openrcforums

Hey experts, I've looked around this forum and can't find instructions on how to receive GPS on the radio. I have an Omnibus F4, Frsky X4R-SB with smart port connected to soft serial. Running betaflight 3.2.5. I have GPS connected to UART 1, I can see GPS coordinates on the OSD through my goggles. I...

Hi Mike, UPDATED: F8 appears to work correctly with items I was initially concerned about FASV (voltage), RSSI and TSSI. I see Amps working also (great). Is it possible to add LQ also? I see people using this now as a means of needing to return. I was also wondering if we could get mah used after L...

MikeB wrote: ↑Sun Jan 28, 2018 3:32 pm r221g5 is posted, but you need to go down a few posts in the test versions thread to find it.

Mike

Thank you

MikeB wrote: ↑Sat Jan 27, 2018 2:58 pm The nex test version (r221g5) will have support for the R9M included.

Mike

That is awesome, i was just going to ask if there were plans to support. Not a programmer so I'm useless in this matter.

Nope OpenTX supports them fully since 2.2.1. It was jsut a bit of a nightmare since FrSky's doc was pretty bad, AND what we had done initially changed later with a module firmware update. There are EU and US versions, which both have different power setting availability and telemetry availability t...

Has anybody tried to use the new FrSky R9M with the 9xr Pro and ErSky9x firmware? My brother just purchased the module and receiver so hoping it works out of the box with the firmware.

So i just updated my blog about this mod to the 9xr pro, hopefully this helps some one out. http://thehabitualcrasher.blogspot.com/ ... t.html?m=1

Good you now have it all working. Mike. Just flew 4 packs, the gimbals feel great though I'm not used to the way they feel so it's like learning all over again. Great radio, awesome firmware..... Also blew the R9 resistor somehow when I had the radio open so had to bridge that before I went out to ...

Ok got everything to work. Mike you were correct it was wire ordering so I took some time to swap wires around. So for anybody who purchase the PR10 Taranis Gimbals this was my wiring order. With the radio open and looking at the back of the gimbals and working left to right. Pitch and Roll (Right s...

Now when I lower the stick it reads: RV 00AD -71.9, at center RV 00FB 0.0, at the top RV 02E 93.5

After doing this it now rests at center RV 00ED -13.9

I've switched some wires around, everything is going in the correct direction but still don't get full throw after doing calibration. I'm going to trim some of the face plate and re-calibrate to see if that does the trick.

Don't go by the colours of the wires in the radio, they don't use standard colours, and sometimes they are different on different radios! The gimbal colours are red, brown and yellow. Red should be 3.3V, brown 0V and yellow is the signal. Use the measured voltages on the JST, 0V, and 3.29V are the ...

I don't like those (hex) values for RV. I'd expect around 0400 for the centre position. Please check you have 0V on the brown wire and 3.0V on the red wire goint to the gimbal. Mike. Ok now that I am on the correct side of the radio (Left side looking at the back, the left most JST reads 0, .3v, 3....

I don't like those (hex) values for RV. I'd expect around 0400 for the centre position. Please check you have 0V on the brown wire and 3.0V on the red wire goint to the gimbal. Mike. UPDATE: Silly me that was the throttle stick. I'll post the correct one in a few minutes Mike If I'm looking at the ...

In th DIAGANA screen, there is a 4-digit (hex) number beside RV. What values do you have there (and are they steady) when the stick is centered, and when the stick is at full deflection each way? Mike. At center screen shows: RV 06E9 1.9 A9 all the way down: RV 04AA (keeps changing, doesn't settle)...

Do you mean throttle stick when you say pitch? Make sure that when calibrate the sticks, all of them including the throttle stick are at center.. João Sent from my BLN-L21 using Tapatalk No, mode 2 right stick up and down is pitch, I fly miniquads I guess it's also called elevator. Yes all sticks a...

High guys, looks like it's been a bit since someone has posted in this thread. This thread is the closest thing I've found to my problem. I dropped my radio and broke a gimbal so I just installed two new taranis gimbals, the PR10. After I put everything back together I calibrated the sticks. Oh I gu...