Receive 9xtreme and Installation
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Receive 9xtreme and Installation
moxieman3864: Try leaving the radio off and plugging in the USB cable. The radio should then start in STM DFU (Device Firmware Update) mode and you should hear the tones on your PC indicating a new USB device has been found. This was used to flash the firmware, so should be tested and working.
If you don't get the tones, then please check the cable is a 'real' USB cable, not a 'charging' cable with not data wires.
If you do get tones, we'll take it from there.
Mike.
If you don't get the tones, then please check the cable is a 'real' USB cable, not a 'charging' cable with not data wires.
If you do get tones, we'll take it from there.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Receive 9xtreme and Installation
Hi moxieman3864,
To help answer some of your other questions you have.
and to find other info see here: (viewtopic.php?f=95&t=7182) and (viewforum.php?f=126).
To setup voices go to your: Model Setup / Voice / Voice Alarms to add your voices .
Bob B.
To help answer some of your other questions you have.
Yes that is correct.moxieman3864 wrote:first off when i go into radio set up it says for ver mod 9xt verv.1946-mike date 26.08.2015 ersky9x r218 is that correct ?
You can use the new er9x manual found here: (viewtopic.php?f=5&t=6473)moxieman3864 wrote:is there a step by step how to manual for when your done installing the 9xtreme board ?
and to find other info see here: (viewtopic.php?f=95&t=7182) and (viewforum.php?f=126).
You need to down-load "Voice Pack for Ersky9x_16Khz" then unzip and place folder named "voice" on to your 9Xtreme SD-card, (viewtopic.php?f=7&t=7715).moxieman3864 wrote:i can't figure out the voice thing either
To setup voices go to your: Model Setup / Voice / Voice Alarms to add your voices .
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Receive 9xtreme and Installation
The manual linked above explains very well how to program voice alrams, etc..
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 17
- Joined: Mon Sep 15, 2014 3:13 pm
- Country: -
Re: Receive 9xtreme and Installation
hello mike B.
THANKS FOR TRYING TO HEP I APPRECAITe IT AND everybody else with input i tryed put the USB INTO THE TX i'm getting tones on the computer but i'm only getting on the screen it says 9xtreme and at the bottom left it reads r00.3 and when i go into eepske-eeprom and try to read memory from tx it reads tx disk not mounted the only way for me to get into that is to do the bootloader mode every time any suggestions ?
THANKS FOR TRYING TO HEP I APPRECAITe IT AND everybody else with input i tryed put the USB INTO THE TX i'm getting tones on the computer but i'm only getting on the screen it says 9xtreme and at the bottom left it reads r00.3 and when i go into eepske-eeprom and try to read memory from tx it reads tx disk not mounted the only way for me to get into that is to do the bootloader mode every time any suggestions ?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Receive 9xtreme and Installation
To get the two drives appearing on the computer you need to start the radio in "bootloader" mode. You may have been doing this, but the method is to hold both horizontal trims towards the centre, then power the radio on.
The radio should then start and show "Boot Loader V1.7Ready", and maybe "No Firmware" underneath.
Now plug the USB cable in to the computer, the two drives should now appear.
Is this what you have been doing?
Mike.
The radio should then start and show "Boot Loader V1.7Ready", and maybe "No Firmware" underneath.
Now plug the USB cable in to the computer, the two drives should now appear.
Is this what you have been doing?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Receive 9xtreme and Installation
Hi moxieman3864,
Should look like this: Bob B.
Should look like this: Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Receive 9xtreme and Installation
Mike
For step by step guidance on flashing and upgrading firmware etc on the 9Xtreme, can we follow exactly the instructions in the 9XR PRO document titled 'Communicating with Computer' (attached) ?
regards
Hans
For step by step guidance on flashing and upgrading firmware etc on the 9Xtreme, can we follow exactly the instructions in the 9XR PRO document titled 'Communicating with Computer' (attached) ?
regards
Hans
- Attachments
-
- 9XR Pro Communicating with computer 2014-04-25.pdf
- (450.06 KiB) Downloaded 284 times
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Receive 9xtreme and Installation
Yes, that pretty much describes the operation.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Receive 9xtreme and Installation
Thanks Mike
I cant believe the great support you provide!!
regards
Hans
I cant believe the great support you provide!!
