HK450 Heli with very soft start (HK ESC). Plus sw warnings.

If you have a model config you would like to share. Post it here!
Post Reply
User avatar
njozsef
Posts: 29
Joined: Tue Jan 24, 2012 2:00 pm
Country: -
Location: Hungary

HK450 Heli with very soft start (HK ESC). Plus sw warnings.

Post by njozsef » Thu Jan 26, 2012 1:13 pm

This template demonstarte how to apply soft start, if not supported own ESC.
Warning signal on, if throttle cut active but flight mode switch not ID0.
Warning signal on, if Gyro not switched headlock mode.

Original source: random sweep.

ch1,2,3 = AIL, ELE, PIT servos
ch4 = rudder servo (to GYro in)
ch5 = THR (ESC)
ch6 = Gyro sensitivy
ID0= 1 idle0, -2° pith hold, cyclic is normal (c1,c4) (if c4 and c1 curve modify the flmode is normal for idle0) (pitch curve= c4)
ID1 =1 idle1, curve (c2) (pitch curve= c5)
ID2 = 1 idle2, curve (c3) (pitch curve= c6)
THR switch = Throttle cut.
ch11 pitch servo (virtual channel)

if gear=1 (rate mode) then warning audio.
if THR sw=0 and id1 or id2=1 then warning soud active (motor off but flight mode not id0)
if ID0=1 and THR switch=1 then ignition (slow start).

modify ch1,2,3 and ch11 to collective and ciclyc pitch.

ch15, ch16, sw1, sw2 = soft start slave ch and sw
sw3, sw4, sw5 = warning sign switch (idle0,1,2)
Attachments
HELI450_very_slow_start_(HK ESC).eepe
(4.84 KiB) Downloaded 668 times
Last edited by njozsef on Sun Jul 08, 2012 8:23 pm, edited 1 time in total.


User avatar
njozsef
Posts: 29
Joined: Tue Jan 24, 2012 2:00 pm
Country: -
Location: Hungary

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin

Post by njozsef » Fri Jan 27, 2012 8:16 pm

valid (flying and fine tuned) ALIGN 450 setup
please check and fix the limits, trim, throttle curves, pitch curves, subtrim and rudder direction.

switch:
id0=ignition start mode
id1 id2 3d setup middle and high rpm.
thottle cut= motor on/off
elev and ail= low/mid/high expo
gear=gyro mode rate/headlock
trainer= light on

cv1= start throttle curve
cv2, cv3 = id0, 1 throttle curve
cv4,5,6 = id1,2,3 pitch curve
Attachments
real_HELI450_very_slow_start_(HK ESC).eepe
(4.84 KiB) Downloaded 562 times

mrspeed
Posts: 2
Joined: Tue Feb 28, 2012 8:27 am
Country: -

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin

Post by mrspeed » Sat Jun 23, 2012 8:03 pm

Hello,
I'm a beginner on CP helis,
I try to programm my T9x for a 450 3D heli, evrything looks good so far, only pitch has to be converted.
How can I do this, must I reverse al 3 servos ?

mrspeed
Posts: 2
Joined: Tue Feb 28, 2012 8:27 am
Country: -

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin

Post by mrspeed » Sat Jun 23, 2012 8:16 pm

My main problem is which servo is aileron/elevator/pitch ?
I mean which servo is cyc1/2/3 on my 120 deg swash plate ?
I have ER9x

User avatar
njozsef
Posts: 29
Joined: Tue Jan 24, 2012 2:00 pm
Country: -
Location: Hungary

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin

Post by njozsef » Mon Jun 25, 2012 4:38 pm

This attachments working for trex (or clone) 450 heli.
Please download.

please settings the
heli swash type on heli menu.


Measuredpath
Posts: 32
Joined: Fri Jun 22, 2012 5:21 am
Country: -

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin

Post by Measuredpath » Sat Jul 07, 2012 6:49 am

Do you have the file so I can open it up on the Mac version of this software? I have windows on my mac as well, I just prefer not to do anything in that OS

User avatar
Kilrah
Posts: 10036
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnin

Post by Kilrah » Sat Jul 07, 2012 8:07 pm

The file is the same whether you use the Win, mac or linux version of eepe.

If you use eepe you'd better use the Windows version, as the Mac version is outdated and doesn't support the current er9x revision. If you use companion9x both versions are in sync.

User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnings.

Post by silversurfer48 » Sat Apr 09, 2016 6:35 am

:HK450 Heli with very soft start (HK ESC). Plus sw warnings.:

I flashed your eepe everything seems to do the right move except my motor it dont turn on. My 450 Esky belt cp version 1 I have been racking my brain for 2 days :oops: Im to close can you maybe give me some ideas were it may be failing or what is in the wrong place?
Last edited by silversurfer48 on Sat Apr 09, 2016 6:38 am, edited 1 time in total.

User avatar
MikeB
9x Developer
Posts: 16507
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnings.

Post by MikeB » Sat Apr 09, 2016 8:37 am

The original post says the THR switch is "Throttle cut". Just checking you have your THR switch in the correct direction.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
Kilrah
Posts: 10036
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: HK450 Heli with very soft start (HK ESC). Plus sw warnings.

Post by Kilrah » Sat Apr 09, 2016 10:57 am

That file is 4 years old, for a plain 9x, and we don't even know for what firmware. It could be horribly broken on whatever current software you're trying to use it with. Actually it won't even open with eepskye set to 9Xtreme, so as I believe that's the radio you have I don't even know how you get anything to work.

Please be careful, helis can bite badly and it takes care to get everything right. Don't do anything you don't understand.


Post Reply

Return to “Template Library”