Page 1 of 1
Assign ID to exponential travel profiles
Posted: Sun Aug 12, 2018 12:29 am
by iFeghali
Hello
Is there a way to assign the 3 position switch “ID” to exponential travel profiles in the following way:
ID- > LOW
ID > MID
ID+ > HIGH
?
Enviado do meu iPhone usando Tapatalk
Re: Assign ID to exponential travel profiles
Posted: Sun Aug 12, 2018 12:51 am
by jhsa
You mean something like a triple rate but with Expo only?
João?
Re: Assign ID to exponential travel profiles
Posted: Sun Aug 12, 2018 1:39 am
by iFeghali
jhsa wrote:You mean something like a triple rate but with Expo only?
João?
Nope. I know I can set set 3 profiles for EXPO for each channel. So I can have a LOW EXPO, MID EXPO and HIGH EXPO for each channel. I can then assign TWO buttons to switch between those 3 profiles. If I use two normal switches they give me 4 different combinations but we have only 3 profiles, so one of them gets repeated and it’s confusing. That’s why I want to use a single 3 position switch which would make a lot more sense for me.
Enviado do meu iPhone usando Tapatalk
Re: Assign ID to exponential travel profiles
Posted: Sun Aug 12, 2018 8:57 am
by MikeB
Set DrSw1 to !ID^ (!ID0) and DrSw2 to IDv (ID2).
With the swith up you get high rate, in the centre you get mid rate and down gives you low rate.
Mike
Re: Assign ID to exponential travel profiles
Posted: Sun Aug 12, 2018 12:30 pm
by jhsa
This is why I asked if he wanted the triple rate. I didn't understand his question
Re: Assign ID to exponential travel profiles
Posted: Mon Aug 13, 2018 1:18 am
by iFeghali
MikeB wrote:Set DrSw1 to !ID^ (!ID0) and DrSw2 to IDv (ID2).
With the swith up you get high rate, in the centre you get mid rate and down gives you low rate.
Mike
That’s the first thing I tried mike, but unfortunately it didn’t work (or I’m doing it wrong). Doing as you said I get MID at the top and HIGH at middle and bottom.
Enviado do meu iPhone usando Tapatalk
Re: Assign ID to exponential travel profiles
Posted: Mon Aug 13, 2018 8:13 am
by MikeB
DrSw1 needs to be !ID^ (that is NOT ID^). When editing the switch value go DOWN to get the NOT switch values.
Mike
Re: Assign ID to exponential travel profiles
Posted: Mon Aug 13, 2018 9:50 am
by iFeghali
MikeB wrote:DrSw1 needs to be !ID^ (that is NOT ID^). When editing the switch value go DOWN to get the NOT switch values.
Mike
Thank you very much. Works like a charm
Enviado do meu iPhone usando Tapatalk
Re: Assign ID to exponential travel profiles
Posted: Mon Aug 13, 2018 10:37 am
by jhsa
Try:
DrSw1 set as !IDv (!ID2)
DrSw2 set as !ID^ (!ID1)
In my opinion it will work better. I have just tried in Eepskye
By the way, triple rates are explained on the Er9x manual, page 42 and 43.
João
Re: Assign ID to exponential travel profiles
Posted: Mon Aug 13, 2018 9:07 pm
by iFeghali
jhsa wrote:Try:
DrSw1 set as !IDv (!ID2)
DrSw2 set as !ID^ (!ID1)
In my opinion it will work better. I have just tried in Eepskye
By the way, triple rates are explained on the Er9x manual, page 42 and 43.
João
Thanks. It’s clear now. For anyone interested that’s the relevant part:
Hi is DrSw1 OFF (DrSw2 doesn't matter)
Mid is DrSw1 ON, DrSw2 OFF
Lo is DrSw1 ON, DrSw2 ON
Enviado do meu iPhone usando Tapatalk