Page 1 of 1
How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Fri May 27, 2016 8:18 pm
by pyr8
I have a XJT bound to a XSR with my 9XR Pro...no issues binding.
With my old TX/RX combo (Orange LRS), when the radio TX was on and lost signal with the RX, the TX module would give a warning tone...same when the RX/TX were about to go out of range of each other.
How do I setup the 9XR Pro and XJT combo to give the same audible feedback when the RX is getting to far out of TX range?
Thanks in advance folks!
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Fri May 27, 2016 9:15 pm
by MikeB
You should get a voice warning from openTx when the RSSI values drops low.
Mike.
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Fri May 27, 2016 9:41 pm
by pyr8
MikeB wrote:You should get a voice warning from openTx when the RSSI values drops low.
Mike.
What about when the RX is completely un-powered or out of range...and...is the extent of the signal strenght warnings voice, or can I have the radio beep as well like with the "Orange LRS"?
Thanks Mike!
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Sat May 28, 2016 2:16 pm
by Kilrah
You would get one "telemetry lost" warning when going out of range/unpowered before further warnings are suppressed.
Beeps/voice can be set any way you like using logical switches and special functions.
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Sun May 29, 2016 7:10 pm
by pyr8
Is there a decent write-up or video on how to set voice triggers on the 9XR Pro running OpenTX?
I want to trigger a voice file on low battery and RSSI from FrSky Telemetry.
I watched João video here:
https://www.youtube.com/watch?v=6WRosEf ... qcuIqJXhb9 , But the options he describes are not available to me on the 9XR Pro with OpenTx?!
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Sun May 29, 2016 7:15 pm
by Kilrah
Set up a logcial switch with your condition, then use that to trigger a "play track" special function.
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Sun May 29, 2016 7:29 pm
by pyr8
Kilrah wrote:Set up a logcial switch with your condition, then use that to trigger a "play track" special function.
Ah ha...that's what I was looking for!
Now what should the "FUNC" Setting be in "Logical Switches"? Is there a list of the meanings of the different options?
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Sun May 29, 2016 9:14 pm
by pyr8
pyr8 wrote:Kilrah wrote:Set up a logcial switch with your condition, then use that to trigger a "play track" special function.
Ah ha...that's what I was looking for!
Now what should the "FUNC" Setting be in "Logical Switches"? Is there a list of the meanings of the different options?
Found my answer here:
http://open-txu.org/home/continuing-edu ... functions/
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Tue Jul 12, 2016 4:40 pm
by Geofrancis
what version of opentx are you using to get telemetry with xjt? as far as i knew it only worked with er9x.
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Tue Jul 12, 2016 11:26 pm
by pyr8
Geofrancis wrote:what version of opentx are you using to get telemetry with xjt? as far as i knew it only worked with er9x.
Whatever the latest release is!
Re: How do I setup FrSky XJT with 9XR Pro Running OpenTx?
Posted: Tue Jul 12, 2016 11:27 pm
by pyr8
OpenTX 2.1.8 (2016-04-14)