Hello
Is there a way to assign the 3 position switch “ID” to exponential travel profiles in the following way:
ID- > LOW
ID > MID
ID+ > HIGH
?
Enviado do meu iPhone usando Tapatalk
Assign ID to exponential travel profiles
Re: Assign ID to exponential travel profiles
You mean something like a triple rate but with Expo only?
João?
João?
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Assign ID to exponential travel profiles
Nope. I know I can set set 3 profiles for EXPO for each channel. So I can have a LOW EXPO, MID EXPO and HIGH EXPO for each channel. I can then assign TWO buttons to switch between those 3 profiles. If I use two normal switches they give me 4 different combinations but we have only 3 profiles, so one of them gets repeated and it’s confusing. That’s why I want to use a single 3 position switch which would make a lot more sense for me.jhsa wrote:You mean something like a triple rate but with Expo only?
João?
Enviado do meu iPhone usando Tapatalk
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Assign ID to exponential travel profiles
Set DrSw1 to !ID^ (!ID0) and DrSw2 to IDv (ID2).
With the swith up you get high rate, in the centre you get mid rate and down gives you low rate.
Mike
With the swith up you get high rate, in the centre you get mid rate and down gives you low rate.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Assign ID to exponential travel profiles
This is why I asked if he wanted the triple rate. I didn't understand his question
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Assign ID to exponential travel profiles
That’s the first thing I tried mike, but unfortunately it didn’t work (or I’m doing it wrong). Doing as you said I get MID at the top and HIGH at middle and bottom.MikeB wrote:Set DrSw1 to !ID^ (!ID0) and DrSw2 to IDv (ID2).
With the swith up you get high rate, in the centre you get mid rate and down gives you low rate.
Mike
Enviado do meu iPhone usando Tapatalk
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Assign ID to exponential travel profiles
DrSw1 needs to be !ID^ (that is NOT ID^). When editing the switch value go DOWN to get the NOT switch values.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Assign ID to exponential travel profiles
Thank you very much. Works like a charmMikeB wrote:DrSw1 needs to be !ID^ (that is NOT ID^). When editing the switch value go DOWN to get the NOT switch values.
Mike
Enviado do meu iPhone usando Tapatalk
Re: Assign ID to exponential travel profiles
Try:
DrSw1 set as !IDv (!ID2)
DrSw2 set as !ID^ (!ID1)
In my opinion it will work better. I have just tried in Eepskye
By the way, triple rates are explained on the Er9x manual, page 42 and 43.
João
DrSw1 set as !IDv (!ID2)
DrSw2 set as !ID^ (!ID1)
In my opinion it will work better. I have just tried in Eepskye
By the way, triple rates are explained on the Er9x manual, page 42 and 43.
João
- Attachments
-
- ER9x_Manual_2015-v01.pdf
- (2.08 MiB) Downloaded 253 times
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Assign ID to exponential travel profiles
Thanks. It’s clear now. For anyone interested that’s the relevant part:jhsa wrote:Try:
DrSw1 set as !IDv (!ID2)
DrSw2 set as !ID^ (!ID1)
In my opinion it will work better. I have just tried in Eepskye
By the way, triple rates are explained on the Er9x manual, page 42 and 43.
João
Hi is DrSw1 OFF (DrSw2 doesn't matter)
Mid is DrSw1 ON, DrSw2 OFF
Lo is DrSw1 ON, DrSw2 ON
Enviado do meu iPhone usando Tapatalk