Upgrade 3 Position Switch Mod 9Xtreme

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Jan 30, 2016 4:34 pm

Upgrade 3 Position Switch Mod 9Xtreme

Hi,
This Mod is to upgrade the 9Xtreme radio's 2 position switch to a 3 Position Switch. :D
I have not done this mod yet and so I am learning to do this mod also.
I do not having a proper visualization in my mind (yet) to Which Wire Goes Where,
I will need help in completing this upgrade.


The 2-Position Switch I have chosen to upgrade first is the ELE (Elevator Switch) to the left side of the 9Xtreme Radio.
2 position ELE SW_a.jpg
2 position ELE SW left side_a
Note: Do not trust the wire colors as the 9x radio's may have different
wire colors for what the wire is used for between different 9x Radios
.
2 position ELE SW_b.jpg
Inside showing 2 position SW wiring.
3 Position Switch_c.jpg
3 Position Switch to be installed.
The next photo shows where the EXT # pins are located on the stock 9x radio's main board.
I believe I need to Use one of the EXT # to connect to the top terminal of the 3-Position Switch.
This is where I am not sure Which Wire Goes Where and need some help. :? :?:
Main Board 3 Position Switch Pins_d.jpg
Location of EXT # Pins.
Any of the EXT # pins can be used for the 3 Position Switch Upgrade Mod.
WARNING: If you are upgrading the Throttle and/or the Turn Switch to a 3-Position Switch, do NOT trust
that your 9x Radio's Ground Wire is connected to the center switch terminal of these stock switches.
9X Radio's do not use any normal discipline of World Wiring Codes to guide there wiring practices.
It will help you to identify which of these wires are the Ground wire, which the Ground wire will need
to be connected to the switch center terminal of your new 3-Position Switch for it to work properly.



See here for more 9Xtreme information: (viewtopic.php?f=95&t=7182).

Here is info about setting up text file (Model Notes) on the SD card also:
(viewtopic.php?f=126&t=8443&start=30#p112)
and (viewtopic.php?p=112368#p112344).

Bob B.
Last edited by bob195558 on Fri Mar 11, 2016 10:08 pm, edited 7 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).


User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Jan 30, 2016 4:59 pm

Hi,
Is the center Switch terminals where the ground wire is connected and also why they are able to be connected with other center switch terminals together ? :?:

Bob B.
Last edited by bob195558 on Wed Jun 29, 2016 8:33 pm, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
jhsa
Posts: 19111
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by jhsa » Sat Jan 30, 2016 6:51 pm

Ground to center, solder the existing switch wire to the bottom pin (that's ID0). solder the new EXTx wire to the top pin of the new switch. See green text at top Right..
I should add to the text that ground must be connected to the middle pin and the original wire to the bottom pin. maybe I didn't because on my radio it was already like that ;) :)

João
Attachments
10-Prepare mainboard_BL_3Pos.jpg
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Jan 30, 2016 8:38 pm

Hi João,
Thank you, this helps a lot.
I made this photo showing the wiring connections.
3 Position Switch connections_cc.jpg
3 position switch wire connections.
The old Taranis Gimbals connectors (white plugs) do fit, so I will use them to make the EXT pin connections.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
jhsa
Posts: 19111
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by jhsa » Sat Jan 30, 2016 8:46 pm

bob195558 wrote: The old Taranis Gimbals connectors (white plugs) do fit, so I will use them to make the EXT pin connections.

Bob B.
that's why on my build I said that we should save the original taranis gimbals's plugs ;) :)

Would you mind if I steal your photo?

Thanks

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW


User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Jan 30, 2016 9:43 pm

Please DO USE it! as it is an open source photo! :lol: ;)

Bob B.
Last edited by bob195558 on Sun Feb 14, 2016 5:48 pm, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
jhsa
Posts: 19111
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by jhsa » Sat Jan 30, 2016 10:14 pm

ha ha ha.. :mrgreen: Thanks ;)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Mon Feb 01, 2016 3:09 pm

When I was replacing the 2-position ELE switch, I also decided to replace the 2-position RUD switch at the same time.
I soldered the 9x Radio wires to there proper BOTTOM terminals of the 3-position switches.
Then soldered the 9x Ground wires to the CENTER terminal of the 3-position switches which share the same Ground wires.
Then for the ELE switch I used the EXT4 pin and soldered it to the TOP terminal of the ELE 3-position switch.
And then for the RUD switch I used the EXT3 pin to the TOP terminal of the RUD 3-position switch.
EXT4 EXT3 to ELE RUD.jpg
EXT4 to ELE SW and EXT3 to RUD SW
3 position sw connections_ccc.jpg
Wire connections to the 3-Position Switches ELE and RUD
I then powered up the 9Xtreme radio to check for any smoke and all was good. :D
Next to make the proper hardware setting changes in the 9Xtreme firmware,
I followed the procedure below to open the Hardware Menu:
Hold the left horizontal trim to the left while turning ON the Radio.
Note, only need to hold the left horizontal trim for a second or so, this will allow you to open the Hardware menu.
The Hardware menu will be found in Radio Setup.
With the Hardware menu now open I scrolled through the Hardware menu until I found the ELE switch and set it to EXT4
and then went to the RUD switch and set it to EXT3.
ELE sw to EXT4.jpg
Set ELE sw to EXT4 and RUD sw to EXT3
Next exit the menus and power off the radio and then power the radio back ON.