regards
Hans
-
- Posts: 17
- Joined: Mon Sep 15, 2014 3:13 pm
- Country: -
Re: Receive 9xtreme and Installation
ok got it. top picture loads just like that one the bottom picture dose not. i have to go into my file explorer a click on disk drive E and my sd card is there with Voice Pack for Ersky9x16Khz i guess it 's the same thing just about. any how thanks and i was just wondering every time i use the usb eepesky i have to put the tx in bootloader mode ? thanks
-
- Posts: 17
- Joined: Mon Sep 15, 2014 3:13 pm
- Country: -
Re: Receive 9xtreme and Installation
ok got it. top picture loads just like that one the bottom picture dose not. i have to go into my file explorer a click on disk drive E and my sd card is there with Voice Pack for Ersky9x16Khz i guess it 's the same thing just about. any how thanks and i was just wondering every time i use the usb eepesky i have to put the tx in bootloader mode ? thanks
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Receive 9xtreme and Installation
Yes, if you want to use eepskye, you need to be in bootloader mode.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Receive 9xtreme and Installation
I'm just wondering how to get the message "No Firmware" to go away when you go into boot-loader mode.
What is the name of the file and where do you put it?
What is the name of the file and where do you put it?
Re: Receive 9xtreme and Installation
Download the latest 9XT firmware file, create a folder called "firmware" on your SD Card root directory if it's not already there, and copy the firmware file to the folder.
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Receive 9xtreme and Installation
When you run the bootloader it lists all the .bin files found in the "FIRMWARE" (no 'S'') directory. If there are no files, then it displays "No Firmware".
If you put a .bin file (or several) in the "FIRMWARE" directory, then its (their) name(s) will be displayed rather than "No Firmware".
Mike.
If you put a .bin file (or several) in the "FIRMWARE" directory, then its (their) name(s) will be displayed rather than "No Firmware".
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Receive 9xtreme and Installation
Mike, maybe "No Firmware" should be renamed as it is causing confusion? Maybe no firmware on the SD Card, or maybe No Backup Firmware, or something similar.
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Receive 9xtreme and Installation
Hi Mike
I'm just trying out the firmware update process at the moment -
I checked the version of the firmware on the 9Xtreme - it was V1946 26/8/15 r218
I downloaded the ersky9x9XT_rom.bin file from the homepage on to the SD card using the USB connection and then flashed it to the TX using bootloader
Everything worked ok and it said flash complete
I checked the version again on the TX - it was the same version, ie V1946 26/8/15 r218 !
Is this correct or is the flash process not working properly ?
I understood from prevoius posts that there is a new firmware version dated 21 Oct ?
any thoughts
regards
Hans
I'm just trying out the firmware update process at the moment -
I checked the version of the firmware on the 9Xtreme - it was V1946 26/8/15 r218
I downloaded the ersky9x9XT_rom.bin file from the homepage on to the SD card using the USB connection and then flashed it to the TX using bootloader
Everything worked ok and it said flash complete
I checked the version again on the TX - it was the same version, ie V1946 26/8/15 r218 !
Is this correct or is the flash process not working properly ?
I understood from prevoius posts that there is a new firmware version dated 21 Oct ?
any thoughts
regards
Hans
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Receive 9xtreme and Installation
It's here: viewtopic.php?f=7&t=4676#p65894 in ersky9xProvR218g.zip.
I haven't done a formal release (yet).
There is a later version also there from 1-Nov-2015 called ersky9x9XT_romFixEXTn.zip.
This fixes the problems with the EXT signal selection for fitting more 3-position switches.
Mike.
I haven't done a formal release (yet).
There is a later version also there from 1-Nov-2015 called ersky9x9XT_romFixEXTn.zip.
This fixes the problems with the EXT signal selection for fitting more 3-position switches.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Receive 9xtreme and Installation
Mike
Thanks for the link to the firmware test versions - I will keep track on that
I have now successfully updated the firmware using version dated 21 October that you posted earlier - so that proves that its all working as expected
Just one other question - when in bootloader mode, it sometimes can take a minute or so before the text comes on to the screen - is this normal?
regards
Hans
Thanks for the link to the firmware test versions - I will keep track on that
I have now successfully updated the firmware using version dated 21 October that you posted earlier - so that proves that its all working as expected
Just one other question - when in bootloader mode, it sometimes can take a minute or so before the text comes on to the screen - is this normal?
regards
Hans
Re: Receive 9xtreme and Installation
Ok, I can't find a 2.3mm drill bit anywhere.. ideas? Would a 2mm drill also do it? I don't want to damage the plastic, but I also don't want to open the holes to much with a thicker drill bit
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Receive 9xtreme and Installation
No, you should see "9XTREME" in the centre almost immediately (this comes from the original mainboard, followed by the "Boot Loader" screen within a second or so.lancaster wrote:Just one other question - when in bootloader mode, it sometimes can take a minute or so before the text comes on to the screen - is this normal?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Receive 9xtreme and Installation
I live in Canada, where we're supposed to be metric but all our construction tools, materials, etc are 'American'. So I wouldn't be able to find it either. I don't know how common M2.3 is, but it certainly is available online so I didn't think it was abnormal. I used a 3/32". I don't think it is THAT critical. The screws are M2.5 so make sure the drill is smaller than that. If M2.3 isn't available, is M2.4? 2.2?jhsa wrote:Ok, I can't find a 2.3mm drill bit anywhere.. ideas? Would a 2mm drill also do it? I don't want to damage the plastic, but I also don't want to open the holes to much with a thicker drill bit
João
Re: Receive 9xtreme and Installation
No. I could only find 2mm locally..
