openrcforums

Hy, Open9x, r1361, normal Flysky-Modul, 1K mod, I have tested at DSC Jacket, Oszi at 3,5mm Jacket, and 6 channel Receiver with 4Servos to see HF working Power Switch off Put Jacket in, TH9x starts, get on, Setup screen 2/6 "Trainer", its ok! that is studentmode for output PPM-signals Power...

Hy,
In Companion9x the download filename should added with the release-Nr.
not only with the options
Sometimes I went back to an old version, but its overwritten
(open9x with standard board)

Helle

how can I test it, because I have only the possibility to use Companion9x for option, download and flash

In Companion9x the download filename should added with the release-Nr.
not only with the options

Helle

only debug 4/6 Trimm displaying on the screeen is allways 0
Trimmswitsch itself works
open9x standard board

the other 7 switsches works and display correkt
older release 1195 it worked correkt 1/0

helle

Error in open9x r1336, last release load from companion9x

Debug Screeen 4/6 Trimswitches don´t work on LCDscreen, allways 0

Helle

Which is your PPM2USB Interface ?
Take a picture

use the Atmega8 and it will run!!

Hell

Hy,

or this one.

Helle

Hy, here is a schematic that will allways work with TH9x and many others TX with 4,6,8,10 channels from 1,7V to 5V from 22,5ms to 10ms framerate with positiv or negativ PPM signal cost 3€ ppm2usb_adapter_schematics..jpg Atmega8 with 12Mhz Quarz, USB is software, softwarefile is main.hex main.hex so ...

Hy, I had same Porblems! The effect, that Channel 1 in the PPM-format does not work or no channel does work is normaly a Problem of the PPM2USB Stick, most of them dont work korrekt. Most of them are from ebay for 4-10 € with lots of kabels In r1195 there is a problem with the positiv an negativ PPM...

Hy, I had same Porblems! The effect, that Channel 1 in the PPM-format does not work is normaly a Problem of the PPM2USB Stick, most of them dont work korrekt. Most of them are from ebay for 4-10 € with lots of kabels In r1195 there is a problem with the positiv an negativ PPM-Pulses, they are change...

Hy,

thanks!

Helle

Hy, This is at the DSC 3,5mm Jacket output für FlightSim with PPMsim and for student output PPM and PPM16, all the same. I checked it because I got problems with a USB-Simulator Cable, doesn´t work. Now, please could onyone test it again and how can we change it in the next release of Open9x helle

hy, yes, the Signals are ok, but the setup at the open9x softwere is wrong! see Modell setup Page Setup 01 2/11 ... ..... 22,5ms 300u + for Positiv , but negativ Signal comes out, idle high level, pules low 22,5ms 300u - for Negativ, but positiv Signal comes out, idle low level, pulses high Thats wh...

Hy, I have flashed the latest open9x, relesase r1195, and cheked the output signal at the 3,5mm DSC-Jacket with an Oszi When I set PPM to Positv (+) a negativ PPM-Signal comes out When I set PPM to Negativ( -) a positiv PPM-Signal comes out I think this is not korrekt, could anyone test it again. I ...

Hy,

schau mal da rein da ist alles in Deutsch erklärt
th9x, sender, umbauen, flashen, software, companion, usw.

http://fpv-community.de/showthread.php? ... 9x-Flashen

Helle