New Frsky Hall Effect Gimbals

Post Reply
lancaster
Posts: 182
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

New Frsky Hall Effect Gimbals

Post by lancaster » Wed Jan 18, 2017 12:03 pm

Hi Guys

Can these gimbals be fitted to the T9X Extreme?

regards
Hans

User avatar
bob195558
Posts: 1901
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: New Frsky Hall Effect Gimbals

Post by bob195558 » Wed Jan 18, 2017 2:40 pm

Hi lancaster,

Can you link to where these New FrSky Hall Effect Gimbals are (can be found) ?

Bob B.
ErSky9x on Taranis, Sky9x, 9Xtreme, Er9x on 9x with Smartieparts Programmer with TelemetrEZ Board
3D Printing: (http://openrcforums.com/forum/viewforum.php?f=85)

Suncoaster
Posts: 216
Joined: Thu Dec 29, 2011 10:18 am
Country: Australia
Location: Cooloola Cove, Australia

Re: New Frsky Hall Effect Gimbals

Post by Suncoaster » Wed Jan 18, 2017 3:02 pm

Try here : /www.horusrc.com/en/new-frsky-m9-high-se ... -plus.html. I don't think they are available just yet.

Dave

lancaster
Posts: 182
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: New Frsky Hall Effect Gimbals

Post by lancaster » Wed Jan 18, 2017 3:48 pm

bob195558 wrote:Hi lancaster,

Can you link to where these New FrSky Hall Effect Gimbals are (can be found) ?

Bob B.
Hi Bob

The gimbals are also shown on the Banggood site

https://goo.gl/hCkeFg
Hans

User avatar
bob195558
Posts: 1901
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: New Frsky Hall Effect Gimbals

Post by bob195558 » Wed Jan 18, 2017 3:56 pm

FRSKY HORUS X12S GIMBAL ($60.00): (https://www.horusrc.com/en/receivers-ac ... imbal.html).

Edit: Then these are not the ones you were referring too.
The link above was not working, I fixed the link, works now.

Bob B.
Last edited by bob195558 on Thu Jan 19, 2017 3:07 pm, edited 2 times in total.
ErSky9x on Taranis, Sky9x, 9Xtreme, Er9x on 9x with Smartieparts Programmer with TelemetrEZ Board
3D Printing: (http://openrcforums.com/forum/viewforum.php?f=85)


Suncoaster
Posts: 216
Joined: Thu Dec 29, 2011 10:18 am
Country: Australia
Location: Cooloola Cove, Australia

Re: New Frsky Hall Effect Gimbals

Post by Suncoaster » Thu Jan 19, 2017 2:38 pm

bob195558 wrote:FRSKY HORUS X12S GIMBAL ($60.00): (ttps://www.horusrc.com/en/frsky-horus-x12s-gimbal.html).

Edit: Then these are not the ones you were referring too.

Bob B.
Hi Bob, your link does not work for me, but the link I posted and the link Lancaster posted are both for the same item.

Dave

User avatar
bob195558
Posts: 1901
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: New FrSky Hall Effect Gimbals (M9 Hall Effect Gimbals)

Post by bob195558 » Thu Jan 19, 2017 3:09 pm

Thanks Dave, I fixed the link, it works now.

Edit: M9 Hall Effect Gimbal, see here for more info: (viewtopic.php?f=122&t=9683).
There is a Problem, with the voltage for the FlySky and Turnigy 9x Radios which use 5Vs with there Gimbals circuit. :?:

Bob B.
Last edited by bob195558 on Tue Jan 24, 2017 12:58 pm, edited 1 time in total.
ErSky9x on Taranis, Sky9x, 9Xtreme, Er9x on 9x with Smartieparts Programmer with TelemetrEZ Board
3D Printing: (http://openrcforums.com/forum/viewforum.php?f=85)

Hertz
Posts: 72
Joined: Wed Sep 30, 2015 2:14 pm
Country: -

Re: New Frsky Hall Effect Gimbals

Post by Hertz » Sun Jan 22, 2017 6:14 pm

Seems like we'll have to add a stepdown, or maybe 9xtreme can provide 3.3V?

User avatar
jhsa
Posts: 18128
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: New Frsky Hall Effect Gimbals

Post by jhsa » Sun Jan 22, 2017 6:26 pm

When you install the 9xtreme the gimbals connect to it anyway, so they will be supplied with 3.3V

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Hertz
Posts: 72
Joined: Wed Sep 30, 2015 2:14 pm
Country: -

Re: New Frsky Hall Effect Gimbals

Post by Hertz » Sun Jan 22, 2017 6:32 pm

Awesome, thanks. I have nearly ordered a 3.3V Pololu in the meantime :)
Seems like M9 are than Aurora 9x, if I install the Aurora gimbals while M9 are in transit, I'll have issues installing them later?