I then checked the ELE and RUD switch position indicator Arrows (symbols ^ - v) and they are showing the proper switch positions.
ELE RUD sw position indicators_Back.jpg
Switches in Back Positions
ELE RUD sw position indicators_Center.jpg
Switches in Center - Positions
ELE RUD sw position indicators_Forward.jpg
Switches in Forward Positions
:)

Bob B.
Last edited by bob195558 on Wed Jun 29, 2016 10:33 am, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
jhsa
Posts: 19111
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by jhsa » Mon Feb 01, 2016 4:54 pm

Well done.. :mrgreen:

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Feb 13, 2016 8:53 pm

Hi Mike,
I just upgrade the THR SW to a 3-Position Switch and connected it to EXT8.
But when the THR SW is in the third SW position it still only shows - center position.
The Third position seem to be not working.
The First and Second positions are working.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
MikeB
9x Developer
Posts: 16686
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by MikeB » Sat Feb 13, 2016 9:13 pm

Plenty of possibilities for the labelling of EXT8 to be wrong, I may well have the code wrong somewhere on either the M64 or on the 9Xtreme. Please try setting the switch to EXT7 (and then all the others 6,5,2,1 and see if one of them works.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Feb 13, 2016 10:53 pm

Hi Mike,
I changed THR SW to EXT 7 and same failed results as it had with EXT 8.
Change RUD SW from EXT 7 to EXT 8 and it is working properly, same as it did when connected to EXT 7.
I will try THR SW to the EXT 3 connection next and report back after this test try.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Feb 13, 2016 11:07 pm

Hi Mike,
I changed THR SW from EXT 7 to EXT 3 with same failed results as it had with EXT 7.
I have also checked the continuity of the upgraded 3-position THR SW and it is good.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
MikeB
9x Developer
Posts: 16686
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by MikeB » Sat Feb 13, 2016 11:30 pm

Could you check the third connection on the new THR switch is switching to ground?
My 9Xtreme has the ELE switch converted to 3-pos on EXT3. As a test, I set the THR switch to also use EXT3.
With the ELE switch in the middle position (EL-), switching the THR switch gives TH^ and TH-.
With the THR switch at TH-, when I switch the ELE switch to ELv, the THR switch shows THv, so I think the firmware is working correctly.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Feb 13, 2016 11:36 pm

Hi Mike,
Tested so far THR SW to EXT 1 and EXT 2 with the same failed results as all the other EXT #'s.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
MikeB
9x Developer
Posts: 16686
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by MikeB » Sat Feb 13, 2016 11:58 pm

It does seem as though there is a problem with the switch itself. Since you know that using EXT3 works with the RUD switch, it should work with the THR switch.
You could try the same test I did. Put you ELE and RUD switches back on EXT4 and EXT3, then set the THR switch to also use one of these. When the THR switch is in the middle, and you switch the RUD or ELE switch down, the THR switch should also show as down (THv). That will confirm the firmware is OK or not.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sun Feb 14, 2016 12:09 am

I will give it a try and I will also recheck my connections, as I could have something not connected properly.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sun Feb 14, 2016 1:45 am

Hi Mike,
Found my error, the 9x radios (China) do not have any color coding with there wiring.
The two wire colors are light brown and faded orange which almost look like the same color.
I wrote down the wire colors of each wire terminal position, but made an error, soldering the ground wire to the outer terminal causing the problem.

Have corrected the problem and now is working properly. :D
Thank you for your help, sorry to have made the error.

Bob B.
Last edited by bob195558 on Sat Feb 27, 2016 4:44 pm, edited 2 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sun Feb 14, 2016 2:43 am

Hi Mike,
Thinking about it, I believe I did transfer the original 2-Position Switch wires to the new 3-Position Switch terminal connections to be the same.
I am feeling confident that this 9x radio had the ground wire connected to the outer terminal
and by being wired this way for a 2-Position Switch it would work this way.

So in hind sight, it would have been better to have check which wire was the ground wire before transferring the two original wires
to the new 3-Position Switch terminals . (Ground wire needs to be connected to the center Switch terminal.)

