohst
Re: SKY9x Introduction
Time to order my 2nd BT module from ebay.
Re: SKY9x Introduction
Can you recommend one? Time to start gathering the parts
Re: SKY9x Introduction
I used this one with the Ver B board and working. I will get one again for the V3:
http://www.ebay.com/itm/Wireless-Serial ... 53eb8e2d89
http://www.ebay.com/itm/Wireless-Serial ... 53eb8e2d89
Re: SKY9x Introduction
Brent: Do you have schematics to go with the above diagram?
Re: SKY9x Introduction
Here is the Schematic
The schottky diode are being changed , the leakage is too high on the MBRX140
-Brent
The schottky diode are being changed , the leakage is too high on the MBRX140
-Brent
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: SKY9x Introduction
Is D9 the one to stop the coin cell from discharging to fast? What diodes should be changed and what's a good retrofit replacement. SMD or otherwise?SkyNorth wrote:Here is the Schematic
The schottky diode are being changed , the leakage is too high on the MBRX140
-Brent
SM
Re: SKY9x Introduction
The diodes on the Co-processor , are going to be changed to
BAT42W types , these have a leakage in the order of 500nA where as the MBRX140s' leakage is 300uA
This is almost 1000 times lower....
The higher the current rating , the more leakage it seams...
The BAT42W are rated at 200mA , which is more than enough for the task at hand.
-Brent
BAT42W types , these have a leakage in the order of 500nA where as the MBRX140s' leakage is 300uA
This is almost 1000 times lower....
The higher the current rating , the more leakage it seams...
The BAT42W are rated at 200mA , which is more than enough for the task at hand.
-Brent
Re: SKY9x Introduction
Is it possible to retrofit the BAT42W to VerB board without other changes?
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: SKY9x Introduction
Also how many do we want to change out. 2 for sure if only the 2032 battery is used?
DigKey $.44ea
http://www.digikey.com/product-detail/e ... -ND/717817
ShowMaster
Sent from my iPod touch using Tapatalk
DigKey $.44ea
http://www.digikey.com/product-detail/e ... -ND/717817
ShowMaster
Sent from my iPod touch using Tapatalk
Re: SKY9x Introduction
I would wait and see how long the battery lasts now , before changing them.
The diodes are the same foot print , so they will fit.
-Brent
The diodes are the same foot print , so they will fit.
-Brent
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: SKY9x Introduction
Thanks Brent.
I'll do that for both boards and report the time they last.
ShowMaster
Sent from my iPod touch using Tapatalk
I'll do that for both boards and report the time they last.
ShowMaster
Sent from my iPod touch using Tapatalk