Changement de carte mère surTGYX

ValentinDurand · Post by **ValentinDurand** » Thu Jan 07, 2016 6:12 pm

Bonjour,je vais changer ma carte mère sur mon tx et je vais remettre la carte 9xtreme en place.Es-que ça va redémarrer comme la première fois que je l'ai installée neuve.Merci

Daedalus66 · Post by **Daedalus66** » Fri Jan 08, 2016 12:09 pm

ValentinDurand wrote:Bonjour,je vais changer ma carte mère sur mon tx et je vais remettre la carte 9xtreme en place.Es-que ça va redémarrer comme la première fois que je l'ai installée neuve.Merci

The 9Xtreme is not a replacement for the main board in the 9x but an addition to it. You must have a working transmitter if you are to use the 9Xtreme.

When the 9Xtreme is turned on for the first time it automatically installs ErSky9x as you suggest.

J'espere que cela est utile. Ecrire en francais est difficile sur un iPad anglais avec "autocorrect"

Sent from my iPad using Tapatalk

ValentinDurand · Post by **ValentinDurand** » Fri Jan 08, 2016 3:21 pm

Bonjour,je crois que vous avez mal interprété.
J'ai un TX transformé en 9XTreme.
Je vais changer la carte mère.
Quand je vais le remettre en marche,es qu'il va faire comme la première mise en route de 9XTreme

Daedalus66 · Post by **Daedalus66** » Fri Jan 08, 2016 3:34 pm

Maintenant je vous comprend. Je pense que oui, parce que la nouvelle carte mere n'a pas le "firmw are" necessaire et la carte XT va voir ca. Mais je vais poser la question a Steve de SmartieParts.

Daedalus66 · Post by **Daedalus66** » Fri Jan 08, 2016 3:42 pm

Steve at SmartieParts:

The question concerns a 9x transmitter that has had a 9Xtreme board installed. The owner is now replacing the main board (no reason why is given) and wants to know if the XT board will automatically install ErSky9x when he turns on, as it did with the first board. Or does something have to be done to trigger the process a second time?
I'm assuming the XT board will recognize the need to initialize the setup.
The poster reads English and I'll try to clarify if necessary.

KAL · Post by **KAL** » Fri Jan 08, 2016 3:47 pm

As far as I know the 9Xtreme board tests at every power on
whether the slave firmware is present (on the 9X board) or not.
If not, it (the 9Xtreme board) flashes the 9X board with the required firmware.

Klaus

Post by **jhsa** » Fri Jan 08, 2016 3:54 pm

That is correct..

João

Post by **s_mack** » Fri Jan 08, 2016 5:34 pm

Not that it really matters, but to be clear... the 9Xtreme doesn't flash the 9X with ERSky9X. ErSky9X resides on the 9Xtreme itself. The 9Xtreme flashes the 9X with a special slave firmware allowing the 9Xtreme to utilize the 9X's CPU for certain tasks. And yes, if the 9X's mainboard is replaced then the 9Xtreme will go ahead and flash that one too.

Daedalus66 · Post by **Daedalus66** » Fri Jan 08, 2016 6:52 pm

Thanks for the clarification Steve. Good material for the new ErSky9x Guide annex on the 9XT board.

ValentineDurand: la response a votre question est "Oui". [emoji3]

ValentinDurand · Post by **ValentinDurand** » Sat Jan 09, 2016 9:05 pm

Oui,j'ai bien compris et encore merci à tous pour vos réponses très rapides.

Daedalus66 · Post by **Daedalus66** » Sat Jan 09, 2016 11:03 pm

De rien!

Sent from my iPad using Tapatalk

openrcforums