Page 1 of 2
Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 12:28 pm
by matzeeg3
Hi I flashed my 9x with opentx 2.2 after that if I turn on the transmitter nothing happens. If I now try to read I get a communication error what do I wrong?
Somebody here how can help me?
Thanks.
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:02 pm
by s_mack
Please provide the exact error.
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:09 pm
by matzeeg3
I attached 2 pictures
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:19 pm
by ReSt
At least. don't use the -F option, because that probably will brick your radio
Reinhard
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:20 pm
by s_mack
That error, "Target doesn't answer", is covered on
the product page under the FAQ tab... relevant section pasted below:
AVRDUDE Error: Target doesn't answer
This error indicates a problem between the programmer and the 9X. It has nothing to do with the USB connection to the computer. It is generally caused by the following:
- You don't have the 9x powered on. This programmer requires the target (the 9X) to be powered.
- One or more of the spring pins is not making contact. This could be a simple alignment issue, or the screws are too loose. Flux residue or oils from your fingers could prevent a signal, so cleaning the pads and pins with 99%+ alcohol can make the difference. Inspect the pins and pads
- Your 9X is a so-called "V1". See the "My 9X is a V1 (or V2 or V3)?" in the pre-sales section above.
- A defective board.
Unfortunately, there's no simple way to test for a defect other than ruling out the other possibilities, so go over everything three times then please contact us for further assistance.
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:24 pm
by s_mack
ReSt wrote: ↑Thu Dec 07, 2017 4:19 pm
At least. don't use the -F option, because that probably will brick your radio
Reinhard
Generally very good advice. NEVER use the -F option!
However, in this case, it can't cause a problem because a connection to the target doesn't exist
It can't solve the issue either, so NEVER USE IT!
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:30 pm
by jhsa
It could have caused a problem if he used it when flashed the radio the first time. Remember he said that after flashing it went blank and never responded again..
A bricked radio will display the same error. Not saying it is the case here though..
João
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:46 pm
by matzeeg3
I flashed it with the opentx companion don't change any settings. Bevor every thing worked fine after nothing...
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 4:58 pm
by jhsa
What settings do you have in companion?
Exactly what file did you flash?
What chip does your radio have?
João
Re: Blank screen after flashing opentx
Posted: Thu Dec 07, 2017 5:13 pm
by s_mack
Matzeeg3, did you go through the troubleshooting items I posted?
My guess is you didn't have the radio on. Flashing an unpowered target can erase it, but not program it.
Re: Blank screen after flashing opentx
Posted: Fri Dec 08, 2017 8:39 am
by matzeeg3
jhsa wrote: ↑Thu Dec 07, 2017 4:58 pm
What settings do you have in companion?
Exactly what file did you flash?
What chip does your radio have?
João
i attached a picture with the settings of my companion.
The Flashed Filename is:
Code: Select all
opentx-9x-heli-templates-ppmca-gvars-symlimits-autosource-autoswitch-dblkeys-battgraph-nogps-de.hex
i think i have a m128 chip on the board of the 9x is writen: FlySky V15
s_mack wrote: ↑Thu Dec 07, 2017 5:13 pm
Matzeeg3, did you go through the troubleshooting items I posted?
My guess is you didn't have the radio on. Flashing an unpowered target can erase it, but not program it.
Yes i did the troubleshooting but nothing change. I have the transmiter powered on as you can see on my picture bevor.
do i have to by a new mainboard?
Matze
Re: Blank screen after flashing opentx
Posted: Fri Dec 08, 2017 10:23 am
by matzeeg3
i just check the vcc power if i power on the transmiter i get +5v on the vcc.
Re: Blank screen after flashing opentx
Posted: Fri Dec 08, 2017 10:37 am
by jhsa
matzeeg3 wrote: ↑Fri Dec 08, 2017 8:39 am
i attached a picture with the settings of my companion.
Well, I only see a picture of Avrdude's output,not one of the configuration settings..
Please try adding -B 100 to the extra arguments field. Try doing a reading of the eeprom or firmware instead of trying to flash the radio..
João
Re: Blank screen after flashing opentx
Posted: Fri Dec 08, 2017 10:57 am
by matzeeg3
jhsa wrote: ↑Fri Dec 08, 2017 10:37 am
matzeeg3 wrote: ↑Fri Dec 08, 2017 8:39 am
i attached a picture with the settings of my companion.
Well, I only see a picture of Avrdude's output,not one of the configuration settings..
