I dont have sound.

Everything about the smartie programmer and backlight kit!
Post Reply
Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

I dont have sound.

Post by Rad » Fri Jun 24, 2016 9:01 am

Hi! I have just installed the 9xtreme in my flysky th9xb radio, I have also updated the firmware to the last version (Rev218 for the 9xtreme)
After that I donwloaded the sound files from there and I put them in the SD card and got no sound, and also tried other link from somewhere here in the forum but still got no sound.

Any tip out there?

Thanks!
https://radindustries.wordpress.com/


User avatar
jhsa
Posts: 19393
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: I dont have sound.

Post by jhsa » Fri Jun 24, 2016 10:16 am

Downloaded the files from there? Where? Er9x.com?
How did you put them on the SD Card?
Please make sure there is a folder called "voice".
Inside this folder you should find 3 other folders. "System, user and modelNames".

Does your radio beep when you move the trims?

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
bob195558
Posts: 2253
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: I dont have sound.

Post by bob195558 » Fri Jun 24, 2016 10:45 am

Also see here for more info: Directory of information to help with installing the 9Xtreme Board
and with using erSky9x and eepSkye:
(viewtopic.php?f=95&t=7182).
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 11:29 am

Yes, I have downloaded the audio pack from er9x.com and I think I put the files in the sd card as you said. And I dont have trimmer sounds neither...

Anyway I will try to do it again as soon as I arrive home in a couple of hours, and see what happens. Thanks!
https://radindustries.wordpress.com/

User avatar
jhsa
Posts: 19393
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: I dont have sound.

Post by jhsa » Fri Jun 24, 2016 12:34 pm

Please check first if the radio beeps. Just move the trim switches.. that will tell us if you have sound at all..
Also, in radio setup/audioHaptic there is a volume setting.

In Model Setup/General you can assign a pot to control the volume. Please check if there is a pot assigned and is at minimum. That would turn the volume completely down..

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW


Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 2:49 pm

Well, Im back at home.

The radio does not beep, I move the 4 trim switches and it does not make any sound.

In radio, audio haptic I have
Volume 23 (That is the maximum)
Beeper Norm
Beep countdown OFF
Minute beep OFF
SPeaker pitch 100
Haptic Strength 5
Haptic Min Run 40

Also I took a look to model setup and I saw there was a pot for the sounds. I played with it and still got no sound.



About the SD Card, I also download the sound pack from this link: viewtopic.php?f=7&t=7715
And I put the files as you told me.

Any clue?
https://radindustries.wordpress.com/

User avatar
jhsa
Posts: 19393
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: I dont have sound.

Post by jhsa » Fri Jun 24, 2016 4:22 pm

Yes, that is the pack to be used..

You need to check your speaker is well connected and working.
Don't you hear absolutely no noise from the speaker, not even a buzzing sound?

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 4:24 pm

Speaker is well conected but I dont heard anything. Anyway I found a thread here in the forum with some clues, and the guy that was having problems fixed it formating the SD Card to fat32. Im doing that right now and we will see what happens.

The Computer recognises the SD Card when in bootloader mode, and also the Radio says the card is ready...
https://radindustries.wordpress.com/

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 4:43 pm

Ok back. SD Card formated to FAT32 with the slow format, files back in the SD Card and still no welcome or trim sounds...

The SD Card is detected in bootloader mode and in the normal mode it says is still present and ready.
https://radindustries.wordpress.com/

User avatar
Kilrah
Posts: 10739
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: I dont have sound.

Post by Kilrah » Fri Jun 24, 2016 4:46 pm

The question about the trim sounds was because they do not require the SD card. So if you have no trim beeps it is pointless to try playing with the card, if the settings are correct your issue comes from the hardware (speaker badly connected, speaker or board defective).

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 4:49 pm

Another quick update, I tried with the SD Card from my 9XR PRO and still does not work.
https://radindustries.wordpress.com/

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 4:50 pm

Kilrah wrote:The question about the trim sounds was because they do not require the SD card. So if you have no trim beeps it is pointless to try playing with the card, if the settings are correct your issue comes from the hardware (speaker badly connected, speaker or board defective).
I see.. The radio is brand new, just bought it couple of weeks ago and I did not use it because I did not want to mess with the crappy stock software...

But it beeped everytime I pressed a button.
https://radindustries.wordpress.com/

User avatar
Kilrah
Posts: 10739
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: I dont have sound.

Post by Kilrah » Fri Jun 24, 2016 4:52 pm

The 9Xtreme does not use the radio's stock beeper but the speaker that comes bundled with it and needs to be installed/connected.

User avatar
jhsa
Posts: 19393
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: I dont have sound.

Post by jhsa » Fri Jun 24, 2016 4:57 pm

So, a new question, and an old question.

Did you install the speaker that comes with the 9xtreme?

If so, do you hear any buzzing sound when you turn the radio ON and your ear is close to the speaker?

Please post a picture of your board and speaker installation.

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 5:04 pm

When I said I did not heard anythink, I mean I did not heard that buzz too, but hey, I think I found the problem... I checked the speaker conector 10.000 thousand times, but not the speaker itself... Then I saw this:

Image
The positive is not connected and the speaker's board seems to be broken.

Image

I installed everything with extreme caution, so I dont think I broke it, but well, it might be my fault. Do you think I can fix it myself or do I need to buy another speaker? Tips welcome.

This is the board by the way:

Image
https://radindustries.wordpress.com/

User avatar
jhsa
Posts: 19393
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: I dont have sound.

Post by jhsa » Fri Jun 24, 2016 5:41 pm

Ok. i thought it would be something like that :) Good that you found it..
I am not sure you can repair it. Depends if the thin wire that comes from the coil is also broken. Can't really see it.
Maybe you can contact Steven, but those speakers are so cheap..

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Fri Jun 24, 2016 6:16 pm

Im going to write to Steve, maybe he knows how to fix it.

Thanks to everybody, Im going to click in the thanks button of all of you :D
https://radindustries.wordpress.com/

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Sun Jun 26, 2016 3:31 pm

Update: I wrote Steven about how to fix it, but we saw that it was broken beyond repair, so he is going to send me a spare one.

Excelent technical support. :)
https://radindustries.wordpress.com/

Rad
Posts: 386
Joined: Wed Apr 20, 2016 3:43 pm
Country: Austria
Contact:

Re: I dont have sound.

Post by Rad » Mon Jul 04, 2016 8:26 am

Well, I have received the speaker so I installed it and WORKS!

Again, thanks to everybody around here for your help, and thanks to Steve for the technical support. :)
https://radindustries.wordpress.com/


Post Reply

Return to “SMARTIEPARTS PROGRAMMER”