Setting Burn-o-mat

Everything about the smartie programmer and backlight kit!
Post Reply
User avatar
Crashj007
Posts: 133
Joined: Tue Jan 31, 2012 11:44 pm
Country: -
Location: Raleigh, NC, USA
Contact:

Setting Burn-o-mat

Post by Crashj007 » Fri Mar 02, 2012 11:26 pm

This is so simple, I'm embarrassed to ask. I have the Smartie board loaded and I think all your cautions worked It seems to be communicating but I get the following error message:

C:\Program Files (x86)\eePe\avrdude.exe -C C:\Program Files (x86)\eePe\avrdude.conf -p m128 -P usb -c usbasp -U flash:w:C:\Users\Hardie\Downloads\Radio Control\er9x.hex:a
avrdude.exe: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude.exe: Device signature = 0x1e9602
avrdude.exe: Expected signature for ATMEGA128 is 1E 97 02
Double check chip, or use -F to override this check.
avrdude.exe done. Thank you.

I have the port set to usb and the programmer selected as:
usbasp (http://www.fischl.de/usbasp/)
Should I be selecting some other programmer?
Isn't the radio processor Atmel AtMega64 8-bit MCU?
--
FS-TH9X 2.4GHz 9CH from Nitroplanes
Smartieparts board & backlight
Stock Flysky RF and mainboard
er9x FW V 744


User avatar
erazz
9x Developer
Posts: 682
Joined: Tue Dec 27, 2011 6:25 pm
Country: -
Location: NJ-USA
Contact:

Re: Setting Burn-o-mat

Post by erazz » Fri Mar 02, 2012 11:30 pm

Under Burn->config change the mcu type to m64
Z

BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!

User avatar
Crashj007
Posts: 133
Joined: Tue Jan 31, 2012 11:44 pm
Country: -
Location: Raleigh, NC, USA
Contact:

Re: Setting Burn-o-mat

Post by Crashj007 » Sat Mar 03, 2012 12:12 am

Awesome, perfecto, it worked, we have lights and everything.
"My mother thanks you, my father thanks you, and I'd like to thank the members of the academy"
--
FS-TH9X 2.4GHz 9CH from Nitroplanes
Smartieparts board & backlight
Stock Flysky RF and mainboard
er9x FW V 744

User avatar
Westy
Posts: 248
Joined: Tue Jan 31, 2012 8:44 pm
Country: -
Location: Te Awamutu, Waikato, New Zealand
Contact:

Re: Setting Burn-o-mat

Post by Westy » Sat Mar 03, 2012 5:53 am

lol ... .way to to go!!!!

User avatar
erazz
9x Developer
Posts: 682
Joined: Tue Dec 27, 2011 6:25 pm
Country: -
Location: NJ-USA
Contact:

Re: Setting Burn-o-mat

Post by erazz » Sat Mar 03, 2012 1:23 pm

:)


If only all problems were like this....
Z

BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!


User avatar
Westy
Posts: 248
Joined: Tue Jan 31, 2012 8:44 pm
Country: -
Location: Te Awamutu, Waikato, New Zealand
Contact:

Re: Setting Burn-o-mat

Post by Westy » Sat Mar 03, 2012 6:36 pm

he he .... you know it!


Post Reply

Return to “SMARTIEPARTS PROGRAMMER”