Search found 1584 matches
- Wed Dec 02, 2020 6:25 pm
- Forum: General help (FrSky Taranis radio)
- Topic: disabling a switch by a logical switch
- Replies: 4
- Views: 5150
Re: disabling a switch by a logical switch
I just stumbled over your problem and had an idea that I realized in ER9x, but I assume it should be possible in OpenTx also For the throttle channel you use two mixer lines, one using curve1, the other using curve2. These lines are activated alternating by means of the status of the logic switch L1...
- Sun Nov 29, 2020 3:02 pm
- Forum: er9x
- Topic: [SOLVED] Yet another help request: Trainer/trainee, two 9X's ...
- Replies: 5
- Views: 3701
Re: Yet another help request: Trainer/trainee, two 9X's ...
Last thing during normal operation where Trainee is in control, I tested disconnecting the cable: the Trainer's software detects that it is an abnormal condition; even if I keep the TRN switch pushed, the software no longer takes into account the trainer port; it shortly hands the controls back to ...
- Sun Nov 29, 2020 12:05 am
- Forum: er9x
- Topic: [SOLVED] Yet another help request: Trainer/trainee, two 9X's ...
- Replies: 5
- Views: 3701
Re: Yet another help request: Trainer/trainee, two 9X's ...
As João said, the teachers radio must have the fully programmed model while the student radio has a simple 4 channel model without any further mixes. The stick values of the student radio will replace the stick values of the teachers radio and all mixes of the teachers radio will be supplied. So in ...
- Sun Oct 18, 2020 8:34 am
- Forum: Turnigy 9XR PRO radio
- Topic: HELP PLEASE! Possible encoder issue, don't want to fry the new board...
- Replies: 42
- Views: 25084
Re: HELP PLEASE! Possible encoder issue, don't want to fry the new board...
I will be doing so WITHOUT all the switches in place, and probably without the gimbals hooked up. I will get a switch error warning. No big deal, flip switches into correct... oh yeah there aren't any switches! :P "Or push any button" but that doesn't work with the encoder button. That's ...
- Fri Oct 16, 2020 5:49 pm
- Forum: Turnigy 9XR PRO radio
- Topic: HELP PLEASE! Possible encoder issue, don't want to fry the new board...
- Replies: 42
- Views: 25084
Re: HELP PLEASE! Possible encoder issue, don't want to fry the new board...
When I modded one of my old radios, (https://www.openrcforums.com/forum/viewtopic.php?f=61&t=7180) that also had independent trim pots, I finally decided to add digital trim switches at the left and right side of the housing and with help of Mike, modified the code to use the analog trim pots as...
- Thu Sep 24, 2020 3:58 pm
- Forum: ersky9xr
- Topic: twin turbine RPM
- Replies: 15
- Views: 9395
Re: twin turbine RPM
Thanks Mike
Reinhard
Reinhard
- Wed Sep 23, 2020 5:25 pm
- Forum: ersky9xr
- Topic: twin turbine RPM
- Replies: 15
- Views: 9395
Re: twin turbine RPM
Mike, could you, occasionally, push the latest modifications onto github ?
Reinhard
Reinhard
- Tue Sep 22, 2020 5:41 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
I downloaded the A3r223 fw version once more, compiled the mpm code 1.3.1.65 with multy_telemetry (outcommented some protocols) and now, the scanner is working !!!
And the mpm version is displayed with any protocol selection, not only wit AFHDS2A.
Thanks, Mike.
It's now working.
Reinhard
And the mpm version is displayed with any protocol selection, not only wit AFHDS2A.
Thanks, Mike.
It's now working.
Reinhard
- Tue Sep 22, 2020 8:39 am
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
I can't answer this in the moment as I used the precompiled version. And compiling it myself does not work with the plain code because it's size is to big for the module. I have not yet found out how to disable the USB support that is expected now for the code to fit the module. I outcommented a bun...
- Mon Sep 21, 2020 6:01 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
I have a 9XR Pro (FW Vers.: ersky9x-A3r223 from 17.07.2020) with external multi protocol module, running in serial mode. The fw version (1.3.1.65) of the MPM is only read out, when I select the AFHDS2A protocol. Once displayed, it is shown with any selected protocol. Is this normal ? When I select t...