Please try adding -B 100 to the extra arguments field. Try doing a reading of the eeprom or firmware instead of trying to flash the radio..
João
Hi Joâo,
i did what you told see attached images.
Thanks for your help.
Re: Blank screen after flashing opentx
Posted: Fri Dec 08, 2017 11:17 am
by jhsa
It looks like you might have some connection problem. Could you please post a picture of your 9x mother board.
Also check that no pogo pins are bent on the smartieparts board, or that their springs are locked and not making contact.
You could also try eepe instead of companion.. Please download it at
www.er9x.com
João
Re: Blank screen after flashing opentx
Posted: Fri Dec 08, 2017 12:02 pm
by matzeeg3
jhsa wrote: ↑Fri Dec 08, 2017 11:17 am
It looks like you might have some connection problem. Could you please post a picture of your 9x mother board.
Also check that no pogo pins are bent on the smartieparts board, or that their springs are locked and not making contact.
You could also try eepe instead of companion.. Please download it at
www.er9x.com
João
i did it but it´s the same error
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 8:56 am
by matzeeg3
so am i right that i destroy my mainboard? is there a way to buy only a new processor or do i have to buy a new mainboard?
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 12:33 pm
by bob195558
Some info here about new processor if needed: (
viewtopic.php?f=95&t=3819&p=74105#p74046).
Do you know that your processor is bad ?
Bob B.
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 1:18 pm
by matzeeg3
no i don´t know if my processor is bad. but i don´t get any connection.
is this a good new prozessor:
https://www.ebay.de/itm/Atmel-ATMEGA128 ... SwuTxV~WWa
?
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 1:42 pm
by bob195558
Would be better to upgrade to the Atmel - ATMEGA2561-16AU chip: (
viewtopic.php?f=95&t=3819&p=71554#p71554).
The problem may be somewhere different, we are not sure you have a bad chip.
Bob B.
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 2:25 pm
by jhsa
please post a good picture of your 9x mainboard..
João
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 2:45 pm
by matzeeg3
is the atmega2561-16u compatible to OpenTX? (not eepx or er9x)
Pictures attached
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 4:06 pm
by jhsa
I have no idea if openTX supports the m2561. This chip does allow for more features. But I believe openTX is not being developed or maintained for the 9x stock board anymore. Er9x is.
It doesn't even support some features like the multi protocol module.. I personally think that you would be better off with er9x..
Can't see anything wrong with your board
João
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 4:30 pm
by matzeeg3
if we are on this step can you tell me in a short the diference between opentx and er9x?
if i decide to stay on opentx will the atmega a post will be the right or do i need the 16a Version? i don´t find informations for that
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 5:13 pm
by jhsa
matzeeg3 wrote: ↑Mon Dec 11, 2017 4:30 pm
if we are on this step can you tell me in a short the diference between opentx and er9x?
The major differences I already told you. Er9x is still maintained, so you have more chances of having new features, or support for more hardware implemented.
Er9x supports the 4 in 1 Multiprotocol module.
Er9x supports the addition of extra hardware like extra switches.
In my opinion er9x has a much better user interface and it is much easier to navigate the menus and find the options we need without having to scroll through many menus before you find the one you want. But this one is my opinion of course.
if i decide to stay on opentx will the atmega a post will be the right or do i need the 16a Version? i don´t find informations for that
Atmega128-16AU
João
Re: Blank screen after flashing opentx
Posted: Mon Dec 11, 2017 5:17 pm
by matzeeg3
Thanks a lot João
Re: Blank screen after flashing opentx
Posted: Thu Dec 14, 2017 5:05 pm
by matzeeg3
so i decided to the 128-16AU because i can use it with the er9x and opentx. now the complicated part the soldering.
have to finde time for it.
Re: Blank screen after flashing opentx
Posted: Thu Dec 14, 2017 5:32 pm
by jhsa
A good pair of eyes, a good magnifier, good soldering iron with a fine tip, good solder, lots of flux and lots of patience..
João
Re: RE: Re: Blank screen after flashing opentx
Posted: Thu Dec 14, 2017 5:39 pm
by matzeeg3
jhsa wrote:A good pair of eyes, a good magnifier, good soldering iron with a fine tip, good solder, lots of flux and lots of patience..
João
Let's see witch parts I have
Re: Blank screen after flashing opentx
Posted: Fri Dec 15, 2017 1:13 pm
by bob195558
Getting some "CHIP QUIK" will help a lot too.