Will have to try a 2mm and try to open the hole a bit more. Fingers crossed. if it goes wrong I can always remove the pins and solder wires and plugs..
João
Will have to try a 2mm and try to open the hole a bit more. Fingers crossed. if it goes wrong I can always remove the pins and solder wires and plugs..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Receive 9xtreme and Installation
Well, when I first realized they screwed up with the screws... as a test I cranked the screws into mine without boring the hole out at all. Yes it damaged the posts... no, it didn't matter at all. It holds perfectly well. You can even take the screws out and put in the original smaller ones and it still grips. Plastic is flexible.
Re: Receive 9xtreme and Installation
I will see if I have some longer thinner screws here. Maybe some from micro servos, I don't know.
I will solder headers to all the numbered pads also. That will make it easier to connect stuff I guess.
João
I will solder headers to all the numbered pads also. That will make it easier to connect stuff I guess.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Receive 9xtreme and Installation
Drill bit. I just pressed my screws against my drill bit kit and picked one that was larger that the screw body but smaller diameter than the threads. Just undersized. I live in a SAE measurement world so I apply the calibrated eyeball tool.
I also used a finger chuck and wiggled it a little. In the past if I made a hole too large, I'd fill it with ca and re drill it.
When I have split a post I have several fixes.
One is to see if a brass tubing sleeve can be put over it. Sometimes I luck out with the diameter. Then fill with CA and re drill.
Another is to wrap thread or thin string around the split post the total length. Then apply CA to the string. It reinforces the post for use again.
I've even gathered up the shattered pieces to reconstruct the post with ca before wrapping and re drilling it.
Use a toothpick to apply CA or kicker. It's easier to control the amount and where the liquid goes in tight places.
Time and wine on my side I guess[emoji3][emoji485]
I also used a finger chuck and wiggled it a little. In the past if I made a hole too large, I'd fill it with ca and re drill it.
When I have split a post I have several fixes.
One is to see if a brass tubing sleeve can be put over it. Sometimes I luck out with the diameter. Then fill with CA and re drill.
Another is to wrap thread or thin string around the split post the total length. Then apply CA to the string. It reinforces the post for use again.
I've even gathered up the shattered pieces to reconstruct the post with ca before wrapping and re drilling it.
Use a toothpick to apply CA or kicker. It's easier to control the amount and where the liquid goes in tight places.
Time and wine on my side I guess[emoji3][emoji485]
Re: Receive 9xtreme and Installation
Thanks Showmaster.. Good tips
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Receive 9xtreme and Installation
Strip the hole with the original screw, that should give enough room for the new screws.
Re: Receive 9xtreme and Installation
Hi MikeMikeB wrote:No, you should see "9XTREME" in the centre almost immediately (this comes from the original mainboard, followed by the "Boot Loader" screen within a second or so.lancaster wrote:Just one other question - when in bootloader mode, it sometimes can take a minute or so before the text comes on to the screen - is this normal?
Mike.
The bootloader screen seems to take time to settle in - it flashes a couple of times before becoming permanently on and then works fine.
Also I dont get the '9XTREME' message
Will this jeopardise the transfer process at some point and do I need to take any action to prempt a problem?
regards
Hans
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Receive 9xtreme and Installation
Hi João,
For the Thread Tap size: M2.5 x 0.45, use Tap Drill Size: 2.00 mm.
See chart: (http://www.industrialhardware.com/skin1 ... Sizes.html)
(http://www.banggood.com/10Pcs-Micro-HSS ... 24567.html)
It is risky and I should not do it, but I just pushed very hard on the black screws and cranked them in.
I do not recommend it however.
Bob B.
For the Thread Tap size: M2.5 x 0.45, use Tap Drill Size: 2.00 mm.
See chart: (http://www.industrialhardware.com/skin1 ... Sizes.html)
(http://www.banggood.com/10Pcs-Micro-HSS ... 24567.html)
It is risky and I should not do it, but I just pushed very hard on the black screws and cranked them in.
I do not recommend it however.
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).