- Sat Aug 15, 2020 8:17 am
- Forum: Hardware
- Topic: 9x Exit button size.
- Replies: 7
- Views: 4950
Re: 9x Exit button size.
9x radio normally uses 6x6x9.5 mm tactile switches
e.g.
https://www.ebay.de/itm/6x6mm-Momentary ... Swq2pbO1Wm
Reinhard
e.g.
https://www.ebay.de/itm/6x6mm-Momentary ... Swq2pbO1Wm
Reinhard
- Sun Apr 12, 2020 3:25 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
Thanks, Mike
this fix did the job.
No more 'No Telemetry' calls with the fully telemetry enabled module.
Reinhard
this fix did the job.
No more 'No Telemetry' calls with the fully telemetry enabled module.
Reinhard
- Sat Apr 11, 2020 9:12 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
That's correct, but that's not a problem as I only use flysky AFHDS receivers that don't have telemetry.
Reinhard
Reinhard
- Fri Apr 10, 2020 12:26 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
No Telemetry is also permanently called with the open TX version.
But when I compile the mpm code with "//define TELEMETRY" then there are nomore calls of 'No Telemetry'
Reinhard
But when I compile the mpm code with "//define TELEMETRY" then there are nomore calls of 'No Telemetry'
Reinhard
- Thu Apr 09, 2020 11:03 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
I had the mpm already updated with the recent precompiled version "multi-stm-ersky-reta-inv-v1.3.0.76" (but redid it, to be sure) No idea how that fw is compiled regarding MULTI_TELEMETRY or MULTI_STATUS. Nevertheless, without a telemetry signal available, shouldn't it tell me the missing ...
- Thu Apr 09, 2020 11:04 am
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
Mike, thanks for looking into that problem. You made me uncertain about my problem, so I wanted to verify it again.... and got ... no problem ?????? even with fw versions that I knew they had shown the same symptom. My 'dirty' temporary circumvention (as I do not use any telemetry) of that permanent...
- Wed Apr 08, 2020 4:50 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: RPM resolution?
- Replies: 232
- Views: 145642
Re: RPM resolution?
I also use the "Save as" method to save the complete set of files that belong to a project. BUT there is sometimes a little problem (at least with my version 1.8.0). You can start the arduino ide either by clicking the arduiono.exe and it will open your last project. That's ok. You can als...
- Mon Apr 06, 2020 12:33 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Continously "No Telemetry"
Ersky9x without telemetry using Flysky protocol By Chance I found the reason why one of my models was permanently telling me "No Telemetry" When the Telemetry Usr Protocol is set to HUBRAW the radio permanently, with maximum repetitionrate, tells you that there is no telemetry This Bug is ...
- Mon Feb 17, 2020 6:16 pm
- Forum: Retro Radios
- Topic: Reviving a Multiplex Cockpit SX transmitter
- Replies: 2
- Views: 19438
Reviving a Multiplex Cockpit SX transmitter
Some time ago I got a Multiplex Cockpit SX transmitter with defective electronics. As the mechanics of that transmitter are really good, I was hoping to rebuild the required electronics in the way of the ER9x. I didn't want to have the voice module or a trainer connector as the original radio had it...
- Tue Jan 21, 2020 11:33 pm
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: RPM resolution?
- Replies: 232
- Views: 145642
Re: RPM resolution?
regarding to intermittend compile errors with the Arduino IDE There is/ or was? a problem with the linker (at least until the version 1.8.0 that I still use). I had the problem that least modifications of a file, e.g. adding a line of code or even deleting a commentline could lead to a "load er...
- Tue Jan 07, 2020 8:40 am
- Forum: er9x
- Topic: er9x development
- Replies: 3179
- Views: 1459884
Re: er9x development
Thanks Mike
Reinhard
Reinhard
- Mon Jan 06, 2020 10:53 pm
- Forum: er9x
- Topic: er9x development
- Replies: 3179
- Views: 1459884
Status of Logic switch LI no longer displayed
SInce the Git updates of 2019-07-30 the status of the IDx switch is shown on the system page that shows the status of hardware and logic switches. That shifted all the following LSx switches one position to the end, thereby loosing the last logic switch LI from the last subview. The TRN switch displ...
