- In the wiki diagram it says to cut the tracks where indicated with the red marker. However, it's not clear to me exactly where to cut. The top red mark looks like it's cutting only half of the track? And the bottom mark looks like it's in between two tracks? Could someone clarify exactly where to cut?
- Is exactly 390ohm resistor required for the connection to the cpu pin? I have 220ohm or 470ohm, would either of those work instead?
- And is 4.7u the same as 4.7uF?
Haptic Questions
Haptic Questions
I'm going to be adding in a piezo speaker and vibrator motor for the haptic feedback mod and before I began have a few questions.
Re: Haptic Questions
The dark part is not the track. The lighter colored parts are where the copper is under the green coloring.
I can't answer the resistor question.
Yes to #3 the capacitor question
I can't answer the resistor question.
Yes to #3 the capacitor question
Re: Haptic Questions
Thanks, it appears that my board is of the different version that in the above diagram. :/
- cre8tiveleo
- Posts: 1434
- Joined: Tue Dec 27, 2011 6:13 pm
- Country: -
- Location: Ontario,(GTA North)
- Contact:
Re: Haptic Questions
The 4.7uF is beside the cap marked 4.7u (in the green) , so.. yes.. it's the same.
The resistor is used to lower current flow , either should work, the higher the resistance the lower the power, the lower the resistance, the higher the power.
Like an led, you need a resistor on the cathode when hooking it up to a voltage supply. The larger the resistor, the dimmer the led is, the smaller the resistance, the brighter it is.
The resistor is used to lower current flow , either should work, the higher the resistance the lower the power, the lower the resistance, the higher the power.
Like an led, you need a resistor on the cathode when hooking it up to a voltage supply. The larger the resistor, the dimmer the led is, the smaller the resistance, the brighter it is.
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Haptic Questions
I will get a new image for this alternative board up today.
Seems to be that more tx's have the alternative board
Sent from my iPhone using Tapatalk
Seems to be that more tx's have the alternative board
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: Haptic Questions
I saw the new image in the wiki. That's the same version board as the image I posted in this thread. I'm confused??
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Haptic Questions
In which case.... You have cut tracks that dont need cutting
Solder bridge the cuts... And follow the new image.
Sent from my iPhone using Tapatalk
Solder bridge the cuts... And follow the new image.
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: Haptic Questions
I haven't done any modding yet. I'm just confused because the two boards in the wiki look exactly the same. My board has a slightly different layout (there's pictures of it in the other haptic thread).
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Haptic Questions
Look closer . They are different.
The change is related to the pin used to drive the haptic.
Sent from my iPhone using Tapatalk
The change is related to the pin used to drive the haptic.
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: Haptic Questions
I see what you mean. However, the actual board looks the same. My board doesn't look like that.
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Re: Haptic Questions
Ok.. so I am officially an idiot!
Just checked the wiki images and I have posted the wrong one!! Now I understand your confusion.
I am out most of today - will try sort a new out a new one tomorrow.
Rob
Just checked the wiki images and I have posted the wrong one!! Now I understand your confusion.
I am out most of today - will try sort a new out a new one tomorrow.
Rob
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: Haptic Questions
No problem!
Thanks for all your help. I'll be looking forward to the correct one!
Thanks for all your help. I'll be looking forward to the correct one!
Haptic Questions
Any news on the new diagram?
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Haptic Questions
Sorry... Been caught up with work. Have to work all w/end, so guess I will be unable to sort this before next week
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Haptic Questions
That's okay. I'm just excited to start the mod!
Haptic Questions
My buddy setup his new 9x with the new revision speaker board using the picture and diagram from the other thread. It is working good.
viewtopic.php?t=406
viewtopic.php?t=406
Re: Haptic Questions
Well i just followed that guide and it seems to be working! I get vibration for things like, center trims, new model, low voltage alarm, etc.
However I wish the pezio buzzer was a bit louder. This is the one I installed: http://www.ebay.com/itm/220951641092?ss ... 1504wt_905
Does that seem like a decent one?
However I wish the pezio buzzer was a bit louder. This is the one I installed: http://www.ebay.com/itm/220951641092?ss ... 1504wt_905
Does that seem like a decent one?
Re: Haptic Questions
Have you opened the holes under the speaker grill in the front of the body. I drilled a few small holes in mine and the sound is much louder, although I'm using a speaker from a greetings card, looks very much like the one in cheeto's thread.
Re: Haptic Questions
Well that could be it, but I don't think so. It seems that the stock speaker might have been even louder than this one.
Just a thought, I didn't have exact resistor matches so I used a 1.1K instead of 1k and 470ohm instead of the 390ohm. Could either of these changes make it be more quiet?
Just a thought, I didn't have exact resistor matches so I used a 1.1K instead of 1k and 470ohm instead of the 390ohm. Could either of these changes make it be more quiet?
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Haptic Questions
I have tried numerous piezo speakers. Not all are loud as each other - so best to try a few
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: Haptic Questions
Okay, well then I guess I'll try others. Maybe I'll buy a card and use the speaker from that like some other guys on here have done.
Re: Haptic Questions
I don't know where you're from but I've used 6 of these in 9x's and they seem to work well. I haven't heard any complaints about volume.
http://www.radioshack.com/product/index ... Id=2062397
http://www.radioshack.com/product/index ... Id=2062397
Re: Haptic Questions
Very nice! I have Radioshack locally so I might just stop by and pick that up. Thanks.