The Module

Post Reply
User avatar
MikeB
9x Developer
Posts: 17772
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

The Module

Post by MikeB » Fri Jul 03, 2015 11:42 am

The DSM telemetry module, that uses the internal antenna of the 9XR-PRO, is now available, see: http://www.hobbyking.com/hobbyking/stor ... ible_.html.

This is fully supported by ersky9x as installed on the 'PRO as delivered.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!


User avatar
OctavioS
Posts: 631
Joined: Sun Aug 17, 2014 11:54 pm
Country: Portugal
Location: Madeira

Re: The Module

Post by OctavioS » Tue Jun 07, 2022 7:29 pm

Here is the updated link.
Is there any specific reason i cannot bind this module to the receivers below?
What happens is that, during the binding procedure, the light blinks fast, and then it slows, as if it was binding, but the light goes off and not solid. it simply wont bind.
I get a solid light with this module, but no movement.
The channel order is TAER.
Image
Attachments
IMG_20220607_201359146~2.jpg
(779.82 KiB) Not downloaded yet
Last edited by OctavioS on Sat Jul 02, 2022 12:05 am, edited 1 time in total.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.

User avatar
OctavioS
Posts: 631
Joined: Sun Aug 17, 2014 11:54 pm
Country: Portugal
Location: Madeira

Re: The Module

Post by OctavioS » Tue Jun 07, 2022 9:11 pm

With these receivers and the 9xr pro with the orangerx module (9xr pro exclusive module) everything works fine.
With the same settings and the above receivers, nothing.
Attachments
Sem Título.png
(871.06 KiB) Not downloaded yet
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.

User avatar
OctavioS
Posts: 631
Joined: Sun Aug 17, 2014 11:54 pm
Country: Portugal
Location: Madeira

Re: The Module

Post by OctavioS » Tue Jun 07, 2022 10:20 pm

[SOLVED] The only reason for the receivers not binding was the fact the telemetry com port 1 was not inverted. I just inverted com port 1 and everything went fine. Even for the receivers that do not support telemetry, like the ones above, you need to invert that com port in the model telemetry menu.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.

User avatar
MikeB
9x Developer
Posts: 17772
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: The Module

Post by MikeB » Wed Jun 08, 2022 6:42 pm

During bind, the Rx sends back to the Tx what bind mode it accepts. The Tx module passes this, using the telemetry connection, on so the radio then knows when the bind has completed, and also then keeps the bind mode so it is correct after a power cycle.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!


User avatar
OctavioS
Posts: 631
Joined: Sun Aug 17, 2014 11:54 pm
Country: Portugal
Location: Madeira

Re: The Module

Post by OctavioS » Fri Jun 10, 2022 12:41 am

Thx Mike. I would never guess that a receiver still uses telemetry com port for binding, even though it doesn't support telemetry. Now I know.
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.


Post Reply

Return to “Orange DSM Telemetry module”