- Tue Dec 17, 2019 10:30 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
Thank you, Mike
Reinhard
Reinhard
- Tue Dec 17, 2019 10:29 pm
- Forum: Software
- Topic: 9XR Pro connection issues
- Replies: 46
- Views: 27721
Re: 9XR Pro connection issues
That delay is still there, exactly as with your original programming.
In your programming, you use three logic switches (L6, L7 and LA) that can be replaced with a single one (LB in my example) that has the same functionality. Just another way of programming for the same thing.
Reinhard
In your programming, you use three logic switches (L6, L7 and LA) that can be replaced with a single one (LB in my example) that has the same functionality. Just another way of programming for the same thing.
Reinhard
- Tue Dec 17, 2019 7:02 pm
- Forum: erskyTx (was ersky9x)
- Topic: Ersky9x Bug Reporting
- Replies: 416
- Views: 342981
Re: Ersky9x Bug Reporting
I downloaded the github code from 2019-11-27 and there are some problems. ErskyTx: Compile error with AR9x/9XRpro ==================== Compile parameters: make REVB=1 STAMP=1 DEBUG=1 REV=222 USER=ReSt menus.cpp: In function 'void menuProcIndex(uint8_t)': menus.cpp:24513:28: error: 'BtStatus' was not...
- Tue Dec 17, 2019 6:39 pm
- Forum: Software
- Topic: 9XR Pro connection issues
- Replies: 46
- Views: 27721
Re: 9XR Pro connection issues
I had a look into your file and here are some comments You can get the function of the three switches L8,L9,LA with a single switch of |v| > val Rud 96 ( |v| means absolut value of v, gives always a positiv value for v from -100 to +100) You probably connect Switches to Ch7 and Ch8 to power on/off t...
- Sat Dec 07, 2019 9:47 pm
- Forum: Turnigy 9XR PRO radio
- Topic: Voice files for 9XR-PRO with ersky9x
- Replies: 84
- Views: 131375
Re: Voice files for 9XR-PRO with ersky9x
If I remember correctly, it was said, the files are displayed in the sequence, they have been written onto the card.
Reinhard
Reinhard
- Tue Dec 03, 2019 2:10 pm
- Forum: General help (FrSky Taranis radio)
- Topic: module for a rover in TARANIS
- Replies: 4
- Views: 4469
Re: module for a rover in TARANIS
Have a look at this thread
viewtopic.php?f=5&t=12296#p146899
(I don't know the sense of the flight controller in your configuration)
Maybe it gives you an idea of how to do what you want.
Reinhard
viewtopic.php?f=5&t=12296#p146899
(I don't know the sense of the flight controller in your configuration)
Maybe it gives you an idea of how to do what you want.
Reinhard
- Sun Oct 27, 2019 1:41 pm
- Forum: er9x
- Topic: How to mix the input from two sticks to control 2 motors
- Replies: 23
- Views: 15186
Re: How to mix the input from two sticks to control 2 motors
@pstimpel: The solution given above can slow the inner motor down to 0. Here comes a more advanced setup that can drive the inner motor to full reverse speed. This is what I have for a 2 motor ship, but in the endeffect does the same for a bagger or a tank. But in the moment this setup is for a mode...
- Sat Oct 26, 2019 10:29 pm
- Forum: er9x
- Topic: How to mix the input from two sticks to control 2 motors
- Replies: 23
- Views: 15186
Re: How to mix the input from two sticks to control 2 motors
Try the following: CH01 -100% RUD * +100% THR (This is a multiply mix!!) +100% THR Curve(c9) CH02 +100% RUD * +100% THR (This is a multiply mix!!) +100% THR Curve(c9) Curve C9 100, 67, 33, 0,0,0,-33, -67, -100 The curve is not required, but gives you a wide dead zone around neutral, so that both mot...