Bob B.
Last edited by bob195558 on Sat Feb 27, 2016 4:49 pm, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sun Feb 14, 2016 5:27 pm

WARNING: If you are upgrading the Throttle and/or the Turn Switch to a 3-Position Switch, do NOT trust
that your 9x Radio's Ground Wire is connected to the center switch terminal of these stock switches.
9X Radio's do not use any normal discipline of World Wiring Codes to guide there wiring practices.
It will help you to identify which of these wires are the Ground wire, which the Ground wire will need
to be connected to the switch center terminal of your new 3-Position Switch for it to work properly.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

lancaster
Posts: 196
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by lancaster » Sat Feb 27, 2016 1:12 pm

bob195558 wrote:WARNING: If you are upgrading the Throttle and/or the Turn Switch to a 3-Position Switch, do NOT trust
that your 9x Radio's Ground Wire is connected to the center switch terminal of these stock switches.
9X Radio's do not use any normal discipline of World Wiring Codes to guide there wiring practices.
It will help you to identify which of these wires are the Ground wire, which the Ground wire will need
to be connected to the switch center terminal of your new 3-Position Switch for it to work properly.

Bob B.
Hi Bob
Thanks for the useful instructions
I am just following them for fitting 3 pos switches to my 9Xtreme
You warn that the ground wire isnt always connected to the centre pin of the switch and its best to check before fitting the new switch
How do you safely check which wire is the ground wire?
I assume you use a multimeter and test the wires for any voltage from the wire to the ground pin on the 9 pin board connector (pin no 4)
regards
Hans

User avatar
MikeB
9x Developer
Posts: 16686
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by MikeB » Sat Feb 27, 2016 2:04 pm

There is one, 3-pos switch that will have ground on its centre connection. Simply check for continuity (with power off) between that centre connection and the ground connection to the 2-pos switch you are replacing.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
bob195558
Posts: 2154
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by bob195558 » Sat Feb 27, 2016 4:32 pm

When I upgraded two 9Xtreme radios from 2 position switches RUD, ELE and AIL, GEAR to three position switches,
these all were using the center terminal connector for the ground connection.
But when I upgraded the THR switch to a 3 position, I assumed the ground wire would also be the same,
but after several frustrating hours I used a multimeter to identify which wire is the ground wire.
By removing the battery (no power to radio) and using a multimeter to check ground continuity between the 9Xtreme Expansion Grid ground
(pins 3, 8, 13 are all ground connections) and the switch wires, I found that the center switch wire was not the ground wire.
9Xtreme Ex Grid pads_GND.jpg
9Xtreme Expansion Grid pins 3, 8 and 13 are all ground connections.
After correcting this problem the upgrade then worked properly. :D

Added note: pin 11 "Battery Voltage" is switched power, which including the "soft power" switch.
This Voltage is then also switched to the Internal and External modules by transistors controlled by the processor.
Pin 9: (PPM/PXX) is the Internal module connection, Pin 7: + power and Pin 8: GND connection.

Bob B.
Last edited by bob195558 on Mon Apr 25, 2016 11:38 am, edited 2 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.

3D Printing upgrades with (CR10 3D Printer): (http://openrcforums.com/forum/viewforum.php?f=85).

lancaster
Posts: 196
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by lancaster » Sun Feb 28, 2016 11:19 am

Mike and Bob
Thanks for the quick replies/instructions
I understand it fully now
happy flying
regards
Hans

lancaster
Posts: 196
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by lancaster » Tue Mar 08, 2016 11:36 am

Mike
I have another question regarding switch names

I am transfering my flap function from switch ID0 to the rudder switch on the left side of the TX

Is it possible to rename the switches, say from RUD, ELE to A,B,C etc to avoid confusion when setting up various mixes and voice alarms

regards
Hans

User avatar
MikeB
9x Developer
Posts: 16686
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by MikeB » Tue Mar 08, 2016 12:16 pm

For the 9X, the switches are named to match the labels on the Tx itself. I think renaming the switches would lead to more confusion, not less!

I've made a note to look into allowing user re-naming of the switches (like you may do for the sticks).

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

lancaster
Posts: 196
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by lancaster » Tue Mar 08, 2016 12:37 pm

Mike
Thanks for the quick reply

Yes I agree the existing switch names are clear and avoid confusion as the basic set up but perhaps a user only change function in the hardware menu is a useful option - just a thought as I think I may get confused when I reassign a few switches

happy flying
Hans

User avatar
MikeB
9x Developer
Posts: 16686
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by MikeB » Tue Mar 08, 2016 12:56 pm

You might look into the "Model Notes" feature where you may call up some text (from the Sd card) specific to each model. You may put a list there of what each switch does for that model.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

lancaster
Posts: 196
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by lancaster » Tue Mar 08, 2016 2:27 pm

Thanks Mike

I'll try that

regards
Hans

PS JST plugs and wires (ebay China) and 3 Pos switches arrived from RS today - good service

lancaster
Posts: 196
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: Upgrade 3 Position Switch Mod 9Xtreme

Post by lancaster » Fri Mar 11, 2016 11:52 am

Mike
I looked into Model Notes but couldn't see how to add text to the SD card

Could you point me in the right direction?

many thanks
Hans


Post Reply

Return to “9Xtreme upgrade board”