Castle ICE 50 Throttle calibration and curves with Turnigy 9
Posted: Wed Nov 19, 2014 1:23 pm
Hello to all,
Guys I have just received Turnigy 9XR PRO but still confuses me to several points.
1) I want to make the throttle calibration to my CC Phoenix ICE 50.
This TX doesn't have endpoint menu so I think I should do through limits menu (please correct me if I am wrong).
To all videos for CC throttle calibration, are demonstrate the end points to be from +50 for both higher and lower stick position and start rising up to the point that will hear the calibration beep sound.
To my TX the values in curves are from -100 to +100 and I put a linear throttle curve (-100,-50,0,50,100) for throttle calibration. Since in the limit menu the values are from -100 to +100 I set CH3 limits to -50 and 50. I fire the heli with stick to full throttle. Start raising up to sound (+78 and add 2 more = +80) and then do the same by lowering the stick for lower (-68 and add -2 more = -70). A strange thing though is that after high stick calibration beep confirmation, after 3-4 secs it makes the same "beep confirmation" even if I don't react anyway with the stick. When I finally reach the lower end point it does again the "beep confirmation".
The process seems to be completed correctly (because it works!!) but if I do the same procedure, the numbers of the limits will beep to different position (2-3 number lower or higher from previous). Is this normal? Is something wrong with my limits (plus, minus) because an all videos the endpoints are always set to plus values!!!
2) I want to put the correct throttle curves because I need to run the esc in governor-set RPM mode.
I when I change to governor set RPM, I place 2800, 2950, 3060 which advice me to put 30%, 70%, 100% flat throttle curve. Since my throttle curves are from -100 to + 100 (and the scale is not from 0 to 100) I have placed for 30% 0,-40,-40,-40,-40 (the first 0 is for soft start and stop) for 70% 35,35,35,35,35 and for 100% 100,100,100,100,100. Am I correct?
Any kind advice?
Guys I have just received Turnigy 9XR PRO but still confuses me to several points.
1) I want to make the throttle calibration to my CC Phoenix ICE 50.
This TX doesn't have endpoint menu so I think I should do through limits menu (please correct me if I am wrong).
To all videos for CC throttle calibration, are demonstrate the end points to be from +50 for both higher and lower stick position and start rising up to the point that will hear the calibration beep sound.
To my TX the values in curves are from -100 to +100 and I put a linear throttle curve (-100,-50,0,50,100) for throttle calibration. Since in the limit menu the values are from -100 to +100 I set CH3 limits to -50 and 50. I fire the heli with stick to full throttle. Start raising up to sound (+78 and add 2 more = +80) and then do the same by lowering the stick for lower (-68 and add -2 more = -70). A strange thing though is that after high stick calibration beep confirmation, after 3-4 secs it makes the same "beep confirmation" even if I don't react anyway with the stick. When I finally reach the lower end point it does again the "beep confirmation".
The process seems to be completed correctly (because it works!!) but if I do the same procedure, the numbers of the limits will beep to different position (2-3 number lower or higher from previous). Is this normal? Is something wrong with my limits (plus, minus) because an all videos the endpoints are always set to plus values!!!
2) I want to put the correct throttle curves because I need to run the esc in governor-set RPM mode.
I when I change to governor set RPM, I place 2800, 2950, 3060 which advice me to put 30%, 70%, 100% flat throttle curve. Since my throttle curves are from -100 to + 100 (and the scale is not from 0 to 100) I have placed for 30% 0,-40,-40,-40,-40 (the first 0 is for soft start and stop) for 70% 35,35,35,35,35 and for 100% 100,100,100,100,100. Am I correct?
Any kind advice?