Turnigy 9x with Flysky TH9x main board

Where to find parts? Refactoring your entire transmitter, new cases? Sticks etc..
egpurusotaman
Posts: 16
Joined: Sat Nov 18, 2017 3:50 am
Country: -

Re: RE: Re: Turnigy 9x with Flysky TH9x main board

Post by egpurusotaman »

jhsa wrote:The orange capacitor near the Crystal. Just remove it..

João

Sent from my BLN-L21 using Tapatalk
Do I need to replace the 16MHz Crystal (hy16.000) or the capacitors(J476).
What is the voltage should it receive while connected...Image

Sent from my Redmi Note 4 using Tapatalk
Last edited by egpurusotaman on Sat Nov 25, 2017 12:16 pm, edited 1 time in total.

egpurusotaman
Posts: 16
Joined: Sat Nov 18, 2017 3:50 am
Country: -

Re: Turnigy 9x with Flysky TH9x main board

Post by egpurusotaman »

Also pls let me know, how to check the processor is getting power...
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Turnigy 9x with Flysky TH9x main board

Post by jhsa »

I will, but only later after work.. Don't have access to my PC at the moment..

João

Sent from my BLN-L21 using Tapatalk

My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
egpurusotaman
Posts: 16
Joined: Sat Nov 18, 2017 3:50 am
Country: -

Re: RE: Re: Turnigy 9x with Flysky TH9x main board

Post by egpurusotaman »

jhsa wrote:I will, but only later after work.. Don't have access to my PC at the moment..

João

Sent from my BLN-L21 using Tapatalk
Waiting....


Sent from my Redmi Note 4 using Tapatalk

User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Turnigy 9x with Flysky TH9x main board

Post by jhsa »

Sorry, forgot it completely. Thanks for reminding me.. Please see attached picture.
Red is 5V, black is ground.


João
Attachments
9X Board_Chip_Vcc and Gnd.jpg
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

egpurusotaman
Posts: 16
Joined: Sat Nov 18, 2017 3:50 am
Country: -

Re: Turnigy 9x with Flysky TH9x main board

Post by egpurusotaman »

Sorry for the late reply...Didnt get time to check the board....

I checked all the input voltage to the processor, its all 5v perfectly....
I also checked the J476 capacitor and it give the 5v multimeter reading....
5dcd28e7-2d92-4be2-aeea-2746a6404a32.jpg
Planning to replace the Crystal with the attached 16Mhz crystal...
Advice.....???
egpurusotaman
Posts: 16
Joined: Sat Nov 18, 2017 3:50 am
Country: -

Re: Turnigy 9x with Flysky TH9x main board

Post by egpurusotaman »

Advice needed...

Sent from my Redmi Note 4 using Tapatalk

ReSt
Posts: 1581
Joined: Tue Dec 27, 2011 11:34 pm
Country: -

Re: Turnigy 9x with Flysky TH9x main board

Post by ReSt »

egpurusotaman wrote: Tue Dec 05, 2017 6:44 pm
I also checked the J476 capacitor and it give the 5v multimeter reading....
You should try with the capacitor removed.
The problem is not a short of the capacitor but a to high capacity for the programmer ( IIRC the programmer must do a reset against the load of the capacitor. And if the capacity is (too) high or the signal of the programmer is to weak, the reset is not done within the time the programmer expects and therefor programming fails)

That crystal should work if you get it onto the pads without bending the pins to hard.

Reinhard

Post Reply

Return to “Hardware Mods”