User avatar
bob195558
Posts: 1901
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: New Frsky Hall Effect Gimbals

Post by bob195558 » Sun Jan 22, 2017 6:36 pm

MikeB wrote:Note that the SKY board, AR9X board, 9Xtreme and 9XR-PRO are all 3.3V based and only supply 3.3V to the gimbal pots.
Mike.
MikeB wrote:
bob195558 wrote:10 bits down to 6.6 bits, would this, in actually = 6 bits only or can it use the .6 bits ? :?:
You are not down to 6.6 bits more like 9.3 bits.

We use some over sampling with averaging to turn the 10 bits into 11 bits already.
I just tried moving a stick on a Taranis (12 bits analog), and I'm struggling to get the output to change by less than 0.3%.
I wouldn't be surprised to find a resolution of 680 steps on a stick is actually OK.
When I put a 'scope on the PPM output of my Hitec Eclipse 7, I found the pulse width changed in steps of 2.5uS. Since full movement of the stick in one direction only changed the pulse width by 400uS, this was only 320 steps across the full range of stick movement.
Mike.
M9 Hall Effect Gimbal, see here for more info: (http://openrcforums.com/forum/viewtopic ... 122&t=9683) and here: (http://openrcforums.com/forum/viewtopic.php?f=97&t=9609) and (http://openrcforums.com/forum/viewtopic.php?f=95&t=9977).
Last edited by bob195558 on Fri Mar 03, 2017 2:30 am, edited 1 time in total.
ErSky9x on Taranis, Sky9x, 9Xtreme, Er9x on 9x with Smartieparts Programmer with TelemetrEZ Board
3D Printing: (http://openrcforums.com/forum/viewforum.php?f=85)

RightRudder
Posts: 241
Joined: Tue Jan 15, 2013 9:41 pm
Country: -

Re: New Frsky Hall Effect Gimbals

Post by RightRudder » Fri Jan 27, 2017 9:31 pm

Does anybody know if the X12 gimbal frames will fit in Taranis? I'm glad the M9 gimbals will work in both my Taranis and 9X (with Sky board) but the X12 gimbals seem a bit better made with all metal frames.

User avatar
Kilrah
Posts: 9665
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: New Frsky Hall Effect Gimbals

Post by Kilrah » Fri Jan 27, 2017 9:39 pm

They don't.

User avatar
bob195558
Posts: 1901
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: New Frsky Hall Effect Gimbals

Post by bob195558 » Tue Jan 31, 2017 2:43 pm

Here are two reviews of the new M9 Hall Sensor Gimbals by BMSWEB: FrSky Taranis M9 Hall Sensor Gimbals | Flight Test
(https://www.youtube.com/watch?v=NvawANhxUos).
Taranis upgrade M9 Hall Sensor Gimbals.jpg
Upgrade M9 Hall Sensor Gimbals
And the second one: FrSky Taranis M9 Hall Sensor Gimbals | Stick Height Adjustment
(https://www.youtube.com/watch?v=CWeP4vABSRE).

Bob B.
ErSky9x on Taranis, Sky9x, 9Xtreme, Er9x on 9x with Smartieparts Programmer with TelemetrEZ Board
3D Printing: (http://openrcforums.com/forum/viewforum.php?f=85)

RightRudder
Posts: 241
Joined: Tue Jan 15, 2013 9:41 pm
Country: -

Re: New Frsky Hall Effect Gimbals

Post by RightRudder » Tue Jan 31, 2017 3:09 pm

Does anybody know the thread on these sticks? Is it M3?

Edit: The second review says they are 3mm.

User avatar
bob195558
Posts: 1901
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: New Frsky Hall Effect Gimbals

Post by bob195558 » Tue Jan 31, 2017 4:17 pm

New Upgrade M9 Hall Sensor Gimbals_m9g.jpg
M9 Gimbal
This part of the new M9 Gimbal, looks to be sticking up a lot.
Will this be a problem with the SKY board, AR9X board, 9Xtreme, 9XR-PRO using the FlySky and Turnigy 9x radio cases ? :?:
More M9 Hall effect gimbals info here: (viewtopic.php?f=122&t=9683#p123428).

Bob B.
ErSky9x on Taranis, Sky9x, 9Xtreme, Er9x on 9x with Smartieparts Programmer with TelemetrEZ Board
3D Printing: (http://openrcforums.com/forum/viewforum.php?f=85)

Post Reply

Return to “9Xtreme upgrade board”