Left side gimbal has on response
Left side gimbal has on response
After powering up for the first time ever and bound to a RX with 4 servos in the main outputs (ail thr rud ele) the rhs gimbal responded as normal but the lhs had no input to the servos at all.
This does not have any warranty so I cannot send it back.
This does not have any warranty so I cannot send it back.
Re: Left side gimbal has on response
After turning the radio ON press UP or DOWN to go to a screen that has 2 squares with little circles inside. Do the circles move when you move the sticks? Do they center when you center the sticks?
If so proceed to a screen that show some bars moving horizontally when you move the sticks.
Do the first 4 bars move when you move both sticks on all directions?
João
If so proceed to a screen that show some bars moving horizontally when you move the sticks.
Do the first 4 bars move when you move both sticks on all directions?
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Left side gimbal has on response
Hi Joao
I get the 2 squares and the sticks show movement in both boxes
When I move to the screen with the bars, There is 3 bars on the Lhs of scrn and 1 at the top of the Rhs side.
I am using Mode 1 so the Thro and Ail move the Lhs 2 bars at top but the Lhs stick has no effect on the other 2 bars
The Ail, Thro, Rud and Ele trim switches all work OK
Thanks Geoff
I get the 2 squares and the sticks show movement in both boxes
When I move to the screen with the bars, There is 3 bars on the Lhs of scrn and 1 at the top of the Rhs side.
I am using Mode 1 so the Thro and Ail move the Lhs 2 bars at top but the Lhs stick has no effect on the other 2 bars
The Ail, Thro, Rud and Ele trim switches all work OK
Thanks Geoff
Re: Left side gimbal has on response
What firmware do you have installed?
go to the mixer menu, and tell us what you have there for Ch1 to Ch4. Or if you can take a picture and post it here..
João
go to the mixer menu, and tell us what you have there for Ch1 to Ch4. Or if you can take a picture and post it here..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Left side gimbal has on response
I will be out of action (both wrists operated on) for a couple of days so I will get back to you when I can
Thanks a bunch Geoff
Thanks a bunch Geoff
Re: Left side gimbal has on response
Hi I'm back with both wrists strapped up but thankley I can use my fingers
The F/W is FrSky9X.
The original F/W had the same problem hence the re-flash
I hope all is well in Germany
Cheers Geoff
The F/W is FrSky9X.
The original F/W had the same problem hence the re-flash
I hope all is well in Germany
Cheers Geoff
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Left side gimbal has on response
As João asked, next:
"go to the mixer menu, and tell us what you have there for Ch1 to Ch4."
Since the telltales move in the boxes, your sticks are working correctly, so this is very likely just a setting or two that is not correct.
The stock firmware is an earlier version of ersky9x.
Mike.
"go to the mixer menu, and tell us what you have there for Ch1 to Ch4."
Since the telltales move in the boxes, your sticks are working correctly, so this is very likely just a setting or two that is not correct.
The stock firmware is an earlier version of ersky9x.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Left side gimbal has on response
Glad all went well and you can still write
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Left side gimbal has on response
In the mix scrn ch1 99 thr, ch2 100 ail, ch3 100 ele R--100 half thr, ch4 100 rudMikeB wrote:As João asked, next:
"go to the mixer menu, and tell us what you have there for Ch1 to Ch4."
Since the telltales move in the boxes, your sticks are working correctly, so this is very likely just a setting or two that is not correct.
The stock firmware is an earlier version of ersky9x.
Mike.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Left side gimbal has on response
Is this added mix (R--100 half thr) maybe what is causing the problem ?Stuka wrote:In the mix scrn ch1 99 thr, ch2 100 ail, ch3 100 ele R--100 half thr, ch4 100 rud
Maybe try removing it and see what happens.
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Left side gimbal has on response
Please go to the Model Select Menu, select an empty slot, and then create a new model.. see if all moves correctly now. The new model will create a model with default mixes..
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Left side gimbal has on response
hi jhsa I tried a new model and all seems to be operating ok
I will be able to test more memories and different mixes later so hopefully I wont end up with a fancy boat anchor
Cheers
I will be able to test more memories and different mixes later so hopefully I wont end up with a fancy boat anchor
Cheers
Re: Left side gimbal has on response
I think you found your problem
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW