openrcforums

Check that GPS module with U-center ....

br

Hugo, sorry.

My mistake, was thinking of

https://www.frsky-rc.com/product/v8r7-ii-2/

br KH

https://www.rc-network.de/threads/jeti- ... ul.589334/

br KH

Hugo123 wrote: ↑Sun Dec 06, 2020 9:00 pm ... and found out my FrSky receiver I bought together with the transmitter (V8R4-II, never used either ), probably needs to be replaced for a new one.

Why Hugo?

8 channel RX. For a start, it should do.

br KH

Sorry for the post. Think, I got it now (was late yesterday) :mrgreen: https://imgur.com/0JNtSjpl.png SEQUENCE_UNIT 2 --- the PPM-in pin SEQUENCE_0 --- PPM value 0% SEQUENCE_100 --- PPM value +100% But let me make a remark on 'SEQUENCE_UNIT' Documentation says: * oXs determines normally the sequence...

Just trying to put my hands on the sequencer. Just a bench test to understand .... (1W power LED, 2N2222 and 1K resistor) Works! But I do not understand the meaning of those 3 marked lines. Maybe I overlooked it in the documentation :? define SEQUENCE_UNIT 2 #define SEQUENCE_0 #define SEQUENCE_100 b...

what you thing about "in case Arduino can not handle"; using other controllers like teensy or stm32 based bords?. This question has been put forward a long time ago and several times. But you have to remember, mstrens is, more or less. the only one, who is putting his work into the oXs pr...

Get used to work with u-center before fussing around with oXs and GPS.

And when no USB UART is around, just use your Arduino to connect your GPS to u-center.

https://create.arduino.cc/projecthub/Pa ... ter-475533

br KH

I think, it would be easier, if you attach the complete oXs_config_basic.h and oXs_config_advanced.h file here as attachments

br KH

A short search in the internet --> XC6201P302PR

br KH

You have been through this here?

oXs_config_description.h

A very comprehensive description about oXs.

For your task, chapter 6

**** 6 - Voltage measurements and current sensor settings (optional) ***************************************************

br - KH

When I run the engine on the ground I get perfect, sensible read outs on my Horus all the way through the rpm range but the moment she is airborne the readings are all over the place That sounds strange. And when the plane is back on the ground, everything is fine again? On the ground, did you move...

So If I understand it wright I don't need the own Taranis firmware on the Taranis website because OpenTX is replacing the Taranis firmware ? You are still mixing things. https://imgur.com/LaQKhq3l.png There is only openTX on the webside. (And the HF module firmware) - There is the transmitter opera...

Was playing a bit with the SxR and thinking of putting it into one of my flying wings (replacing the standard rx), where the designer requests some differential. No idea .... Then I found Mikes posting. :D https://www.rcgroups.com/forums/showpost.php?p=40373724&postcount=7509 This posting pointe...

Thomas66 wrote: ↑Tue Sep 15, 2020 6:00 pm On the other hand I am not sure if it would be critical or not to use the 5V data / signal line (from a nano) to the 3.3 V data / signal line of the receiver.

Which RX please?

br KH

Yes, but the Nano is bigger, just like the blue pill ...

AND I DON'T HAVE THAT MUCH SPACE

br KH

The main reason I am not that happy with the Pro Mini board is, that the upload over a USB-TTL converter may or may not work. One shouldn't expect all are electronic experts, also some Pro Mini boards on the market have wrong/ reversed pins, some USB-TTL converters causing problems uploading while ...

Updating OpenTx without using Companion?

So the simple answer is NO!

cu KH

Hi João. Would prefer the Maple Mini (left one). But the size compared to the Pro mini! https://imgur.com/7UUVDLtl.png The one on the right, that is NOT a genuine Pro mini, but has a LGT8F328P. A bit faster than the original 328, End of the year I am going to do some tests with oXs on those. br KH

Hi Thomas. Did you see this post here? https://openrcforums.com/forum/viewtopic.php?f=86&t=12903&p=151388#p151388 Cappy used a 32U4 and mstrens (the oXs developer) answered that. Mstrens is not answering in this forum at the moment, maybe he is on holiday. Hopefully he does not have to fight...

Better make a fresh installation with LM 20 on your computer.

br KH

Hi, would like to ask a question about the Configurator. After years doing the oXs configuration with an editor, had a little deeper look at the Configurator. MPX + GPS. With oXs ver. 8.0.6 those were the MPX outputs 10 , GPS_COURSE , 1 , 1 , 0 , -16384 , 16383 , \ 11 , GPS_SPEED , 1 , 1 , 0 , -1638...

'Never change a running system' - old engineer dictum.

br KH

That warning is outdated, it was that way in 2.0.1 but they fixed it in 2.1.0. Of course they didn't update the info since the first time it was posted back in January. It is August now ;) With that kind of information policy from FrSky I don't have the slightest desire to update my working rc equi...

Hi. On FrSky News https://www.frsky-rc.com/news/ https://www.frsky-rc.com/important-firmware-update-accst-d16/ reads RF MODULE – iXJT & XJT X7 / X7S / X9DP (NON-2019) / X9DP SE (NON-2019) / X9E / X-Lite / X10 (NON-EXPRESS) / X10S (NON-EXPRESS) / X12S / XJT * Some Taranis X9D may have the compati...

Erkar29 wrote: ↑Mon Aug 03, 2020 5:53 am Thanks! Is there any radios that uses 5v on the pot? Maybe I need to buy another radio anyway for this special project.

Might have a look here

https://www.rcgroups.com/forums/showthr ... and-OpenTx

br KH

I am not twiddling with the TX, I do all my settings on the computer. Far more easy, at least for me.

And openTX 2.3.9 supports your TX. Get used to companion.



br KH

OpenTX!?

You do that in the mixer.

Here the flaps on my Milan. CH 3 and CH 4. Switch SB



br KH

Hi. Just put the flaps on a 3 position switch

cu KH

Hi Andrew. You are posting in the oXs section! That is another business ... ;) Frsky telemetry on the Evo screen I doubt that, but there are add. displays around https://www.mhm-modellbau.de/part-FrSky-FSD.php or https://www.rcmodelreviews.com/frsky_telemetry_project.shtml I personally prefer it the...