Elevator and Rudder trims reversed.
Elevator and Rudder trims reversed.
My elevator and rudder trims are backwards. I have a mode 2 9xr pro. I've downloaded the latest firmware from eePskye and flashed it to the radio. The version on the radio says ersky9x-r204. On screen 1 of the Radio Setup, none of the mode options are inverted, and when I invert them all it doesn't fix the problem anyway. The oddest thing is that I can still get into boot loader mode by pressing both the rudder and aileron trim to the inside when turning it on, you'd think that wouldn't work since my rudder trim is backwards. So any ideas what the problem is?
Re: Elevator and Rudder trims reversed.
You might have inverted the stick direction by mistake. Can you post a picture here of the screen you changed the mode?
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Elevator and Rudder trims reversed.
Just realized that I have reversed trims on rudder and elevator on my mode 2 9XR Pro. Version is r213 date 10.10.2014.
I had been using this TX until Christmas on a September version of firmware with no problem. Then updated to this one, the latest at the time.
Switching to mode 1 leaves the problem on the same physical trim buttons. Now it's throttle and rudder. Sticks are NOT reversed. My other 9XR Pro is running latest r214 and is normal.
EDIT: Got it. I had inadvertently loaded ersky9x instead of ersky9xR. Tried two versions of the XR version. Both worked, so all is well again.
What is the difference, anyway. Everything on the 9XR Pro seemed to work normally except trims when I had the X version installed.
I had been using this TX until Christmas on a September version of firmware with no problem. Then updated to this one, the latest at the time.
Switching to mode 1 leaves the problem on the same physical trim buttons. Now it's throttle and rudder. Sticks are NOT reversed. My other 9XR Pro is running latest r214 and is normal.
EDIT: Got it. I had inadvertently loaded ersky9x instead of ersky9xR. Tried two versions of the XR version. Both worked, so all is well again.
What is the difference, anyway. Everything on the 9XR Pro seemed to work normally except trims when I had the X version installed.
Last edited by Daedalus66 on Sat Jan 31, 2015 8:34 pm, edited 1 time in total.
Re: Elevator and Rudder trims reversed.
Ah that was it thanks, downloaded this version and it's back to normal.
https://ersky9x.googlecode.com/svn/trun ... xr_rom.bin
https://ersky9x.googlecode.com/svn/trun ... xr_rom.bin
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: Elevator and Rudder trims reversed.
So that's two of us happy.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Elevator and Rudder trims reversed.
Two of the sticks on the 'PRO are wired reversed compared to the SKY board.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Elevator and Rudder trims reversed.
Ahhh, that explains it
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW